TSB18-2088

Service Bulletin Details

Public Details for: TSB18-2088

Some 2014-2018 taurus vehicles may exhibit the gearshift selector lever bezel door binding, skewed and/or not latching. This may be due to the door post becoming detached from the trim panel door pivot linkage. Follow the service procedure


- 2018 - 2017 - 2016 - 2015 - 2014 -

Models from 2018
2018 FORD TAURUS
Models from 2017
2017 FORD TAURUS
Models from 2016
2016 FORD TAURUS
Models from 2015
2015 FORD TAURUS
Models from 2014
2014 FORD TAURUS
18-2088
TECHNICAL SERVICE BULLETIN
15 March
Gearshift Selector Lever Bezel Door Binding, Skewed And/Or Not Latching
2018
Model:
Ford
2014-2018 Police Interceptor Sedan
2014-2018 Taurus
Issue: Some 2014-2018 Taurus and Police Interceptor Sedan vehicles may exhibit the gearshift selector lever bezel
door binding, skewed and/or not latching. This may be due to the door post becoming detached from the bezel door
pivot linkage.
Action: Follow the Service Procedure steps to correct the condition.
Parts
Part
Number
54045A76
Description
Quantity
Gearshift Selector Lever Bezel – Refer To The Parts Catalogue For The VIN Specific
Application
1
Warranty Status: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage Warranty/ESP coverage
limits/policies/prior approvals are not altered by a TSB. Warranty/ESP coverage limits are determined by the
identified causal part and verified using the OASIS part coverage tool.
Labor Times
Operation
Time
No.
Description
2014-2018 Taurus and Police Interceptor Sedan: Inspect And Repair Or Replace Selector Lever
Bezel (Do Not Use With Any Other Labor Operations)
182088A
Repair/Claim Coding
Causal Part:
54045A76
Condition Code: 42
Drive
Tool Name
1/4"
Power Tool
1/4"
Ratchet
1/4"
6" Extension
1/4"
7 mm Socket
Trim Tool
Service Procedure
1. Inspect the door pivot pin and pivot pin linkage for damage. Is any damage present? (Figures 1 - 2)
(1). Yes - replace the gearshift selector lever bezel. Refer to Workshop Manual (WSM), Section 307-05.
(2). No - proceed to step 2.
Figure 1
0.4
Hrs.
Figure 2
2. Gently pull up on the edge of the door and align with the linkage, then snap the pivot post into the pivot linkage
and cycle the lid to verify proper operation. Does the door function properly? (Figure 3)
(1). Yes - repair is complete.
(2). No - replace the gearshift selector lever bezel. Refer to WSM, Section 307-05.
Figure 3
© 2018 Ford Motor Company
All rights reserved.
NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, and
equipment to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides information
that could assist in proper vehicle service. The procedures should not be performed by "do-it-yourselfers". Do not assume that a condition
described affects your car or truck. Contact a Ford or Lincoln dealership to determine whether the Bulletin applies to your vehicle. Warranty Policy
and Extended Service Plan documentation determine Warranty and/or Extended Service Plan coverage unless stated otherwise in the TSB article.
The information in this Technical Service Bulletin (TSB) was current at the time of printing. Ford Motor Company reserves the right to supersede
this information with updates. The most recent information is available through Ford Motor Company's on-line technical resources.


© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.