Technician Refer

2019
Pre-Delivery Inspection
Technician Reference Document
Effective 9-17-2018-US
Version 1.0
Table of Contents
Technician Reference Document
Technician Reference Document Overview
The Pre-Delivery Inspection Technician Reference Document is designed to be a resource used in hand with
the Pre-Delivery Inspection Checklist (PDI). The PDI Checklist has been simplified to make the process more
efficient, and in doing so, this document has been created to be used as a reference for checklist items that
may have additional information. On the PDI Checklist, you find that certain items have been notated with an
asterisk symbol (*), this lets you know that additional information can be found in this Technician Reference
Document.
Below you will find a list of each model, with the page numbers to their left. After navigating to the desired
page, you will notice each model page is formatted similarly to the PDI Checklists. After each section title is the
original checklist item, followed by any additional information specific to that model.
Table of Contents
3-4
A3 Sedan & Cabriolet/S3/RS 3
5-6
A4/S4/A4 allroad
7-8
A5/S5/RS 5
9-10
A6
11-12
A7
13-14
A8 L
15-16
Q5/SQ5
17-18
Q7
19-20
Q8
21-22
TT/TTS/TTRS
Effective 9-17-2018-US
Version 1.0
Model Year 2019 | Audi Pre-Delivery Reference Document | 2
A3 Sedan & Cabriolet/S3/RS 3
Technician Reference Document
Vehicle Preparation
Interior (continued)
•      Deactivate vehicle transport mode
•      Check rear view mirror operation
This step must be performed with the ignition on/engine
off or the 03 brake module may remain in transport mode.
See TSB 2042954 for resolution.
Deactivate vehicle transport mode (via Special functions >
PDI service > 19-Transport mode activating/deactivating.)
•      Set service reminder
via Special functions > PDI service > 17-PDI-resetting SRI at
PDI, counter reset, etc.
•      Perform any open campaigns
Follow instructions listed in campaign documentation
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
Lighting and Windshield
•      Test front washers (and headlight washers on S3 and RS 3)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Verify temporary inflatable spare tire is present (A3 Sedan,
S3, and A3 Cabriolet FWD only)
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Check battery clamps for proper torque
Check self-dimming function/lighting
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation (Sedan
only)
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set time source setting to “GPS” and set auto daylight
savings time to “on.”*
Change time zone appropriate to dealer location
•      Verify and set language and measurement units
This can be changed in the Settings menu by going to Menu >
Vehicle > Vehicle settings
•      Verify Speech Dialog System is operating (if equipped)
Press the “Talk” button and verify several commands
•      Set “Entertain. Fad.” in Parking aid to an audible level (if
equipped)
Via “Menu > Vehicle > Left Option > Driver Assistance >
Parking Aid”
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning
This can be changed in the Driver Assistance Settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual > Select OffMedia / Radio / SAT
Refer to Elsa Pro for specification
Media / Radio / SAT
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
Effective 9-17-2018-US
Version 1.0
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect® (USA ONLY) (if equipped)
•      Turn on the Wi-Fi® hotspot (if equipped)
Ensure the wireless network is turned on (Telephone > Right
Option > Wi-Fi® options > Wi-Fi® “On”)
Model Year 2019 | Audi Pre-Delivery Reference Document | 3
A3 Sedan & Cabriolet/S3/RS 3
Technician Reference Document
Audi connect® (USA ONLY) (if equipped) (continued)
Cabriolet Functionality
•      Check Wi-Fi® hotspot visibility. No data available at PDI (if
equipped)
•      Test operation of power folding top
Check Wi-Fi® hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Enable Google Earth view for navigation (if equipped)
Enable Google Earth view in the Navigation > Map Settings
and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol.
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
Perform with engine running to conserve battery power
Post-Road Test Inspection
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis > Special functions > PDI Service. Select
option 2, the battery test for new batteries as part of the
Pre-Delivery Inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless server)
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Driving Performance
•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
•      Verify operation of Audi parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Effective 9-17-2018-US
Version 1.0
Model Year 2019 | Audi Pre-Delivery Reference Document | 4
A4/S4/A4 allroad
Technician Reference Document
Vehicle Preparation
Interior (continued)
•      Deactivate vehicle transport mode
•      Inspect mirrors for proper operation
This step must be performed with the ignition on/engine
off or the 03 brake module may remain in transport mode.
