T-SB-0205-12

Service Bulletin Details

Public Details for: T-SB-0205-12

Some 2010 ? 2011 model year camry vehicles equipped with the 2ar-fe engine and some 2009 ? 2013 model year venza vehicles equipped with the 1ar-fe engine may exhibit one or more of the following conditions: a/c inoperative while the vehicl


- 2013 - 2012 - 2011 - 2010 - 2009 -

Models from 2013
2013 TOYOTA VENZA
Models from 2012
2012 TOYOTA VENZA
Models from 2011
2011 TOYOTA CAMRY
2011 TOYOTA VENZA
Models from 2010
2010 TOYOTA CAMRY
2010 TOYOTA VENZA
Models from 2009
2009 TOYOTA VENZA 
T-SB-0205-12
October 22, 2012
A/C Inoperative and/or High Engine Temperature at a Stop
Service
Category
Engine/Hybrid System
Section
Cooling
Market
USA
Applicability
YEAR(S)
MODEL(S)
ADDITIONAL INFORMATION
2010 – 2011
Camry
Engine(s): 2AR
VDS(s): BF3EK
2009 – 2013
Venza
VDS(s): BA3BB, BE11A, ZA3BB
NOTE
This bulletin only applies to vehicles that are NOT equipped with the Tow Package.
Introduction
Some 2010 – 2011 model year Camry vehicles equipped with the 2AR-FE engine and some
2009 – 2013 model year Venza vehicles equipped with the 1AR-FE engine may exhibit one or more
of the following conditions:
• A/C inoperative while the vehicle is stopped.
• Rising engine temperature while the vehicle is stopped.
Production Change Information
This bulletin applies to:
• ALL 2010 – 2011 model year Camry vehicles.
• ALL 2009 – 2012 model year Venza vehicles.
• 2013 model year Venza vehicles produced BEFORE the Production Change Effective VINs
shown below.
MODEL
PLANT
ENGINE
Venza
TMMK Line 2
1AR-FE
DRIVETRAIN
PRODUCTION CHANGE EFFECTIVE VIN
2WD
4T3ZA3BB#DU067658
4WD
4T3BA3BB#DU037398
© 2013 Toyota Motor Sales, USA
Page 1 of 9
T-SB-0205-12
Page 2 of 9
October 22, 2012
A/C Inoperative and/or High Engine Temperature at a Stop
Warranty Information
OP CODE
DESCRIPTION
MODEL
TIME
EL1222
R & R Radiator Fan(s) / Recalibrate
ECM (PCM) Engine
Camry
2.2
Combo A
R & R Cooling Fan Motor (if necessary)
Venza
2.6
OFP
T1
T2
16361-0H090
16361-0H100
13
12
0.1
APPLICABLE WARRANTY
• This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months
or 36,000 miles, whichever occurs first, from the vehicle’s in-service date.
• Warranty application is limited to occurrence of the specified condition described in this
bulletin.
Required Tools & Equipment
REQUIRED EQUIPMENT
TIS Techstream*
or
Techstream Lite
SUPPLIER
PART NUMBER
QTY
ADE
TSPKG1
or
TSLITEDLR01
1
NOTE: Software version 7.20.041 or later is required.
NOTE
• Additional Techstream units may be ordered by calling Approved Dealer
Equipment (ADE) at 1-800-368-6787.
• The Diagnostic Tester is NOT recommended for flash reprogramming
with this calibration file. Please use TIS Techstream or an approved
J2534 interface to perform this update. Visit techinfo.toyota.com for more
information regarding J2534 reprogramming.
SPECIAL SERVICE TOOLS (SST)
PART NUMBER
QTY
GR8 Battery Diagnostic Station*
00002-MCGR8
1
NOTE
Additional SSTs may be ordered by calling 1-800-933-8335.
* Essential SST.
© 2013 Toyota Motor Sales, USA
T-SB-0205-12
Page 3 of 9
October 22, 2012
A/C Inoperative and/or High Engine Temperature at a Stop
Parts Information
MODEL
Camry
PART NAME
PREVIOUS PART NUMBER
CURRENT PART NUMBER
QTY
89661-06N70
89661-06N71
–
89661-06N80
89661-06N81
–
89661-06J13
89661-06J14
–
89661-06J43
89661-06J44
–
Computer, Engine Control
(ECM/PCM)
–
89661-06J22
89661-06J23
89661-0T052
89661-0T053
–
89661-0T062
89661-0T063
–
89661-0T110
89661-0T111
–
89661-0T120
89661-0T121
–
–
16361-0H090
16361-0V400
Fan
1
–
16361-0H100
16361-0V410
Fan, No. 2
