B14-031

Service Bulletin
July 3, 2018
14-031
Version 1
Steering Column Screeches When Moving
Supersedes 14-031, dated June 1, 2017, to revise the information highlighted in yellow
AFFECTED VEHICLES
Year
Model
Trim
VIN Range
2014-16
RLX
ALL
ALL
2014,
2016
RLX Hybrid
ALL
ALL
REVISION SUMMARY
MDX was removed from this bulletin. Refer to service bulletin 18-033, Steering Column Screeches When Moving.
SYMPTOM
In high ambient temperatures, the steering column screeches or squeals when it moves in or out.
POSSIBLE CAUSES
Premature wear of the steering column gearbox components.
CORRECTIVE ACTION
Replace the steering column assembly.
PARTS INFORMATION
Part Name
Part Number
Quantity
Steering Column
53200-TY2-A03
1
Driver’s Knee Airbag Bolts
90178-SNA-003
4
Steering Lock Kit (bracket and two left-hand thread bolts)
06352-TX4-A11
1
Steering Wheel Bolt
90161-TX4-000
1
Driver’s Airbag Bolts
90134-S6A-A80
2
CLIENT INFORMATION:The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and
training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume
this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an
authorized Acura automobile dealer.
©
2018 American Honda Motor Co., Inc. — All Rights Reserved
Page 1 of 9
WARRANTY CLAIM INFORMATION
The normal warranty applies.
Operation
Number
Description
Flat Rate
Time
Defect
Code
Symptom
Code
Template
ID
Failed Part Number
510100
Remove and replace
the steering column
1.1 hrs
07409
04201
14-031N
53200-TY2-A02
D
Add for alignment
0.4 hr
07409
04201
14-031P
53200-TY2-A02
Skill Level: Repair Technician
REPAIR PROCEDURE
1. Do the battery terminal disconnection procedure.
2. Remove the driver’s airbag.
3. Remove the steering wheel.
4. Remove the driver’s dashboard lower cover.
5. Remove the steering column cover.
6. Disconnect the combination switch connectors and remove the clip.
Page 2 of 9
7. Remove the clips and disconnect the following connectors:
•
Cable reel connectors
•
Steering angle sensor connector
•
(2014–15 models only): Electric steering lock connector
•
Tilt/telescopic motors connector
8. Remove the combination switch body assembly from the steering column shaft.
9. Disconnect the driver’s knee airbag inflator connector, then remove the mounting bolts.
Page 3 of 9
10. Remove the steering joint cover.
11. Hold the lower side shaft on the column with a piece of wire between the joint yoke of the lower side shaft and the
joint yoke of the upper shaft to prevent the lower slide shaft from pulling out.
Page 4 of 9
12. Remove the steering joint bolt, then disconnect the steering joint from the pinion shaft.
NOTE
If the center guide is in place and has not moved, leave it in place. If the center guide has come off, discard it.
13. Remove the steering column.
14. 2014–15 RLX, 2014 RLX Hybrid: Centerpunch both of the two shear bolts and drill out the heads with a 5 mm (0.20
in) drill bit.
NOTE
The shear bolts have left-hand threads.
Page 5 of 9
15. Install the steering lock onto the new steering column with the new bracket and new left- hand thread bolts.
16. Install the steering column.
NOTE
Make sure the connectors are securely connected and the wires are not caught or pinched by any parts.
17. Remove the wire.
Page 6 of 9
18. Set the rack in the straight-ahead position and slip the steering joint onto the pinion shaft.
NOTE
If the pinion shaft has a guide, install the steering joint so the gap aligns with the center guide. If the pinion shaft
does not have a guide, position the steering column by aligning the gap within the angle.
19. Align the bolt hole on the steering joint with the groove around the pinion shaft and loosely install the steering joint
bolt. Be sure the joint bolt is securely in the groove. Pull on the steering joint to make sure the bolt is fully seated,
then tighten it to 29 N·m (21 lb-ft).
20. Install the steering joint cover.
Page 7 of 9
21. Install the driver’s knee airbag and torque the new mounting bolts to 9.4 N·m (6.9 lb-ft). Then, connect the driver’s
knee airbag inflator connector.
22. Install the combination switch body assembly and tighten the three screws in the numbered sequence as shown.
23. Install the clips and connect the following connectors:
•
Tilt/telescopic motors connector
•
Cable reel connector A
•
Cable reel connector B
•
Steering angle sensor connector
•
(2014–15 models only): Electric steering lock connector
Page 8 of 9
24. Install the clip and connect the combination switch connectors.
25. Install the column cover.
26. Install the driver’s dashboard lower cover.
27. Install the steering wheel and tighten the new steering wheel bolt.
NOTES
The steering wheel bolt is coated with either a green or blue thread lock. The specified torque value varies
depending on the type of steering wheel bolt used.
•
Green-Coated Bolts: 49 N·m(36 lb-ft)
•
Blue-Coated Bolts: 60 N·m (44 lb-ft)
28. Install the driver’s airbag and torque the new Torx bolts to 9.4 N·m (6.9 lb-ft).
29. Do the battery terminal connection procedure.
30. Check the wheel alignment and adjust it if necessary.
31. Do the VSA sensor neutral position memorization procedure.
32. Do the driving position memory clear procedure.
NOTE
If the driving position memory is not cleared, the column will not have its full range of travel.
END
Page 9 of 9