T-SB-0029-14 Rev

T-SB-0029-14
Rev1
April 17, 2014
Floor Mat Installation During PDS
Service
Category
General
Section
Pre-Delivery Service
Market
USA
Applicability
YEAR(S)
MODEL(S)
2015 – 2016
4Runner, Avalon,
Avalon HV, Camry,
Camry HV, Corolla,
Highlander, Highlander
HV, Land Cruiser,
Prius, Prius C, Prius
PHV, Prius V, RAV4,
Sequoia, Sienna,
Tacoma, Tundra,
Venza, Yaris
2016
Mirai
ADDITIONAL INFORMATION
REVISION NOTICE
August 19, 2015 Rev1:
• Applicability has been updated to include 2016 model year Toyota vehicles.
Any previous printed versions of this bulletin should be discarded.
Introduction
2015 – 2016 model year vehicles are equipped with driver’s side floor mat retaining clips to
secure the floor mat in the correct position. In addition, some models may utilize retaining clips for
passenger side and rear seat floor mats as well. Follow the appropriate installation procedure to
attach the driver’s side, and if applicable, the passenger’s side and rear seat floor mats to the vehicle
carpet using the floor mat retaining clips during Pre-Delivery Service (PDS).
© 2015 Toyota Motor Sales, USA
Page 1 of 9
Rev1
T-SB-0029-14
April 17, 2014
Page 2 of 9
Floor Mat Installation During PDS
Introduction (Continued)
CAUTION
• Always verify the floor mat to assure it is designed specifically for the model and model year it
is being installed in.
• ONLY use floor mats that can be retained using the retaining clips. All OEM Toyota floor mats
are specifically designed to fit correctly and be retained using the retaining clips.
• Make sure the floor mat is properly placed on the vehicle carpet and secured with the retaining
clips. If the driver side floor mat is NOT properly placed and secured, it could slip and interfere
with the movement of the pedals during driving and may cause an accident.
• Verify the operation of the accelerator, brake, and clutch (if equipped) pedals and clearance
to the mat.
• NEVER install more than one floor mat at a time in the driver’s seating position.
• If applicable, any secondary set of floor mats (based upon customer preference, such as the
all weather floor mats or other floor mats) MUST be placed in the trunk with all the packaging
material intact. Do NOT install the secondary mat on top of the primary floor mat already
installed in the driver’s seating position.
Warranty Information
OP CODE
DESCRIPTION
TIME
OFP
T1
T2
N/A
Not Applicable to Warranty
–
–
–
–
© 2015 Toyota Motor Sales, USA
Rev1
T-SB-0029-14
April 17, 2014
Page 3 of 9
Floor Mat Installation During PDS
Installation Procedure: Hook Style
1. Verify that the driver, and if applicable, passenger side and rear seat, floor mats are for the
correct model and model year they are being installed in.
2. Attach the driver, and if applicable, passenger side and rear seat, floor mats to the vehicle
carpet using the retaining clips. Secure the mat by inserting the retaining clips through the
grommet holes.
Figure 1.
0000000000
0000000000
0000000000
3
0000
000
0000000000
0000
000
0000000000
0000000000
0000
0000000000
0000000000
1
2
0000000000
0000
0000000000
0000000000
0000
1
Retaining Clips
2
Grommets
3
© 2015 Toyota Motor Sales, USA
Correct Installation
Rev1
T-SB-0029-14
April 17, 2014
Page 4 of 9
Floor Mat Installation During PDS
Installation Procedure: Hook Style (Continued)
3. Verify proper installation.
NOTE
If applicable, DO NOT remove the beige “Caution” tag from the floor mat. This should only be
removed by the customer.
Figure 2.
© 2015 Toyota Motor Sales, USA
Rev1
T-SB-0029-14
April 17, 2014
Page 5 of 9
Floor Mat Installation During PDS
Installation Procedure: Hook Style with Locking Clip
1. Verify that the driver, and if applicable, passenger side and rear seat, floor mats are for the
correct model and model year they are being installed in.
2. Attach the retention clip to the floor by inserting the retention clip claws into the floor eyelet.
Figure 3.
5
B
B
1
4
A
A
B
3
2
1
Retention Clip
5
Cross-sectional Diagram
2
Front of Vehicle
A
Retention Clip Claw
3
Retention Clip Eyelet on Vehicle Floor
B
Locking Clip
4
Seat
© 2015 Toyota Motor Sales, USA
Rev1
T-SB-0029-14
April 17, 2014
Page 6 of 9
Floor Mat Installation During PDS
Installation Procedure: Hook Style with Locking Clip (Continued)
3. To lock the retention clip in place, insert the
locking clip of the retention clip into the
designated hole.
Figure 4..
1
1
4. Align the floor mat holes with the retention clip
hooks and place the floor mat holes onto the
retention clip hooks.
Locking Clip
Figure 5..
1
2
3
1
Retention Clip Eyelet on Floor Mat
2
Retention Clip
3
Front
© 2015 Toyota Motor Sales, USA
Rev1
T-SB-0029-14
April 17, 2014
Page 7 of 9
Floor Mat Installation During PDS
Installation Procedure: Hook Style with Locking Clip (Continued)
5. Verify proper installation.
NOTE
If applicable, DO NOT remove the beige “Caution” tag from the floor mat. This should only be
removed by the customer.
Figure 6.
© 2015 Toyota Motor Sales, USA
Rev1
T-SB-0029-14
April 17, 2014
Page 8 of 9
Floor Mat Installation During PDS
Installation Procedure: Pre-installed Knob Style
1. Verify that the driver, and if applicable, passenger side and rear seat, floor mats are for the
correct model and model year they are being installed in.
2. Align the floor mat holes with the retention clip
knobs and place the floor mat holes onto the
retention clip knobs.
Figure 7.
.
1
2
3
3. Turn the retention clip knobs a quarter of a turn to
lock in place and verify the “triangle” marks on the
retention clip knobs and floor mat are aligned.
1
Retention Clip Eyelet on Floor Mat
2
Retention Clip
3
Front of Vehicle
Figure 8.
.
3
1
1
Twist Knob
2
Knob in Locked Position
3
Align “Triangle” Marks
© 2015 Toyota Motor Sales, USA
2
Rev1
T-SB-0029-14
April 17, 2014
Page 9 of 9
Floor Mat Installation During PDS
Installation Procedure: Pre-installed Knob Style (Continued)
4. Verify proper installation.
Figure 9.
NOTE
If applicable, DO NOT remove the yellow
“Caution” tag from the floor mat. This should
only be removed by the customer.
© 2015 Toyota Motor Sales, USA
.