1
–
16363-0H010
Same
Motor, Cooling Fan
1*
–
16363-0H070
Same
Motor, Cooling Fan, No.2
1*
–
00272-SLLC2
Same
Super Long Life Coolant
As Needed
–
00451-00001-LBL
Same
Authorized Modification Labels
1
Venza
* Replace Cooling Fan Motor ONLY if necessary. Refer to Repair Procedure.
NOTE
• The ECM (PCM) should NOT be replaced as part of the repair procedure.
• Authorized Modification Labels may be ordered in packages of 25 from the Materials
Distribution Center (MDC) through Dealer Daily – Dealer Support Materials Orders.
© 2013 Toyota Motor Sales, USA
T-SB-0205-12
October 22, 2012
Page 4 of 9
A/C Inoperative and/or High Engine Temperature at a Stop
Calibration Information
MODEL
TRANS
EMISSION
SPECIFICATION
MODULE
PREVIOUSCALIBRATION ID
NEW CALIBRATION ID
333G5000
333B6000
ECM
333B6100
PZEV
333B6400
333B6200
333B6300
ECT
AT
895363315000
895363319000
895363328000
333G4000
2010–2011
Camry
333B5000
ECM
333B5100
333B5400
333B5200
333B5300
ULEV2
ECT
895363315000
895363319000
895363328000
30669000
MT
30669100
ECM
30669300
30669200
MODEL
MODEL YEAR
DRIVE
PREVIOUS CALIBRATION ID
NEW CALIBRATION ID
30T03000
FWD
30T06000
30T06100
30T06300
30T06200
2009–2012
30T04000
Venza
4WD
30T07000
30T07100
30T07300
30T07200
2013
FWD
30T11000
30T11100
4WD
30T12000
30T12100
© 2013 Toyota Motor Sales, USA
T-SB-0205-12
October 22, 2012
Page 5 of 9
A/C Inoperative and/or High Engine Temperature at a Stop
Repair Procedure
1. Confirm the condition per the Introduction.
2. Inspect the radiator cooling fan blades for
separation from the cooling fan motor.
Figure 1.
.
Are the fan blades separated?
• YES — Go to step 3.
• NO — This bulletin does NOT apply.
Continue diagnosis per the applicable Repair
Manual.
3. Replace the cooling fans.
Refer to the Technical Information System (TIS), applicable model and model year Repair
Manual:
• 2010 Camry:
Engine/Hybrid System – Cooling – “2AR-FE Cooling: Radiator: Cooling Fan Motor:
Removal / Installation”
• 2011 Camry:
Engine/Hybrid System – Cooling – “2AR-FE Cooling: Radiator: Cooling Fan Motor:
Removal / Installation”
• 2009 Venza:
Engine/Hybrid System – Cooling – “1AR-FE Cooling: Cooling Fan Motor: Removal /
Installation”
• 2010 Venza:
Engine/Hybrid System – Cooling – “1AR-FE Cooling: Cooling Fan Motor: Removal /
Installation”
• 2011 Venza:
Engine/Hybrid System – Cooling – “1AR-FE Cooling: Cooling Fan Motor: Removal /
Installation”
• 2012 Venza:
Engine/Hybrid System – Cooling – “1AR-FE Cooling: Cooling Fan Motor: Removal /
Installation”
• 2013 Venza:
Engine/Hybrid System – Cooling – “1AR-FE Cooling: Cooling Fan Motor: Removal /
Installation”
© 2013 Toyota Motor Sales, USA
T-SB-0205-12
October 22, 2012
Page 6 of 9
A/C Inoperative and/or High Engine Temperature at a Stop
Repair Procedure (Continued)
4. Inspect the cooling fan motors by spinning the shaft by hand checking for any abnormalities, and
then check the amperage draw according to the Repair Manual.
Refer to TIS, applicable model and model year Repair Manual:
• 2010 Camry:
Engine/Hybrid System – Cooling – “2AR-FE Cooling: Cooling Fan Motor: On-vehicle
Inspection”
• 2011 Camry:
Engine/Hybrid System – Cooling – “2AR-FE Cooling: Cooling Fan Motor: On-vehicle
Inspection”
• 2009 Venza:
Engine/Hybrid System – Cooling – “1AR-FE Cooling: Cooling Fan Motor: On-vehicle
Inspection”
• 2010 Venza:
Engine/Hybrid System – Cooling – “1AR-FE Cooling: Cooling Fan Motor: On-vehicle
Inspection”
• 2011 Venza:
Engine/Hybrid System – Cooling – “1AR-FE Cooling: Cooling Fan Motor: On-vehicle
Inspection”
• 2012 Venza:
Engine/Hybrid System – Cooling – “1AR-FE Cooling: Cooling Fan Motor: On-vehicle
