JTB00600NAS2

3/2/2018
JTB00600NAS2 - Engine MIL Illuminated With DTC P013E-00 Stored | TOPIx
JTB00600NAS2
TECHNICAL BULLETIN
02 MAR 2018
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with
the knowledge, tools, and equipment required to do the job properly and safely. It informs these
Technicians of conditions that may occur on some vehicles, or provides information that could assist in
proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are not a
Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Jaguar
service facility to determine whether this bulletin applies to a specific vehicle.
INFORMATION
This reissue replaces all previous versions. Please destroy all previous versions.
Changes are highlighted in blue
SECTION:
303-14: Electronic Engine Controls
SUBJECT/CONCERN:
Engine MIL Illuminated With DTC P013E-00 Stored
AFFECTED VEHICLE RANGE:
MODEL:
F-PACE (X761)
MODEL YEAR:
2018
VIN:
898729-899997
https://topix.jaguar.jlrext.com/topix/content/document/view?id=885919
ASSEMBLY PLANT:
Solihull
APPLICABILITY:
INGENIUM I4 2.0L Petrol
1/5
3/2/2018
JTB00600NAS2 - Engine MIL Illuminated With DTC P013E-00 Stored | TOPIx
MODEL:
MODEL YEAR:
VIN:
ASSEMBLY PLANT:
APPLICABILITY:
F-PACE (X761)
2018
240000-283983
Solihull
INGENIUM I4 2.0L Petrol
XE (X760)
2018
P06869-P33274
Castle Bromwich
INGENIUM I4 2.0L Petrol
XF (X260)
2018
Y46487-Y64150
Castle Bromwich
INGENIUM I4 2.0L Petrol
MARKETS:
NORTH AMERICA
CONDITION SUMMARY:
SITUATION:
The engine Malfunction Indicator Lamp (MIL) may be illuminated on the Instrument Cluster (IC). Upon
diagnosis, a Technician may find Diagnostic Trouble Code (DTC) P013E-00 stored in the Powertrain
Control Module (PCM).
CAUSE:
This may be caused by the Heated Oxygen Sensor (HO2S) delay diagnostic running too soon following a
fuel cut/catalytic converter clear out event.
ACTION:
Should a customer express this concern, follow the Diagnostic Procedure below.
PARTS:
No Parts Required
TOOLS:
https://topix.jaguar.jlrext.com/topix/content/document/view?id=885919
2/5
3/2/2018
JTB00600NAS2 - Engine MIL Illuminated With DTC P013E-00 Stored | TOPIx


Jaguar Land Roverapproved
Midtronics battery
power supply
Jaguar Land Roverapproved
diagnostic tool with
latest PATHFINDER
software
WARRANTY:
NOTES:
Repair procedures are under constant review, and therefore times are subject to change; those
quoted here must be taken as guidance only. Always refer to JLR claims submission system to
obtain the latest repair time.
The JLR Claims Submission System requires the use of causal part numbers. Labor only claims
must show the causal part number with a quantity of zero.
DESCRIPTION
Configure existing PCM
SRO
86.99.26
TIME (HOURS)
0.2
CONDITION CODE
42
CAUSAL PART
T4N13811
NOTE:
Normal Warranty procedures apply.
DIAGNOSTIC PROCEDURE: PATHFINDER
This Diagnostic Procedure is only for vehicles requiring the Jaguar Land Rover-approved
diagnostic tool with PATHFINDER.
CAUTIONS:
https://topix.jaguar.jlrext.com/topix/content/document/view?id=885919
3/5
3/2/2018
JTB00600NAS2 - Engine MIL Illuminated With DTC P013E-00 Stored | TOPIx
A Jaguar Land Rover-approved Midtronics battery power supply must be connected to the
vehicle battery during diagnosis / module programming.
All ignition ON/OFF requests must be carried out. Failure to perform these steps may cause
damage to control modules in the vehicle.
NOTE:
Use DDW to check for Field Service Action program eligibility requiring a Powertrain Control
Module (PCM) software update. If eligible, perform and claim the update as per that program.
1
2
Connect the Jaguar Land Rover-approved Midtronics battery power supply to the vehicle battery.
NOTE:
The Jaguar Land Rover-approved diagnostic tool must be loaded with PATHFINDER
version 144 (or later).
Connect the Jaguar Land Rover-approved diagnostic tool to the vehicle and begin a new session.
3
NOTE:
The Jaguar Land Rover-approved diagnostic tool will read the correct Vehicle Identification
Number (VIN) for the current vehicle and automatically take the vehicle out of Transit mode
if required.
Follow all on-screen instructions.
4
Select ECU Diagnostics.
5
Select Powertrain control module [PCM].
6
Select Update ECU.
1 Follow all on-screen instructions until the application completes successfully.
2 When all tasks are complete, go to the next Step.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=885919
4/5
3/2/2018
7
JTB00600NAS2 - Engine MIL Illuminated With DTC P013E-00 Stored | TOPIx
Exit the current session.
1 If required, reset the vehicle to Transit mode.
2 Select the Exit icon.
8
Disconnect the diagnostic tool and battery power supply from the vehicle.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=885919
5/5