T-SB-0090-13

VENZA
01 Install antenna .................................................................
FUNCTIONAL OPERATION
Apply parking brake and cycle ignition “IG-ON”; place gear selector in reverse;
turn on lights and rear defogger. Unlock doors; release fuel door.
01
02
03
04
05
06
07
08
09
10
11
Check dome, courtesy, map, and sun visor lights* ..........
Check warning/indicator lights, gauges, and horn ...........
Check windshield wipers and washers ............................
Check headlights, instrument lights, turn signals,
emergency flashers, and brake lights ..............................
Check inside/outside rear view mirror operation/
adjustment .......................................................................
Check cigarette lighter* and power outlets ......................
Check audio/navigation*/backup camera* systems and
set clock ..........................................................................
Verify Entune/Navigation software version (Display
Audio, Non-HDD Type only)* ........................................
Check sliding roof* .........................................................
Install shift-lock override button cover ............................
Check Rear Seat Entertainment System operation* ........
WALKAROUND INSPECTION
Start at left front door. Check window and door lock operation (from master power
switch, if equipped). Continue around vehicle in a counterclockwise direction
checking each door and window operation, child door locks, seat belts, interior
condition, all lights, luggage compartment contents. Finish by checking headlight
aim and continue into UNDER HOOD checks.
01 Check Smart Key System*............................................
02 Check door and door lock operation, including each
wireless remote control/theft deterrent system* ..............
03 Check window operation .................................................
04 Check that engine starts with all keys ............................
05 Check that child safety door locks are in normal
(unlocked) position ..........................................................
06 Check seats and seat belt operation ...............................
07 Check rear defogger/rear view mirror defogger* .............
08 Check side marker, tail, backup, and license plate lights
09 Check luggage compartment light* and trim appearance
10 Adjust spare tire pressure, inspect for damage, and
check jack and tool installation ........................................
11 Check headlight aim ........................................................
UNDER HOOD
01
02
03
04
05
Check engine oil level .....................................................
Check brake fluid level.....................................................
Check engine coolant level ..............................................
Check windshield washer fluid level ................................
Check battery state-of-charge using Digital Battery
System Analyzer (SOC Reading: ___________%) .....
06 Inspect for fuel, oil, coolant, and other fluid leaks ............
OK
UNDER VEHICLE (ON HOIST)
July 2013
Adjust/
Adjust/
Repair
Repair
OK
BEFORE INSPECTION
Adjust/
Repair
2014 PRE-DELIVERY SERVICE CHECK SHEET
01 Remove disc brake anti-rust covers/anti-corrosion
wheel film* .....................................................................
02 Inspect tires for defects/damage .....................................
03 Verify Tire Pressure Warning System (TPWS) (see
page 2) ...........................................................................
04 Install wheel covers/caps/spare tire wheel covers* ........
05 Inspect for fuel, oil, coolant, and other fluid leaks ...........
06 Inspect under the vehicle for damage, rust, etc. ..............
07 Visually check bolts and nuts on chassis and powertrain
for looseness ...................................................................
08 Install rubber body plugs* (stored in glove box or center
console)...........................................................................
ROAD TEST
A complete road test helps assure customer satisfaction. Drive vehicle over a
variety of road surfaces and driving conditions. Check for unusual noise and
driving performance.
Enter Odometer Readings
Reading Before Test: _______________ Reading After Test: ________________
01
02
03
04
05
06
07
08
09
10
11
12
Check cold engine operation ...........................................
Check engine operation during warm-up .........................
Check engine at normal operating temperature ..............
Check automatic transmission operation .........................
Check brake and parking brake operation .......................
Check steering operation & off-center/vehicle pull/flutter
Inspect for abnormal noise and vibration .........................
Inspect for squeaks and rattles ........................................
Check front and rear* heater and A/C operation..............
Check cruise control operation* ......................................
Check front seat heater/ventilation operation* .................
Set/calibrate compass* (see page 2) ..............................
FINAL INSPECTION AND CLEANING
01 Remove interior protective covers, unnecessary labels,
tags, etc. (Remove just before delivery to customer).......
02 Visually inspect all interior parts for installation,
damage, fit, dirt, etc. ........................................................
03 Verify floor mat application and install using
retaining clips* ...............................................................
04 Remove Rapgard™ and clear protective bumper film*....
05 Wash and clean vehicle ...................................................
06 Inspect paint finish for scratches, chips, rust, dents,
damage, etc. ....................................................................
07 Inspect exterior body parts for proper installation,
damage, rust, etc. ............................................................
08 Place oil change sticker on inside of windshield, top
left corner ........................................................................
09 Place Owner’s Guide & first aid kit portfolio* in glove box
10 Perform Techstream Health Check ................................
11 Install front license plate and mounting bracket* (see
page 2) ............................................................................
* Inspect or install when equipped/required.
Completion and retention of this from is required to comply with Toyota’s Warranty Policy.
TECHNICIAN’S SIGNATURE
SERVICE MANAGER’S SIGNATURE
NAME (PLEASE PRINT)
NAME (PLEASE PRINT)
Date
Dealer Name
Dealer Code
We hereby certify that all items
on this form have been checked
and corrected for proper
operation as required.
Vehicle Identification Number (Sticker)
TPWS VERIFICATION
1. Connect Techstream to DLC3.
2. Adjust all tires (except the spare tire) to the standard tire inflation pressure, as indicated on the tire and loading
information label on the vehicle.
3. Cycle the ignition switch to the “IG-ON” mode.
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder than shop temperature,
perform a Health Check using Techstream and select the “Compensation Tire Pressure” checkbox. Compensation
pressures will be displayed on the Health Check results screen. Adjust the tire pressure when the tires are cold.
4. Check the tire pressure of all tires using Techstream. If the tire pressure values cannot be displayed, the system is not
operating properly. Refer to the Repair Manual.
5. Remove the ID number labels that are attached to each wheel and discard.
NOTE
If the tire pressure values are not properly displayed (example: showing –14 psi, –100 kPa, etc.) the data from the
transmitter has not been received.
COMPASS CALIBRATION
Refer to the Repair Manual for the Calibration procedure for vehicles equipped with a compass in the rear view mirror.
NOTE
• Do NOT perform calibration of the compass in a place where the Earth’s magnetic field is subject to interference
(underground parking, under a steel tower, between buildings, roof parking, near a railroad crossing, near a large
vehicle, etc.).
• During calibration, do NOT operate electric systems (moon roof, power windows, etc.) as they may interfere with the
calibration.
FRONT LICENSE PLATE AND MOUNTING BRACKET INSTALLATION*
Front License Plate Bracket: P/N 75101-0T010
1
1. Insert the front license plate into the mounting bracket.
2. Align the installation holes on the mounting bracket and front
license plate with the dimples on the front bumper.
3. Screw in the 2 self-tapping screws directly into the
dimples to install the front license plate and mounting bracket.
3
NOTICE
• Do NOT pre-drill holes into the bumper.
• Do NOT overtighten the self-tapping screws.
2
4
1
2
3
4
Dimples
Front License Plate Mounting Bracket
License Plate
Self-Tapping Screws