S-SB-0009-14 Rev
Service Bulletin Details
Public Details for: S-SB-0009-14 Rev
Tsb: some 2013 ? 2014 model year fr-s vehicles may exhibit multiple concerns from the outer weatherstrip (belt molding). The cross section of the weatherstrip has been revised to limit the amount of water passing into the door. If the felt
Models from 2014
2014 SCION FR-S |
Models from 2013
2013 SCION FR-S |
S-SB-0009-14 Rev2 April 23, 2014 Outside Door Weatherstrip - Multiple Concerns Service Category Vehicle Exterior Section Door/Hatch USA Market Applicability YEAR(S) MODEL(S) 2013 – 2014 FR-S ADDITIONAL INFORMATION REVISION NOTICE July 17, 2014 Rev2: • The Parts Information and Repair Procedure sections have been updated. June 16, 2014 Rev1: • The Parts Information section has been updated. Any previous printed versions of this bulletin should be discarded. Introduction Some 2013 – 2014 model year FR-S vehicles may exhibit multiple concerns from the Outer Weatherstrip (belt molding). The cross section of the weatherstrip has been revised to limit the amount of water passing into the door. If the felt attached to the window stabilizers/guides accumulate water, the vehicle may also make noise from the stabilizers/guides during window operation. In some cases, the felt on the stabilizers/guides may freeze to the window or detach from the plastic backing and damage the window. Symptoms may include: • Noise coming from the weatherstrip during window operation, especially when wet. • Loosening of the weatherstrip from the door. • Inversion of the weatherstrip during window operation. • Noise from the stabilizers/guides during window operation. • Scratches on the glass from worn stabilizers. If the vehicle displays these symptoms, follow the procedures described in this bulletin to address the condition(s). © 2014 Toyota Motor Sales, USA Page 1 of 6 Rev2 S-SB-0009-14 April 23, 2014 Page 2 of 6 Outside Door Weatherstrip - Multiple Concerns Production Change Information This bulletin applies to vehicles produced BEFORE the Production Change Effective VIN shown below. MODEL PRODUCTION CHANGE EFFECTIVE VIN FR-S JF1ZNAA1#E8705465 Parts Information PART NUMBER PART NAME QTY SU003-05207 Outer Weatherstrip, RH 1 SU003-05208 Outer Weatherstrip, LH 1 SU003-01616 Stabilizer, Front Door Glass, Outer (Per Door) 2 SU003-01617 Stabilizer, Front Door Glass, Inner (Per Door) 1 PREVIOUS NEW SU003-04334 SU003-04531 SU003-04771 SU003-04335 SU003-04532 SU003-04772 Warranty Information OP CODE DESCRIPTION TIME BD1408 Replace Front Door Panel Sub-assembly (One Side) 1.6 Combo A Replace Front Door Panel Sub-assembly (Other Side) 1.6 Combo B Replace Window Stabilizer (One Side) 0.1 Combo C Replace Window Stabilizer (Other Side) 0.1 OFP T1 T2 SU003-04334 SU003-04335 SU003-04531 SU003-04532 SU003-04771 SU003-04772 93 13 APPLICABLE WARRANTY • This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date. • Warranty application is limited to occurrence of the specified condition described in this bulletin. © 2014 Toyota Motor Sales, USA S-SB-0009-14 Rev2 April 23, 2014 Page 3 of 6 Outside Door Weatherstrip - Multiple Concerns Required Tools & Equipment SPECIAL SERVICE TOOLS (SST) PART NUMBER QTY Plastic Pry Tool Kit* 00002-06020-01 1 Tool, Front Door Glass Adj* 09812-18010-01 1 REQUIRED MATERIAL QUANTITY Toyota Genuine Adhesive 1344, Three Bond 1344, Loctite® 242, or Equivalent (for window nuts) As Needed * Essential SST. NOTE Additional SSTs may be ordered by calling 1-800-933-8335. Overview Procedure 1. Confirm the condition. 2. Disassemble door per the Repair Manual. 3. Reassemble door and adjust window glass. 4. Reinitialize window. Inspection Procedure NOTICE BEFORE performing the procedures in this bulletin, ensure there is NO body or door damage that may affect the alignment of the side window glass. Removal Procedure NOTE Use the same procedure for both the RH and LH sides. Refer to the Technical Information System (TIS), applicable model and model year Repair Manual: • 2013 / 2014 FR-S: Vehicle Exterior – Exterior Panels / Trim – “Front Door Belt Moulding: Removal” 1. Disconnect cable from the negative (–) battery terminal. 2. Remove front door armrest cover. 3. Remove front door trim board sub-assembly with power window switch assembly. © 2014 Toyota Motor Sales, USA S-SB-0009-14 Rev2 April 23, 2014 Page 4 of 6 Outside Door Weatherstrip - Multiple Concerns Removal Procedure (Continued) 4. Remove front door service hole cover. 5. Remove front door glass sub-assembly. Refer to TIS, applicable model and model year Repair Manual. • 2013 / 2014 FR-S: Vehicle Exterior – Front Door – “Door / Hatch: Front Door: Disassembly” HINT Note position of the inner stabilizer bolt as a reference for window alignment before removing the Front Door Glass sub-assembly. 6. Remove front door glass Outer Weatherstrip assembly. Figure 1.. A. Remove the screw. B. If necessary, use a screwdriver to disengage the claw and remove the front door glass Outer Weatherstrip assembly. NOTICE Tape the screwdriver tip before use. 7. Inspect Door Glass Inner and Outer Stabilizers for wear or damage. NOTE Replace stabilizers if felt guide surface is worn or damaged. © 2014 Toyota Motor Sales, USA S-SB-0009-14 Rev2 April 23, 2014 Outside Door Weatherstrip - Multiple Concerns Installation Procedure NOTE Use the same procedure for both the RH and LH sides. 1. Install Inner and Outer Window Stabilizers if necessary. HINT Leave Inner Window Stabilizer bolt loose until window is installed. 2. Install front door glass Outer Weatherstrip assembly. Figure 2.. Engage the claws to install the screw and a NEW front door glass Outer Weatherstrip assembly as shown. NOTE Ensure proper installation of Outer Weatherstrip by confirming that the claw attached to the weatherstrip is fully engaged. 3. Install front door glass sub-assembly. Refer to TIS, applicable model and model year Repair Manual: • 2013 / 2014 FR-S: Vehicle Exterior – Door/Hatch – “Front Door: Reassembly” NOTE Use Loctite™ 242 or equivalent on front door glass flange nuts. 4. Adjust front door glass sub-assembly. Refer to TIS, applicable model and model year Repair Manual: • 2013 / 2014 FR-S: Vehicle Exterior – Door/Hatch – “Front Door: Adjustment” HINT Align Inner Stabilizer bolt to original position as a reference for window alignment. © 2014 Toyota Motor Sales, USA Page 5 of 6 S-SB-0009-14 Rev2 April 23, 2014 Outside Door Weatherstrip - Multiple Concerns Installation Procedure (Continued) 5. Install front door service hole cover. 6. Install front door trim board sub-assembly with power window switch assembly. 7. Install front door armrest cover. 8. Connect cable to negative (–) battery terminal. Torque: 6.0 N*m (61 kgf*cm, 53 in*lbf) 9. Initialize power window control system. 10. Confirm the repair. © 2014 Toyota Motor Sales, USA Page 6 of 6