See TSB 2042954 for resolution.
Note: The VAS 6154 diagnostic head is required along with
ODIS Audi Brand version 2.15.5 or higher. Reference TSB
2052299 for more information.
Deactivate vehicle transport mode (via Special functions >
PDI service > 19-Transport mode activating/deactivating.)
•      Set service reminder
via Special functions –> PDI service –> 17-PDI-resetting SRI
at PDI, counter reset, etc
•      Perform any open campaigns
Follow instructions listed in campaign documentation
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
Lighting and Windshield
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Set spare tire pressure
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      
Effective 9-17-2018-US
Version 1.0
Inspect folding, adjustments, right side tilt in reverse, heating
•      Check rear view mirror operation
Check self-dimming function/lighting
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Settings menu by going to Menu >
Vehicle > Vehicle settings
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands
•      Set “Entertain. Fad.” in Parking aid to an audible level
Via “Menu > Vehicle > Left Option > Driver Assistance > Parking Aid”
•      Set “Music volume while parking” to medium
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning (if equipped)
This can be changed in the Driver Assistance settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual > Select Off
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Model Year 2019 | Audi Pre-Delivery Reference Document | 5
A4/S4/A4 allroad
Technician Reference Document
Audi connect® (USA ONLY) (if equipped)
Driver Assistance (continued)
•      Turn on the Wi-Fi® hotspot (if equipped)
•      Verify all vehicle Head-up display functionality (if
equipped)
Ensure the wireless network is turned on (Telephone > Right
Option > Wi-Fi® options > Wi-Fi® “On”)
•      Check Wi-Fi® hotspot visibility. No data available at PDI (if
equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Enable Google Earth view for navigation (if equipped)
Enable Google Earth view in the Navigation > Map Settings
and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol.
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-up display (as
equipped)
Post-Road Test Inspection
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> PDI service. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Driving Performance
•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
•      Verify operation of parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Effective 9-17-2018-US
Version 1.0
Model Year 2019 | Audi Pre-Delivery Reference Document | 6
A5/S5/RS 5
Technician Reference Document
Vehicle Preparation
Interior (continued)
•      Deactivate vehicle transport mode
•      Inspect mirrors for proper operation
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)Check rear view mirror operation
This step must be performed with the ignition on/engine
off or the 03 brake module may remain in transport mode.
See TSB 2042954 for resolution.
Check self-dimming function/lighting (if equipped)
Note: The VAS 6154 diagnostic head is required along with
ODIS Audi Brand version 2.15.5 or higher. Reference TSB
2052299 for more information.
•      Set service reminder
via Special functions –> PDI service –> 17-PDI-resetting SRI
at PDI, counter reset, etc.
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
Lighting and Windshield
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Set spare tire pressure
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
Interior
•      Check operation of window, lock, and seat controls
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Setup/Settings menu
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands
•      Set “Entertain. Fad.” in Parking aid to an audible level
Via Menu > Vehicle > Driver Assistance > Parking Aid
•      Set “Music volume while parking” to medium
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning (if equipped)
This can be changed in the Driver Assistance settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual->Select Off
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
Effective 9-17-2018-US
Version 1.0
Model Year 2019 | Audi Pre-Delivery Reference Document | 7
A5/S5/RS 5
Technician Reference Document
Audi connect® (USA ONLY) (if equipped)
Driver Assistance
•      Turn on the Wi-Fi® hotspot (if equipped)
•      Verify operation of parking system (if equipped)
Ensure the wireless network is turned on (Telephone > Right
Option > Wi-Fi® options > Wi-Fi® “On”)
•      Check Wi-Fi® hotspot visibility. No data available at PDI (if
equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Enable Google Earth view for navigation (if equipped)
Enable Google Earth view in the Navigation > Map Settings
and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol.
On-Hoist Inspection
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
•      Verify all vehicle Head-up display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
Convertible Functionality (if equipped)
•      Test operation of power folding top
Perform with engine running to conserve battery power
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Driving Performance
•      Verify engine Start-Stop System functionality
Post-Road Test Inspection
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> PDI Service. Select option 2, the battery
test for new batteries as part of the pre–delivery inspection
and act according to the test result (ok, recharge, replace).