Inspection”
• 2013 Venza:
Engine/Hybrid System – Cooling – “1AR-FE Cooling: Cooling Fan Motor: On-vehicle
Inspection”
5. If there are any abnormalities found with the cooling fan motors, replace the cooling fan motors.
Refer to TIS, applicable model and model year Repair Manual:
• 2010 Camry:
Engine/Hybrid System – Cooling – “2AR-FE Cooling: Radiator: Cooling Fan Motor:
Removal / Installation”
• 2011 Camry:
Engine/Hybrid System – Cooling – “2AR-FE Cooling: Radiator: Cooling Fan Motor:
Removal / Installation”
• 2009 Venza:
Engine/Hybrid System – Cooling – “1AR-FE Cooling: Cooling Fan Motor: Removal /
Installation”
© 2013 Toyota Motor Sales, USA
T-SB-0205-12
October 22, 2012
Page 7 of 9
A/C Inoperative and/or High Engine Temperature at a Stop
Repair Procedure (Continued)
• 2010 Venza:
Engine/Hybrid System – Cooling – “1AR-FE Cooling: Cooling Fan Motor: Removal /
Installation”
• 2011 Venza:
Engine/Hybrid System – Cooling – “1AR-FE Cooling: Cooling Fan Motor: Removal /
Installation”
• 2012 Venza:
Engine/Hybrid System – Cooling – “1AR-FE Cooling: Cooling Fan Motor: Removal /
Installation”
• 2013 Venza:
Engine/Hybrid System – Cooling – “1AR-FE Cooling: Cooling Fan Motor: Removal /
Installation”
6. Check for the Authorized Modifications Label affixed to the vehicle in the location shown in
Figures 2 and 3. Confirm if the ECM (PCM) calibration has been updated. If the calibration ID
listed is NOT the latest ECM (PCM) calibration — go to step 7.
Figure 2. Location of Authorized Modifications Label on 2010 – 2011 Camry
1
2
3
4
5
1
Replacement ECM (PCM) Part Number (i.e.,
89661-06N71)
2
New Calibration ID(s) (i.e., 333B5400)
3
Dealer Code
4
Date Completed
5
This SB Number
© 2013 Toyota Motor Sales, USA
T-SB-0205-12
October 22, 2012
Page 8 of 9
A/C Inoperative and/or High Engine Temperature at a Stop
Repair Procedure (Continued)
Figure 3. Location of Authorized Modifications Label on 2009 – 2013 Venza
1
Replacement ECM (PCM) Part Number (i.e.,
89661-0T053)
2
New Calibration ID(s) (i.e., 30T06300)
3
Dealer Code
4
Date Completed
5
This SB Number
7. Flash reprogram the ECM (PCM).
NOTE
• The GR8 Battery Diagnostic Station MUST be used in Power Supply Mode to maintain
battery voltage at 13.5 volts while flash reprogramming the vehicle.
• For details on how to use the GR8 Battery Diagnostic Station, refer to the GR8 Instruction
Manual located on the Technical Information System (TIS), Diagnostics – Tools &
Equipment – Battery Diagnostics.
Follow the procedures outlined in Service Bulletin No. T-SB-0064-10, “Techstream ECU Flash
Reprogramming Procedure”, and flash the ECM (PCM) with the NEW calibration file update.
© 2013 Toyota Motor Sales, USA
T-SB-0205-12
October 22, 2012
Page 9 of 9
A/C Inoperative and/or High Engine Temperature at a Stop
Repair Procedure (Continued)
8. Install the Authorized Modifications Label.
A. Using a permanent marker, enter the following information on the label:
• ECM part number [Refer to the Parts Information section for the CURRENT PART
NUMBER]
• Calibration ID(s) [Refer to the Calibration Identification Chart for the NEW
CALIBRATION ID]
• Dealer Code
• Repair Date
• Change Authority [This bulletin number]
B. Affix the Authorized Modifications Label to the vehicle at the location shown in
Figures 2 and 3. The Authorized Modifications Label is available through the MDC,
P/N 00451-00001-LBL.
9. Verify the vehicle operates properly and the A/C functions normally.
© 2013 Toyota Motor Sales, USA

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.