S-SB-0003-13 Rev
Service Bulletin Details
Public Details for: S-SB-0003-13 Rev
2013 pre-delivery service cheek sheet
- 2013 -
Models from 2013
2013 SCION XB |
xB 01 Install Short Pin (see page 2) .......................................... FUNCTIONAL OPERATION Apply parking brake and cycle ignition “IG-ON”; place gear selector in reverse; turn on lights and rear defogger. Unlock doors; release fuel door. 01 02 03 04 05 06 07 08 09 10 11 Check dome, courtesy, map, and sun visor lights* ......... Check warning/indicator lights, gauges, and horn ........... Check windshield wipers and washers ............................ Check headlights, instrument lights, turn signals, dimmer switch, emergency flashers, and brake lights .................. Check inside/outside rear view mirror operation/ adjustment ....................................................................... Check cigarette lighter* and power outlets* ..................... Check audio/navigation* systems, set SSP to xB, and set clock ........................................................................... Install shift-lock override button cover ............................. Check rear entertainment system operation* .................. Check that the electroluminescent dash illuminates when door is opened** ..................................................... Check that the shift knob illuminates**……………………. WALKAROUND INSPECTION Start at left front door. Check window and door lock operation (from master power switch, if equipped). Continue around vehicle in a counterclockwise direction checking each door and window operation, child door locks, seat belts, interior condition, all lights, luggage compartment contents. Finish by checking headlight aim and continue into UNDER HOOD checks. 01 Check power window operation ....................................... 02 Check door and door lock operation, including each wireless remote control/theft deterrent system* ............... 03 Check that engine starts with all keys .............................. 04 Check that child safety door locks are in normal (unlocked) position* ......................................................... 05 Check seats and seat belt operation ................................ 06 Check rear defogger/rear view mirror defogger* .............. 07 Check side marker, tail, backup, and license plate lights. 08 Check luggage compartment light* & trim appearance ... 09 Adjust spare tire pressure and check jack and tool installation ....................................................................... 10 Check headlight aim ........................................................ 11 Check that front and rear exterior Scion badges illuminate after unlocking vehicle**……………………….. UNDER HOOD 01 02 03 04 05 Check engine oil and ATM* fluid levels ........................... Check brake and clutch* fluid levels ................................ Check engine coolant level ............................................. Check windshield washer fluid level ............................... Check battery state-of-charge using Digital Battery System Analyzer (SOC Reading: ___________%) ..... 06 Inspect for fuel, oil, coolant, and other fluid leaks ............ * Inspect or install when equipped/required. ** For Scion Series 10 vehicles only. UNDER VEHICLE (ON HOIST) OK June 2013 Rev1 Adjust/ Repair OK BEFORE INSPECTION Adjust/ Repair 2013 PRE-DELIVERY SERVICE CHECK SHEET 01 Remove disc brake anti-corrosion wheel film*............ 02 Inspect tires for defects/damage (including spare tire) .... 03 Activate Tire Pressure Warning System (TPWS) (see page 2) ............................................................................ 04 Install wheel covers/caps/spare tire wheel covers* .......... 05 Inspect for fuel, oil, coolant, and other fluid leaks ............ 06 Visually check bolts and nuts on chassis and powertrain for looseness.................................................................... 07 Inspect under the vehicle for damage, rust, etc. .............. 08 Install rubber body plugs (stored in glove box or center console) .......................................................................... ROAD TEST A complete road test helps assure customer satisfaction. Drive vehicle over a variety of road surfaces and driving conditions. Check for unusual noise and driving performance. Enter Odometer Reading Reading Before Test: _______________ Reading After Test: ________________ 01 02 03 04 05 06 07 08 09 10 11 Check cold engine operation............................................ Check engine operation during warm-up ......................... Check engine at normal operating temperature ............... Check clutch or automatic transmission operation ........... Check brake and parking brake operation ....................... Check steering operation and off-center/vehicle pull/flutter ......................................................................... Inspect for abnormal noise and vibration ......................... Inspect for squeaks and rattles ........................................ Check front and rear* heater and A/C operation .............. Check speedometer operation ........................................ Check cruise control operation* ....................................... FINAL INSPECTION AND CLEANING 01 Remove interior protective covers, unnecessary labels, tags, etc. (Remove just before delivery to customer) ....... 02 Verify floor mat application and install using retaining clips* ............................................................... 03 Visually inspect all interior parts for installation, damage, fit, dirt, etc. ........................................................ 04 Remove Rapgard™ and clear protective bumper film* .... 05 Wash and clean vehicle ................................................... 06 Inspect paint finish for scratches, chips, rust, dents, damage, etc. .................................................................... 07 Inspect exterior body parts for proper installation, damage, rust, etc. ............................................................ 08 Place oil change sticker on inside of windshield, top left corner ......................................................................... 09 Place Owner’s Guide and first aid kit portfolio* in glove box ..................................................................... 10 Install front license plate and mounting bracket (see page 2) ............................................................................ 11 Perform Techstream Health Check ................................. Completion and retention of this from is required to comply with Toyota’s Warranty Policy. TECHNICIAN’S SIGNATURE SERVICE MANAGER’S SIGNATURE NAME (PLEASE PRINT) NAME (PLEASE PRINT) Date Dealer Name Dealer Code We hereby certify that all items on this form have been checked and corrected for proper operation as required. Vehicle Identification Number (Sticker) SHORT PIN INSTALLATION To minimize battery discharge the Short Pin has been removed and is stored in the engine compartment Relay Block. Install the Short Pin and confirm all related DTCs are cleared. 2 DTC Clearing Procedure 1. 2. 3. 4. Connect Techstream. Cycle the ignition switch to the “IG-ON” position. Using Techstream, check any other codes being output. Erase DTCs (B1650 and B1794) and Freeze Frame Data. 1 NOTE If any DTCs besides B1650 and B1794 appear, repair the applicable system according to the Repair Manual. 1 Remove This Short Pin 2 Install Short Pin Here TPWS ACTIVATION & INITIALIZATION Activation Procedure 1. Connect Techstream. 2. Cycle the IG switch to the “IG-ON” position and check that the Low Tire Pressure Warning Light blinks for 1 minute and then remains illuminated. 3. Press or remove the valve core to reduce the tire inflation pressure rapidly by 6 psi (0.4 kfg/cm², 40 kPA), or more, within 30 seconds. 4. Check that the Low Tire Pressure Warning Light goes OFF after all the TPWS sensors are activated. 5. Using Techstream, check for DTCs (C2111-C2114). If no DTCs are stored, continue to Initialization procedure. If these DTCs are stored, repeat step 3. Initialization Procedure Refer to the Repair Manual for the Initialization procedure. Please note the spare tire does not have a TPWS sensor. NOTE To adjust tire pressure correctly when outside temperature is significantly colder or warmer than shop temperature, follow the procedures outlined in Service Bulletin No. S-SB-0001-12, “Tire Inflation Pressure Compensation and Adjustment.” FRONT LICENSE PLATE & MOUNTING BRACKET INSTALLATION For states that require a front license plate, please install per this procedure. The bracket and self-tapping screws are stored in the luggage compartment. Installation Procedure 1. Insert the front license plate into the mounting bracket. 2. Attach the hooks of the mounting bracket to the upper lip of the air intake and rotate the bracket upwards and hold in place. NOTE The mounting bracket should snap securely onto the bumper cover. 4. Align the installation holes on the mounting bracket and front license plate with the dimples on the front bumper. 5. Screw in the 2 self-tapping screws directly into the dimples to install the front license plate and mounting bracket. NOTICE • Do NOT pre-drill holes into the bumper. • Do NOT over-tighten the self-tapping screws. 2 4 3 3 4 2 1 1 Mounting Bracket 2 Hooks 3 Air Intake 4 Rotate Bracket 1 1 Self-tapping Screws 2 Dimples 3 License Plate 4 Mounting Bracket