T-SB-0265-17

iA
UNDER VEHICLE (ON HOIST)
1 Install AUDIO1 and ROOM fuses (See page 2) ...................
1 Remove disc brake anti-rust covers/anti-corrosion
wheel film* (remove just prior to customer delivery) ......
2 Initialize Tire Pressure Warning System (TPWS)
(See page 2) ........................................................................
3 Inspect tires for defects/damage ...........................................
4 Install wheel caps (stored in glove box) ................................
5 Inspect for fuel, oil, coolant, and other fluid leaks .................
6 Visually check bolts and nuts on chassis and powertrain
for looseness ........................................................................
7 Inspect under the vehicle for damage, rust, etc. ..................
FUNCTIONAL OPERATION
Apply parking brake and cycle ignition “IG-ON;” place gear selector in reverse; turn
on lights and rear defogger. Unlock all doors, release fuel door, release trunk hatch.
1
2
3
4
5
6
7
8
OK
BEFORE INSPECTION
August 2017
Adjust\
Repair
OK
2018 PRE-DELIVERY SERVICE CHECK SHEET
Adjust\
Repair
Market: USA
Check dome, courtesy, map, and sun visor lights* ...............
Check warning/indicator lights, gauges, and horn ................
Check windshield wipers and washers .................................
Check headlights, instrument lights, turn signals,
emergency flashers, and brake lights ...................................
Check inside/outside rear view mirror
operation/adjustment ............................................................
Check power outlet ...............................................................
Check audio/navigation*/backup camera* systems, and
set clock................................................................................
Set Oil Change Maintenance Monitor to 7,500 miles .......
ROAD TEST
A complete road test helps assure customer satisfaction. Drive vehicle over a
variety of road surfaces and driving conditions. Check for unusual noise and
driving performance.
Enter Odometer Readings
WALKAROUND INSPECTION
Start at left front door. Check window and door lock operation (from master power
switch, if equipped). Continue around vehicle in a counterclockwise direction
checking each door and window operation, child door locks, seat belts, interior
condition, all lights, luggage compartment contents. Finish by checking
headlight aim.
Reading Before Test: _______________ Reading After Test: ________________
1
2
3
4
5
6
7
8
9
10
11
1 Check door and door lock operation, including each
wireless remote control/theft deterrent system* ....................
2 Check power window operation ............................................
3 Check that engine starts with all keys ...................................
4 Check seats and seat belt operation ....................................
5 Check rear defogger .............................................................
6 Check side marker, tail, backup, and license plate lights......
7 Check rear cargo area trim appearance ...............................
8 Adjust spare tire pressure, inspect for damage, and check
jack and tool installation........................................................
9 Check headlight aim .............................................................
Check cold engine operation ................................................
Check engine operation during warm-up ..............................
Check engine operation at normal operating temperature ....
Check clutch/automatic transmission operation....................
Check brake and parking brake operation ............................
Check steering operation and off-center/vehicle pull/flutter ..
Inspect for abnormal noise and vibration ..............................
Inspect for squeaks and rattles .............................................
Check heater and A/C operation ..........................................
Check speedometer operation..............................................
Check cruise control operation .............................................
FINAL INSPECTION AND CLEANING
UNDER HOOD
1 Remove interior protective covers, unnecessary labels,
tags, etc. (Remove just before delivery to customer) ............
2 Verify floor mat application and install using
retaining clips* ....................................................................
3 Visually inspect all interior parts for installation, damage,
fit, dirt, etc. ...........................................................................
4 Remove Rapgard™ & clear protective bumper film* ............
5 Wash and clean vehicle ........................................................
6 Inspect paint finish for scratches, chips, rust, dents,
damage, etc. ........................................................................
7 Inspect exterior body parts for proper installation,
damage, rust, etc. ................................................................
8 Place oil change sticker on inside of windshield, top
left corner..............................................................................
9 Perform Techstream Health Check ......................................
10 Place Owner’s Manual portfolio* in glove box.......................
11 Install front license plate* (See page 2) ................................
1
2
3
4
5
Check engine oil and ATM* fluid levels.................................
Check brake and clutch* fluid levels .....................................
Check engine coolant level ...................................................
Check windshield washer fluid level .....................................
Check battery State-Of-Charge using Digital Battery
System Analyzer (SOC Reading: ___________%) ...........
6 Inspect for fuel, oil, coolant, and other fluid leaks .................
Notes:
* Inspect or install when equipped/required.
Completion and retention of this form is required to comply with Toyota’s Warranty Policy.
TECHNICIAN’S SIGNATURE
NAME (PLEASE PRINT)
Date
SERVICE MANAGER’S SIGNATURE
We hereby certify that all items
on this form have been checked
and corrected for proper
operation as required.
NAME (PLEASE PRINT)
Dealer Name
Dealer Code
Vehicle Identification Number (Sticker)
AUDIO1 FUSE AND ROOM FUSE INSTALLATION
To minimize battery discharge, the AUDIO1 and ROOM fuses have been removed and are stored in the engine compartment Relay
Block. Install the AUDIO1 and ROOM fuses (both 25A) and confirm ALL related DTCs are cleared.
1. Remove AUDIO1 Fuse (25A) and ROOM Fuse (25A).
2. Install ROOM Fuse (25A) into original location.
3. Install AUDIO1 Fuse (25A) into original location.
2
1
4
3
1 Relay and Fuse Block
2 Relay and Fuse Block Cover
3 Remove AUDIO1 Fuse (25A) and
ROOM Fuse (25A)
4 Install ROOM Fuse (25A) Here
(Original Location)
5 Install AUDIO1 Fuse (25A) Here
(Original Location)
6 Relay and Fuse Block Location
5
6
TIRE PRESSURE WARNING SYSTEM (TPWS) INITIALIZATION
AFTER adjusting ALL tires to the standard air pressure, perform initialization of the TPWS during PDS according to the procedure
outlined below.
1. Park the vehicle on a safe level area.
2. Adjust ALL four tire pressures to the specification while the tires are cold.
NOTICE
In order for the tires to be considered “cold” leave the vehicle for 1 hour, or if the vehicle is driven, do so within 0.99
miles (1.6 km).
3. Switch the ignition switch ON (engine OFF or ON).
4. Press and hold the tire pressure warning reset switch until
the tire pressure monitoring system warning light flashes
one or two times and the indicator alarm sounds one time.
HINT
 When the TPWS initialization is performed, learning initiates.
 While the TPWS is undergoing learning, its primary functions do
NOT operate.
FRONT LICENSE PLATE INSTALLATION*
For states that require a front license plate, follow the front license plate installation procedure below.
1. Align the installation holes on the front license plate with the dimples
on the front bumper.
2. Directly screw two self-tapping screws into the dimples to install the
front license plate. Use self-tapping screws of a non-corroding type
with the following dimensions:
Nominal Length: 15.0 – 20.0 mm (0.60 – 0.79 in.)
Diameter: 6.0 mm (0.24 in.)
NOTICE
 Do NOT pre-drill holes into the bumper.
 Do NOT overtighten the self-tapping screws.