FSB284-065

Volvo Trucks North
America
Greensboro, NC USA
Field Service Bulletin
Trucks
Date
3.2018
Group
No.
284 065
Release
Page
01
1(7)
Engine Control Module (ECM) and
Aftertreatment Control Module (ACM),
Reprogramming
VN, VAH, VHD
FSB 284-065, Engine Control Module (ECM) and
Aftertreatment Control Module (ACM),
Reprogramming
(March 2018)
Information
Software updates with enhancements are available for the engine control module (ECM) and
aftertreatment control module (ACM) for VOLVO D11, D13 and D16 engines on OBD2016
vehicles built from January 1, 2016 to December 31, 2016.
Follow the reprogramming procedure in the following order as outlined in this document:
•
•
USA141496218
ECM reprogramming
ACM reprogramming
PV729-FSB284-065_V
Volvo Trucks North America
Field Service Bulletin
Date
3.2018
Group
No.
Release
284
065
01
The software updates address the following Diagnostic Trouble Codes (DTCs):
•
•
•
•
•
•
•
•
•
•
•
•
P026C - Fuel Injector, Low Mass Flow
P0422 – Catalyst 2 Efficiency Below Threshold (Bank 1)
P0507 – Idle Engine Speed Rationality: Idle Speed High
P10FE – DPF Restriction – Soot Accumulation Moderately High (Bank 1)
P208E – Aftertreatment Reagent Dosing Valve Clogged
P226C – Boost Pressure Slow Response
P226D – Particulate Filter Deteriorated/Missing Substrate Bank 1
P24A0 – Closed Loop DPF Regeneration Control at Limit – Temperature Too Low
P24A4 – DPF Restriction – Soot Accumulation Too High (Bank 1)
P2459 – Diesel Particulate Filter Regeneration Frequency (Bank 1)
P249C – Excessive Time To Enter Closed Loop Reductant Injection Control
P249F – Excessive Time to Enter Closed Loop DPF Regeneration Control
Check the current main software for ECM and ACM to determine the action required as
shown in the table below.
Action Required
ECM
Main Software
Action Required
D11/ D13
Equal or Less Than
22898389
Update to Latest Software
D16
Equal or Less Than
23169815
Update to Latest Software
ACM
Main Software
Action Required
D11/ D13 / D16
Equal or Less Than
22825019
Update to Latest Software
Page
2(7)
Volvo Trucks North America
Field Service Bulletin
Date
3.2018
Group
No.
Release
284
065
01
Required Tools
Premium Tech Tool (PTT) version 2.06.35 or higher
VOCOM Diagnostic Connector 88890304
Communication Interface 88890300
Note: Using other interfaces may affect programming speed.
Note: Check Premium Tech Tool version by clicking on Help tab and then click on “About
Tech Tool”.
Software Update Procedure
You must read and understand the precautions and guidelines in Service Information,
group 20, "General Safety Practices, Engines" before performing this procedure. If you are
not properly trained and certified in this procedure, ask your supervisor for training before
you perform it.
DANGER
Do not attempt to repair or service this vehicle without having sufficient training, the
correct service literature and the proper tools. Failure to follow this could make the vehicle
unsafe and lead to serious personal injury or death.
1 Park the vehicle on a level surface.
2 Apply the parking brake.
3 Place the transmission in neutral or park.
4 Install the wheel chocks.
W7086748
5 Connect Premium Tech Tool (PTT) to the vehicle diagnostics connector using the 16 pin
OBD cable 88890304 and Communication Interface 88890300. Connect the PC to a
functional LAN or modem connection and a 120 Volt AC source.
Page
3(7)
Volvo Trucks North America
Field Service Bulletin
Date
3.2018
Group
No.
Release
284
065
01
6 Turn the ignition switch “ON”.
7 Log in to PTT and Identify Vehicle is displayed.
8 Once the vehicle has been identified, enter the Work Order Number information, then
click Start Work.
W2115477
9 From the Main Menu select Program and then Program Electronic Control Unit 1700-0803-39. Then click Start.
W2115478
Page
4(7)
Volvo Trucks North America
Field Service Bulletin
Date
3.2018
Group
No.
Release
284
065
01
10 Select Engine Control Module (EMS).
W2115479
11 Select Program to update the ECM with the latest software.
W2115480
Page
5(7)
Volvo Trucks North America
Field Service Bulletin
Date
3.2018
Group
No.
Release
284
065
01
12 Certain conditions must be met to continue with programming: battery voltage above 10v,
parking brake applied, and ignition key in ON position with engine not running. When all
conditions have been met, click Continue to proceed with programming.
W2115481
13 Select “I accept” to agree to the terms and press continue to proceed.
Note: In the United States and Canada, the programing is NOT chargeable. An invoice
will not be generated.
W2115482
Page
6(7)
Volvo Trucks North America
Field Service Bulletin
Date
3.2018
Group
No.
Release
284
065
01
14 When programming is complete, click Exit to return to Main Menu to program the ACM.
15 When all programing is complete, clear any diagnostic trouble codes (DTC) and Finish
Work.
16 Remove the wheel chocks.
W7086759
Reimbursement
This repair may be eligible for reimbursement if a
product failure was experienced within time and mileage
limits of the applicable Warranty coverage.
Reimbursement is obtained via the normal claim
handling process.
UCHP
Reimbursement
Claim Type (used only when uploading from the Dealer
Bus. Sys.)
W
Labor Code
Primary Labor Code (Engine Control Module (ECM) and
Aftertreatment Control Module (ACM), Reprogramming)
2841-22-09-17
0.4 hrs.
Causal Part
3092091
VOLVO Trucks North America reserves the right to make any changes in design or to make
additions to or upon its products without incurring any obligations to install the same on
vehicles previously built.
Page
7(7)