S-SB-0032-12 Rev

Service Bulletin Details

Public Details for: S-SB-0032-12 Rev

Some 2013 model year fr-s vehicles may exhibit a mil ?On? Condition with one of the following diagnostic trouble codes (dtcs): P0017 or P0019 (?Cam sensor correlation?). The engine control module/ecm (sae term: powertrain control module/ pc


- 2013 -

Models from 2013
2013 SCION FR-S
S-SB-0032-12
Rev1
November 19, 2012
MIL "ON" DTC P0017 or P0019
Service
Category
Engine/Hybrid System
Section
Engine Control
USA
Market
Applicability
YEAR(S)
MODEL(S)
2013
FR-S
ADDITIONAL INFORMATION
REVISION NOTICE
January 16, 2013 Rev1:
• A Service Bulletin link has been updated in the Repair Procedure.
Any previous printed versions of this bulletin should be discarded.
Introduction
Some 2013 model year FR-S vehicles may exhibit a MIL “ON” condition with one of the following
Diagnostic Trouble Codes (DTCs): P0017 or P0019 (“Cam Sensor Correlation”). The Engine Control
Module/ECM (SAE term: Powertrain Control Module/ PCM) logic has been revised to address
this condition. Use the following repair procedure to determine if ECM (PCM) replacement or
reprogramming is required.
Production Change Information
This bulletin applies to vehicles produced BEFORE the Production Change Effective VIN shown
below.
MODEL
PLANT
PRODUCTION CHANGE EFFECTIVE VIN
FR-S
GUNMA
JF1ZNAA1#D#710670
Calibration Information
MODEL
TRANSMISSION
PREVIOUS CALIBRATION ID
NEW CALIBRATION ID
AT
ZA1J900D
ZA1J700D
ZA1JA00D
MT
ZA1J900C
ZA1J700C
ZA1JA00C
FR-S
© 2013 Toyota Motor Sales, USA
Page 1 of 6
Rev1
S-SB-0032-12
November 19, 2012
Page 2 of 6
MIL "ON" DTC P0017 or P0019
Warranty Information
OP CODE
DESCRIPTION
EG1218
Replace the ECM (PCM)
EG1219
Reprogram the ECM (PCM)
TIME
OFP
T1
T2
0.4
SU003-00433 (AT)
SU003-04521 (AT)
SU003-00434 (MT)
SU003-04522 (MT)
8A
99
APPLICABLE WARRANTY
• This repair is covered under the Toyota Federal Emission Warranty. This warranty is in effect
for 96 months or 80,000 miles, whichever occurs first, from the vehicle’s in-service date.
• Warranty application is limited to occurrence of the specified condition described in this
bulletin.
Parts Information
BEFORE ordering any of the parts listed below, refer to Repair Procedure to determine if
replacement or reprogramming is needed.
TRANS
PREVIOUS PART NUMBER
CURRENT PART NUMBER
AT
SU003-00433
SU003-04521
SU003-04567
MT
SU003-00434
SU003-04522
SU003-04568
–
00451-00001-LBL
Same
PART NAME
QTY
1*
Computer, Engine Control
1*
Authorized Modification Labels
1**
* Order ONLY for ECM replacement.
** Order ONLY for ECM reprogramming.
NOTE
Authorized Modification Labels may be ordered in packages of 25 from the Materials Distribution
Center (MDC) through Dealer Daily – Dealer Support Materials Orders.
© 2013 Toyota Motor Sales, USA
Rev1
S-SB-0032-12
November 19, 2012
Page 3 of 6
MIL "ON" DTC P0017 or P0019
Required Tools & Equipment
REQUIRED EQUIPMENT
TIS Techstream*
or
Techstream Lite
SUPPLIER
PART NUMBER
QTY
ADE
TSPKG1
or
TSLITEDLR01
1
NOTE: Software version 7.31.003 or later is required.
NOTE
• Additional Techstream units may be ordered by calling Approved Dealer
Equipment (ADE) at 1-800-368-6787.
• The Diagnostic Tester is NOT recommended for flash reprogramming
with this calibration file. Please use TIS Techstream or an approved
J2534 interface to perform this update. Visit techinfo.toyota.com for more
information regarding J2534 reprogramming.
SPECIAL SERVICE TOOLS (SST)
PART NUMBER
QTY
GR8 Battery Diagnostic Station*
00002-MCGR8
1
NOTE
Additional SSTs may be ordered by calling 1-800-933-8335.
* Essential SST.
© 2013 Toyota Motor Sales, USA
Rev1
S-SB-0032-12
November 19, 2012
Page 4 of 6
MIL "ON" DTC P0017 or P0019
Repair Procedure
1. Confirm DTC P0017 or P0019 is set.
2. Using the Techstream Utility “VVT Initial Position
Learning Value Display”, confirm the VVT Ex
Initial Position Learning Value #1 and #2 are
within the range.
Figure 1.
.
3. Is the value within range?
RANGE (IN DEGREES)
VVT Ex Initial Position Learning Value
MINIMUM
MAXIMUM
85.0
95.0
• YES — Proceed to step 4 (Reprogram the ECM).
• NO — Proceed to step 5 (Replace the ECM).
© 2013 Toyota Motor Sales, USA
Rev1
S-SB-0032-12
November 19, 2012
Page 5 of 6
MIL "ON" DTC P0017 or P0019
Repair Procedure (Continued)
4. Reprogram the ECM.
A. Check for the Authorized Modifications Label affixed to the vehicle in the location shown in
Figure 2. Confirm if the ECM (PCM) calibration has been updated. If the calibration ID listed
is NOT the latest ECM (PCM) calibration — go to step 4.B.
Figure 2. Location of Authorized Modifications Label on 2013 FR-S
1
Replacement ECM (PCM) Part Number (i.e.,
SU003-04567)
2
New Calibration ID(s) (i.e., ZA1JA00D)
3
Dealer Code
4
Date Completed
5
This SB Number
© 2013 Toyota Motor Sales, USA
Rev1
S-SB-0032-12
November 19, 2012
Page 6 of 6
MIL "ON" DTC P0017 or P0019
Repair Procedure (Continued)
B. Flash reprogram the ECM (PCM).
NOTE
• The GR8 Battery Diagnostic Station MUST be used in Power Supply Mode to maintain
battery voltage at 13.5 volts while flash reprogramming the vehicle.
• For details on how to use the GR8 Battery Diagnostic Station, refer to the GR8
Instruction Manual located on the Technical Information System (TIS), Diagnostics –
Tools & Equipment – Battery Diagnostics.
Follow the procedures outlined in Service Bulletin No. S-SB-0003-10, “Techstream ECU Flash
Reprogramming Procedure”, and flash the ECM (PCM) with the NEW calibration file update.
C. Install the Authorized Modifications Label.
(1) Using a permanent marker, enter the following information on the label:
• ECM part number [Refer to the Parts Information section for the CURRENT
PART NUMBER]
• Calibration ID(s) [Refer to the Calibration Identification Chart for the NEW
CALIBRATION ID]
• Dealer Code
• Repair Date
• Change Authority [This bulletin number]
(2) Affix the Authorized Modifications Label to the vehicle at the location shown in
Figure 2. The Authorized Modifications Label is available through the MDC,
P/N 00451-00001-LBL.
D. Start the engine and warm it up to normal operating temperature and test drive to confirm
proper vehicle operation.
5. Replace the ECM (PCM).
Refer to the Technical Information System (TIS), 2013 model year FR-S Repair Manual:
• Engine/Hybrid System – Engine Control – “FA20 Engine Control: ECM: Removal /
Installation”
© 2013 Toyota Motor Sales, USA


© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.