ITB16-046a
Service Bulletin Details
Public Details for: ITB16-046a
Revised wheel alignment specifications this bulletin has been amended. The applied vehicles were updated with new models and model years. No other changes have been made. Discard previous versions of this bulletin.
Models from 2018
2018 INFINITI Q50 |
2018 INFINITI Q60 |
2018 INFINITI Q70 |
2018 INFINITI Q70 HYBRID |
2018 INFINITI QX30 |
Models from 2017
2017 INFINITI Q50 |
2017 INFINITI Q50 HYBRID |
2017 INFINITI Q60 |
2017 INFINITI Q70 |
2017 INFINITI Q70 HYBRID |
2017 INFINITI QX30 |
2017 INFINITI QX50 |
2017 INFINITI QX80 |
Models from 2016
2016 INFINITI Q50 |
2016 INFINITI Q50 HYBRID |
2016 INFINITI Q70 |
2016 INFINITI Q70 HYBRID |
2016 INFINITI QX50 |
2016 INFINITI QX80 |
Classification: Reference: Date: FA16-003a ITB16-046a April 20, 2018 REVISED WHEEL ALIGNMENT SPECIFICATIONS This bulletin has been amended. The APPLIED VEHICLES were updated with new models and model years. No other changes have been made. Discard previous versions of this bulletin. APPLIED VEHICLES: 2017 – 2018 QX30 (H15) 2017 – 2018 Q60 (V37) 2016 – 2018 Q50 (V37) 2016 – 2018 Q50 Hybrid (V37) 2016 – 2018 Q70 (Y51) 2016 – 2018 Q70 Hybrid (Y51) 2016 – 2017 QX50 (J50) 2016 – 2017 QX80 (Z62) SERVICE INFORMATION For the Applied Vehicles listed above, some front and rear wheel alignment specifications listed in the Electronic Service Manual (ESM), sections - Front Suspension and Rear Suspension, were listed incorrectly. Updated ESMs will be distributed to the field as quickly as possible. Until the updated ESMs are made available, please use the corrected specifications listed in this bulletin. Specification areas that have corrections are outlined with a Red box on the following pages. Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti retailer to determine if this applies to your vehicle. 1/25 Table of Contents Page 2017 – 2018 QX30 (2WD, 2.0L Turbo)……………………………………………………………………… 2017 – 2018 QX30 (AWD, 2.0L Turbo)……………………………………………………………………... 2017 – 2018 QX30 (2WD, 2.0L Turbo) Rear, Except Canada…………………………………………… 2017 – 2018 QX30 (2WD, 2.0L Turbo) Rear, Canada…………………………………..………………… 2017 – 2018 QX30 (AWD, 2.0L Turbo) Rear, Except Canada………...……………………………….… 2017 – 2018 QX30 (AWD, 2.0L Turbo) Rear, Canada……………………………………………….…… 3 4 5 5 6 6 2017 – 2018 Q60 (2WD, Except VR30DDTT) …………………………………………………...……..…. 2017 – 2018 Q60 (2WD, VR30DDTT) ………………………………………………………….…...……… 2017 – 2018 Q60 (AWD, 2.0L Turbo Gasoline Engine, Except Canada) ……………………….……… 2017 – 2018 Q60 (AWD, VR30DDTT) …………………………………………………………………..…. 2016 – 2018 Q50 (2WD, VR30DDTT; Except for Premium Sport Grade) ……………………………... 2016 – 2017 Q50 (2WD, VR30DDTT; For Premium Sport Grade) ……………….…………………….. 2016 – 2018 Q50 (2WD, Except VR30DDTT)……………………………………………………………… 2017 – 2018 Q50 (AWD, Except VR30DDTT)……………………………………………………...……… 2017 – 2018 Q50 (AWD, VR30DDTT)………………………………………………………………….…… 2016 – 2018 Q50 Hybrid (2WD) …………………………………………………………………..