122-S6R3L-08
Service Bulletin Details
Public Details for: 122-S6R3L-08
Cause if the hall sensor is not positioned correctly or if it becomes slightly detached, there will be too much of a gap between the sensor and component and an error message will be displayed.
Models from 2015
2015 PORSCHE 911 |
Models from 2014
2014 PORSCHE 911 |
Service Technical Information 11/16 ENU 6847 6 Symptom in Vehicle Interior - Wind Deflector/Convertible Top Does Not Close: Reworking Hall Sensor (SY 11/16) General information Symptom Customers complain that the convertible top or wind deflector cannot be closed. Cause, introduction date and remedial action Cause If the Hall sensor is not positioned correctly or if it becomes slightly detached, there will be too much of a gap between the sensor and component and an error message will be displayed. Model Year: As of 2014 up to 2015 - 911 (991) Remedial action Installation position of Hall sensor for wind deflector A defined gap between the Hall sensor and component must be observed. The Hall sensor is bonded at the defined position and is also held in position with a fixing clip. AfterSales Jul 24, 2018 Page 1 of 4 6 Service 6847 ENU Technical Information 11/16 Tools and materials Tools and materials • • • • Cleaning cloth Isopropanol (commercially available) Adhesive ADHESIVE 999.915.650.40 Fixing clip SPRING CLAMP 991.561.936.00 Securing Hall sensor for wind deflector Securing Hall sensor for wind deflector WARNING Toxic substances • Danger of poisoning or suffocation Ventilate the work area well. Never ingest or inhale. Read specific information on the MSDS Sheet. Wear personal protective gear. 1 Remove trim panel for rear wall. Workshop Manual '703119 Removing and installing trim panel for rear wall - section on "Removing"' 2 Remove rear side trim panel at the left. Workshop Manual '707519 Removing and installing rear side trim panel - section on "Removing"' 3 Loosen fixing clip Removing fixing clip -1- and remove Hall sensor Removing fixing clip -2-. 4 Slightly roughen the areas marked in blue. Removing fixing clip Jul 24, 2018 Page 2 of 4 AfterSales Service Technical Information 11/16 ENU 6847 6 Roughen the surface of the Hall sensor facing the body. 5 Clean areas marked in blue with isopropanol. Preparing bonding surfaces Clean the surface of the Hall sensor facing the body. 6 Apply adhesive ADHESIVE 999.915.323.40 to the areas marked in blue. Preparing bonding surfaces Apply adhesive to the side of the Hall sensor facing the body. 7 Fit Hall sensor. Apply adhesive AfterSales Jul 24, 2018 Page 3 of 4 6 Service 6847 ENU 8 Technical Information 11/16 Fit fixing clip Fitting fixing clip -1- and press Hall sensor on using a screwdriver. Fitting fixing clip Invoicing Invoicing The work involved is invoiced under the labor operation: APOS Labor operation 68474900 Reworking wind deflector I No. For invoicing and documentation using PQIS, enter the following coding: Location (FES5) 68470 Wind deflector Damage type (SA4) 1613 Does not work at times Important Notice: Technical Bulletins issued by Porsche Cars North America, Inc. are intended only for use by professional automotive technicians who have attended Porsche service training courses. They are written to inform those technicians of conditions that may occur on some Porsche vehicles, or to provide information that could assist in the proper servicing of a vehicle. Porsche special tools may be necessary in order to perform certain operations identified in these bulletins. Use of tools and procedures other than those Porsche recommends in these bulletins may be detrimental to the safe operation of your vehicle, and may endanger the people working on it. Properly trained Porsche technicians have the equipment, tools, safety instructions, and know-how to do the job properly and safely. Part numbers listed in these bulletins are for reference only. The work procedures updated electronically in the Porsche PIWIS diagnostic and testing device take precedence and, in the event of a discrepancy, the work procedures in the PIWIS Tester are the ones that must be followed. © 2018 Porsche Cars North America, Inc. Jul 24, 2018 Page 4 of 4 AfterSales