S-SB-0016-14

S-SB-0016-14
June 23, 2014
Outer Rear View Mirror Looseness
Service
Category
Vehicle Exterior
Section
Mirror (ext)
Market
USA
Applicability
YEAR(S)
MODEL(S)
2013
FR-S
ADDITIONAL INFORMATION
Introduction
Some 2013 model year FR-S vehicles may exhibit a condition where the outer rear view mirrors
vibrate while moving, most visibly at highway speeds. The retaining bolts and mirror housing base
have been revised to better ensure the stability of the mirror housing. Follow the procedure in
this bulletin to address this condition.
Production Change Information
This bulletin applies to vehicles produced BEFORE the Production Change Effective VIN
shown below.
MODEL
DRIVETRAIN
PRODUCTION CHANGE EFFECTIVE VIN
FR-S
2WD
JF1ZNAA1#D2718009
Warranty Information
OP CODE
BD1416
BD1417
DESCRIPTION
R & R Mirror Bolts (One Side)
R & R Mirror Bolts (Both Sides)
TIME
0.8
1.0
OFP
T1
T2
SU003-03048 (RH)
SU003-03054 (RH)
SU003-04699 (RH)
SU003-04705 (RH)
SU003-03049 (LH)
SU003-03055 (LH)
SU003-04700 (LH)
SU003-04706 (LH)
62
14
APPLICABLE WARRANTY
• This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months
or 36,000 miles, whichever occurs first, from the vehicle’s in-service date.
• Warranty application is limited to occurrence of the specified condition described in
this bulletin.
© 2014 Toyota Motor Sales, USA
Page 1 of 3
June 23, 2014
S-SB-0016-14
Page 2 of 3
Outer Rear View Mirror Looseness
Parts Information
PART NUMBER
PART NAME
QTY
SU003-04923
Mirror Bolt, FLG
3
Required Tools & Equipment
REQUIRED MATERIAL
QUANTITY
Loctite® 243™ Threadlocker, or Equivalent
As Needed
Repair Procedure
1. Confirm the condition described in the Introduction.
2. Verify torque on the outer rear view mirror housing mounting bolts. Tighten and retest to confirm
cause or looseness.
Does the mirror still vibrate after tightening the bolts?
• YES — This bulletin does NOT apply. Continue diagnosis using the applicable
Repair Manual.
• NO — Continue to step 3.
3. Remove the outer rear view mirror assembly.
Refer to the Technical Information System (TIS), applicable model and model year
Repair Manual:
• 2013 FR-S:
Vehicle Exterior – Mirror (ext) – “Mirror (Ext): Outer Rear View Mirror: Removal”
4. Remove the 3 Phillips screws, which hold the
mirror head to the base.
Figure 1.
.
1
NOTICE
Avoid damaging the Phillips drive portion of
the screws by using the appropriate Phillips
screwdriver. The screws are installed with
a threadlocking compound and may require
some extra torque to remove.
2
1
Remove These 3 Screws
2
Do NOT Remove This Screw
© 2014 Toyota Motor Sales, USA
June 23, 2014
S-SB-0016-14
Page 3 of 3
Outer Rear View Mirror Looseness
Repair Procedure (Continued)
5. Apply Loctite® 243™ Threadlocker or equivalent compound to threads of NEW bolts,
and install.
Torque: 4 N*m (40.8 kgf*cm, 35.4 in*lbf)
6. Install the outer rear view mirror assembly.
Refer to TIS, applicable model and model year Repair Manual:
• 2013 FR-S:
Vehicle Exterior – Mirror (ext) – “Mirror (Ext): Outer Rear View Mirror: Installation”
7. Confirm the repair.
© 2014 Toyota Motor Sales, USA