………… 2016 – 2018 Q50 Hybrid (AWD)…………………………………………………………………………….. 2016 – 2018 Q70 Hybrid …………………………………………………………………………………….. 2016 – 2017 Q70 (2WD) …………………………………………………………………………………….. 2016 – 2017 Q70 (AWD) ……………………………………………………………………………….……. 2018 Q70 (2WD) ……………………………………………………………………………………………… 2018 Q70 (AWD) ……………………………………………………………………………………………… 2016 – 2017 QX50 (AWD) …………………………………………………………………………………… 2017 QX50 (2WD) ……………………………………………………………………………………………. 2016 – 2017 QX80 ……………………………………………………………………………………………. 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 2/25 ITB16-046a 2017 – 2018 QX30 2WD 2.0L Turbo Front Wheel Alignment Specifications Total toe‐in Distance Toe‐in Total toe angle Degree minute (Decimal Degree) Minimum 0.2mm 0.2mm Nominal 2.7mm 2.7mm Maximum 5.2mm Minimum In 0°01'12"(In 0.02°) Nominal In 0°13'48"(In 0.23°) Maximum In 0°26'24"(In 0.44°) 5.2mm In 0°01'12"(In 0.02°) In 0°13'48"(In 0.23°) In 0°26'24"(In 0.44°) Measure value under unladen*2 conditions. *1: A difference when assuming the left side a standard. *2: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 3/25 ITB16-046a 2017 – 2018 QX30 AWD 2.0L Turbo Front Wheel Alignment Specifications Total toe‐in Distance Toe‐in Total toe angle Degree minute (Decimal Degree) Minimum 0.2mm Nominal 2.7mm Maximum 5.2mm Minimum In 0°01'12"(In 0.02°) Nominal In 0°13'48"(In 0.23°) Maximum In 0°26'24"(In 0.44°) Measure value under unladen*2 conditions. *1: A difference when assuming the left side a standard. *2: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 4/25 ITB16-046a 2017 – 2018 QX30 Rear Wheel Alignment Specifications 2WD 2.0L Turbo Engine - EXCEPT Canada Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 2WD 2.0L Turbo Engine - Canada Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 5/25 ITB16-046a 2017 – 2018 QX30 Rear Wheel Alignment Specifications AWD 2.0L Turbo Engine - EXCEPT Canada AWD 2.0L Turbo Engine - Canada Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 6/25 ITB16-046a 2017 - 2018 Q60 2WD Except VR30DDTT Front Wheel Alignment Specifications Total toe‐in Distance Toe‐in Total toe angle Degree minute (Decimal Degree) Minimum ‐0.5mm Nominal 2.0mm Maximum 4.5mm Minimum Out 0°03'(Out 0.04°) Nominal In 0°10'(In 0.17°) Maximum In 0°23'(In 0.38°) 7/25 ITB16-046a 2017 - 2018 Q60 2WD VR30DDTT Front Wheel Alignment Specifications Total toe‐in Distance Toe‐ in Total toe angle Degree minute (Decimal Degree) Minimum Nominal ‐0.5mm 2.0mm Maximum 4.5mm Minimum Out 0°03'(Out 0.04°) Nominal In 0°10'(In 0.17°) Maximum In 0°23'(In 0.38°) Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 8/25 ITB16-046a 2017 – 2018 Q60 AWD 2.0L Turbo Front Wheel Alignment Specifications Total toe‐in Distance Toe‐in Total toe angle Degree minute (Decimal Degree) Minimum ‐0.5mm Nominal 2.0mm Maximum 4.5mm Minimum Out 0°03'(Out 0.04°) Nominal In 0°10'(In 0.17°) Maximum In 0°23'(In 0.38°) Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 9/25 ITB16-046a 2017 – 2018 Q60 VR30DDTT Front Wheel Alignment Specifications