T-SB-0163-13 Rev

T-SB-0163-13
Rev1
November 6, 2013
Entune/Navigation Software Update Process for Display
Audio (Non-HDD Type)
Service
Category
Audio/Visual/Telematics
Section
Navigation/Multi Info Display
Market
USA
Applicability
YEAR(S)
MODEL(S)
2012 – 2013
4Runner, Corolla,
RAV4, Tacoma
2013 – 2014
Avalon, Avalon HV,
Venza
2012 – 2014
Camry, Camry HV,
Prius, Prius C, Prius
PHV, Prius V
2013
Highlander, Highlander
HV
2015
Prius, Prius PHV
ADDITIONAL INFORMATION
REVISION NOTICE
August 19, 2015 Rev1:
• Applicability has been updated to include 2015 model year Prius and Prius PHV vehicles.
Any previous printed versions of this bulletin should be discarded.
SUPERSESSION NOTICE
The information contained in this bulletin supersedes SB No. T-SB-0026-12.
• Applicability has been updated to include 2014 model year vehicles.
• The software version number, the SST part number, and the Repair Procedure have been
updated.
Service Bulletin No. T-SB-0026-12 is Obsolete and any printed versions should be discarded. Be
sure to review the entire content of this bulletin before proceeding.
© 2015 Toyota Motor Sales, USA
Page 1 of 5
T-SB-0163-13
Rev1
November 6, 2013
Page 2 of 5
Entune/Navigation Software Update Process for Display Audio (Non-HDD Type)
Introduction
Use the following procedures to check and/or update the software version of Entune/Navigation for
Non-HDD Type units.
NOTE
• Non-HDD Type Navigation units have a CD slot visible on the front of the radio.
• HDD Type Navigation units have a tilt-open navigation screen and CD slot behind the screen.
Required Tools & Equipment
SPECIAL SERVICE TOOLS (SST)
USB Drive Firmware Update Harman Becker*
PART NUMBER
FILE NAME
SOFTWARE
VERSION
01032-HBEKR-15A
01032-HBEKR-15A.zip
5.1.0
* Essential SST.
MULTIMEDIA SOFTWARE FILE DOWNLOAD
The Multimedia software update file may also be downloaded directly from this Service Bulletin by
clicking on the file name in the table above. Once downloaded, the file may be extracted (unzipped)
from the “zip” folder and saved directly to a commonly-available blank USB flash drive.
For USB flash drive requirements and download instructions:
Refer to the Technical Information System (TIS): Diagnostics – Calibrations –
Reference Documents – “Multimedia Software Download Instructions”
NOTE
Additional SSTs may be ordered by calling 1-800-933-8335.
© 2015 Toyota Motor Sales, USA
T-SB-0163-13
Rev1
November 6, 2013
Page 3 of 5
Entune/Navigation Software Update Process for Display Audio (Non-HDD Type)
Warranty Information
OP CODE
DESCRIPTION
TIME
OFP
T1
T2
N/A
Not Applicable to Warranty
–
–
–
–
Software Version Check Procedure
1. Press the Setup button.
2. In the Setup menu, select General.
Figure 1.
.
3. In the General Settings menu, scroll down and
select System Information.
Figure 2.
.
4. In the System Information menu the Software
Version information is displayed (eg., 1.7.x, 1.8.4,
2.1.0, 2.2.0, 3.1.0, 3.2.0).
Figure 3..
32
© 2015 Toyota Motor Sales, USA
T-SB-0163-13
Rev1
November 6, 2013
Page 4 of 5
Entune/Navigation Software Update Process for Display Audio (Non-HDD Type)
Software Update Procedure
1. Start the vehicle or put hybrid system in Ready ON mode.
2. Turn on the radio.
3. Press the Apps button (the system will switch to the Apps main page).
4. Install USB Drive SST into vehicle’s USB slot (there will be a short pause while the software
version is read).
5. An “Update software from X.X.X to 5.1.0?”
message will be displayed.
Figure 4..
32
5
6. Select Yes.
7. A “Please do not interrupt the software update
once it has started. The engine must be
running during software update.” message will
be displayed.
Figure 5..
8. Select Confirm (the engine must be running or hybrid system in Ready ON mode during
software update).
9. The Software update will begin and the screen
will show a “Package 1 of 8” message, and
continue through 8 of 8. It will take approximately
5 minutes for the update to complete.
Figure 6.
© 2015 Toyota Motor Sales, USA
.
Rev1
T-SB-0163-13
November 6, 2013
Page 5 of 5
Entune/Navigation Software Update Process for Display Audio (Non-HDD Type)
Software Update Procedure (Continued)
10. When finished, a “Software update complete”
message is displayed.
Figure 7.
.
11. Remove the USB Drive SST.
12. Turn the vehicle off then restart it.
13. Confirm the software version was updated
by performing the Software Version
Check Procedure.
Figure 8..
5
© 2015 Toyota Motor Sales, USA