Total toe‐in Distance Toe‐in Total toe angle Degree minute (Decimal Degree) Minimum ‐0.5mm Nominal 2.0mm Maximum 4.5mm Minimum Out 0°03'(Out 0.04°) Nominal In 0°10'(In 0.17°) Maximum In 0°23'(In 0.38°) Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 10/25 ITB16-046a 2016 – 2018 Q50 2WD VR30DDTT Front Wheel Alignment Specifications EXCEPT FOR PREMIUM SPORT GRADE Total toe‐in Distance Toe‐in Total toe angle Degree minute (Decimal Degree) Minimum ‐0.5mm Nominal 2.0mm Maximum 4.5mm Minimum Out 0°03'(Out 0.04°) Nominal In 0°10'(In 0.17°) Maximum In 0°23'(In 0.38°) Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 11/25 ITB16-046a 2016 – 2018 Q50 2WD VR30DDTT Front Wheel Alignment Specifications Total toe‐in Distance Toe‐in Total toe angle Degree minute (Decimal Degree) Minimum ‐0.5mm Nominal 2.0mm Maximum 4.5mm Minimum Out 0°03'(Out 0.04°) Nominal In 0°10'(In 0.17°) Maximum In 0°23'(In 0.38°) Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 12/25 ITB16-046a 2017 – 2018 Q50 2WD (EXCEPT VR30DDTT) Front Wheel Alignment Specifications Total toe‐in Distance Toe‐in Total toe angle Degree minute (Decimal Degree) Minimum ‐0.5mm Nominal 2.0mm Maximum 4.5mm Minimum Out 0°03'(Out 0.04°) Nominal In 0°10'(In 0.17°) Maximum In 0°23'(In 0.38°) Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 13/25 ITB16-046a 2017 – 2018 Q50 AWD 2.0L Turbo Front Wheel Alignment Specifications Item Minimum Standard –1° 20′ (–1.33°) Camber Nominal –0° 35′ (–0.58°) Degree minute (Decimal degree) Maximum Left and right difference 0° 10′ (0.16°) 0° 30′ (0.50°) or less Minimum 3° 00′ (3.00°) Caster Nominal 4° 20′ (4.33°) Degree minute (Decimal degree) Maximum 5° 40′ (5.66°) Left and right difference 0° 30′ (0.50°) or less Minimum 6° 45′ (6.75°) Nominal 7° 30′ (7.50°) Maximum 8° 15′ (8.25°) Kingpin inclination Degree minute (Decimal degree) Total toe‐in Distance Toe‐in Total toe angle Degree minute (Decimal Degree) Minimum ‐0.5mm Nominal 2.0mm Maximum 4.5mm Minimum Out 0°03'(Out 0.04°) Nominal In 0°10'(In 0.17°) Maximum In 0°23'(In 0.38°) Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 14/25 ITB16-046a 2017 – 2018 Q50 AWD VR30DDTT Front Wheel Alignment Specifications Item Minimum Standard –1° 20′ (–1.33°) Camber Nominal –0° 35′ (–0.58°) Degree minute (Decimal degree) Maximum Left and right difference Minimum 0° 10′ (0.16°) 0° 30′ (0.50°) or less 2° 55′ (2.92°) Caster Nominal 4° 15′ (4.25°) Degree minute (Decimal degree) Maximum Left and right difference Minimum 5° 35′ (5.58°) Kingpin inclination Degree minute (Decimal degree) Total toe‐in Distance Toe‐in Total toe angle Degree minute (Decimal Degree) 0° 30′ (0.50°) or less 6° 45′ (6.75°) Nominal 7° 30′ (7.50°) Maximum 8° 15′ (8.25°) Minimum ‐0.5mm Nominal 2.0mm Maximum 4.5mm Minimum Out 0°03'(Out 0.04°) Nominal In 0°10'(In 0.17°) Maximum In 0°23'(In 0.38°) Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 15/25 ITB16-046a 2016 – 2018 Q50 Hybrid 2WD Front Wheel Alignment Specifications Total toe‐in Distance Toe‐in Total toe angle Degree minute (Decimal Degree) Minimum ‐0.5mm Nominal 2.0mm Maximum 4.5mm Minimum Out 0°03'(Out 0.04°) Nominal In 0°10'(In 0.17°) Maximum In 0°23'(In 0.38°) Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 16/25 ITB16-046a 2016 – 2018 Q50 Hybrid AWD Front Wheel Alignment Specifications Total toe‐in Distance Toe‐in Minimum ‐0.5mm Nominal 2.0mm Maximum 4.5mm Total toe angle Degree minute Minimum (Decimal Degree) Nominal Out 0°03'(Out 0.04°) In 0°10'(In 0.17°) Maximum In 0°23'(In 0.38°) Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 17/25 ITB16-046a 2016 - 2018 Q70 Hybrid Front Wheel Alignment Specifications Total toe‐in Distance Toe‐in Total toe angle Degree minute (Decimal Degree) Minimum ‐1.0mm Nominal 1.5mm Maximum 4.0mm Minimum Out 0°05'(Out 0.08°) Nominal In 0°08'(In 0.13°) Maximum In 0°20'(In 0.33°) Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 18/25 ITB16-046a 2016 - 2017 Q70 Front Wheel Alignment Specifications 2WD Total toe‐in Distance Toe‐in Total toe angle Degree minute (Decimal Degree) Minimum ‐1.0mm Nominal 1.5mm Maximum 4.0mm Minimum Out 0°05'(Out 0.08°) Nominal In 0°08'(In 0.13°) Maximum In 0°20'(In 0.33°) Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 19/25 ITB16-046a 2016 - 2017 Q70 Front Wheel Alignment Specifications AWD Total toe‐in Distance Minimum ‐1.0mm Nominal 1.5mm Maximum 4.0mm Minimum Out 0°05'(Out 0.08°) Nominal In 0°08'(In 0.13°) Maximum In 0°20'(In 0.33°) Toe‐in Total toe angle Degree minute (Decimal Degree) Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 20/25 ITB16-046a 2018 Q70 Front Wheel Alignment Specifications 2WD Total toe‐in Distance Toe‐in Total toe angle Degree minute (Decimal Degree) Minimum ‐1.0mm Nominal 1.5mm Maximum 4.0mm Minimum Out 0°05'(Out 0.08°) Nominal In 0°07'(In 0.12°) Maximum In 0°20'(In 0.33°) Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 21/25 ITB16-046a 2018 Q70 Front Wheel Alignment Specifications AWD Total toe‐in Distance Toe‐in Total toe angle Degree minute (Decimal Degree) Minimum ‐1.0mm Nominal 1.5mm Maximum 4.0mm Minimum Out 0°05'(Out 0.08°) Nominal In 0°07'(In 0.12°) Maximum In 0°20'(In 0.33°) Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 22/25 ITB16-046a 2016 - 2017 QX50 Front Wheel Alignment Specifications AWD Total toe‐in Distance Toe‐in Total toe angle Degree minute (Decimal Degree) Minimum ‐1.5mm Nominal 1.0mm Maximum 3.5mm Minimum Out 0°07'30"(Out 0.12°) Nominal In 0°04'48"(In 0.08°) Maximum In 0°17'00"(In 0.28°) Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 23/25 ITB16-046a 2017 QX50 Front Wheel Alignment Specifications 2WD Total toe‐in Distance Minimum ‐1.5mm Nominal 1.0mm Maximum 3.5mm Minimum Out 0°07'30"(Out 0.12°) Nominal In 0°04'48"(In 0.08°) Maximum In 0°17'00"(In 0.28°) Toe‐in Total toe angle Degree minute (Decimal Degree) Measure value under unladen* conditions. *: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. 24/25 ITB16-046a 2016 - 2017 QX80 Front Wheel Alignment Specifications 25/25 ITB16-046a