Ensure diagnosis log is uploaded to the GFF paperless server
by selecting “ok” when tester wants to send the current
generated diagnosis protocol online. (Note: Do not use Guided Function. The diagnosis log will not be uploaded to GFF
paperless)
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Effective 9-17-2018-US
Version 1.0
Model Year 2019 | Audi Pre-Delivery Reference Document | 8
A6
Technician Reference Document
Vehicle Preparation
Interior
•      Deactivate vehicle transport mode
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features
This step must be performed with the ignition on/engine
off or the 03 brake module may remain in transport mode.
See TSB 2042954 for resolution.
Note: The VAS 6154 diagnostic head is required along with
ODIS Audi Brand version 2.15.5 or higher. Reference TSB
2052299 for more information.
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
•      Deactivate air suspension loading mode (if equipped)
via Special Functions -> Service Work -> 34-Loading mode
activating/deactivating Warning! Car body may lower!
•      Set service reminder
via Special functions –> PDI Service –> 17-PDI-resetting SRI
at PDI, counter reset, etc.
•      Perform any open campaigns
Follow instructions listed in campaign documentation
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
Lighting and Windshield
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Set spare tire pressure
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
Effective 9-17-2018-US
Version 1.0
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Verify operation of heated/ventilated and massaging seats
(if equipped)
Check both front and rear. Massaging feature is in the front
seats only (if equipped)
•      Verify proper operation of climate control*
Ensure proper heating and A/C cooling, open all panel vents
for all zones
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on”
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Setup/Settings menu
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands
•      Set “Music volume while parking” to medium
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning (if equipped)
This can be changed in the Driver Assistance Settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual > Select Off
Model Year 2019 | Audi Pre-Delivery Reference Document | 9
A6
Technician Reference Document
Media / Radio / SAT
Driving Performance (continued)
•      Verify HD Radio is turned “off”
•      Calibrate rear view mirror
This can be found in the Radio/Settings Menu
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Audi connect® (USA ONLY) (if equipped)
•      Turn on the Wi-Fi® hotspot (if equipped)
Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” )
•      Check Wi-Fi® hotspot visibility. No data available at PDI
due to dealer demo mode (if equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX
is the last four digits of the VIN. Via Telephone > Options >
Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings
> Access point (SSID)
Driver Assistance
•      Verify operation of parking system
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
•      Verify all vehicle Head-up Display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
•      Enable satellite map for navigation (if equipped)
Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom
right-hand corner of the Navigation map screen.
On-Hoist Inspection
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers can be found in the PDI kit
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Post-Road Test Inspection
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> PDI service. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Driving Performance
•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
Effective 9-17-2018-US
Version 1.0
Model Year 2019 | Audi Pre-Delivery Reference Document | 10
A7
Technician Reference Document
Vehicle Preparation
Interior
•      Deactivate vehicle transport mode
•      Verify operation of all seat belts and latches
This step must be performed with the ignition on/engine
off or the 03 brake module may remain in transport mode.
See TSB 2042954 for resolution.
Note: The VAS 6154 diagnostic head is required along with
ODIS Audi Brand version 2.15.5 or higher. Reference TSB
2052299 for more information.
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
•      Deactivate air suspension loading mode (if equipped)
via Special Functions -> Service Work -> 34-Loading mode
activating/deactivating Warning! Car body may lower!
•      Set service reminder
via Special functions –> PDI Service –> 17-PDI-resetting SRI
at PDI, counter reset, etc.
•      Perform any open campaigns
Follow instructions listed in campaign documentation
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
•      Check all doors for proper power closing (if equipped)
For vehicles equipped with the power door closing feature,
check all doors for proper closing
Lighting and Windshield
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Verify operation of heated/ventilated and massaging seats
(if equipped)
Check both front and rear. Massaging feature is in the front
seats only (if equipped)
•      Verify proper operation of climate control*
Ensure proper heating and A/C cooling, open all panel vents
for all zones
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on”
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Setup/Settings menu
•      Verify Speech Dialog System is operating
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Set spare tire pressure
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Press the “Talk” button and verify several commands
•      Set “Music volume while parking” to medium
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Set dealership location in navigation
Set dealership location for following back to dealership
during road test
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
Effective 9-17-2018-US
Version 1.0
Model Year 2019 | Audi Pre-Delivery Reference Document | 11
A7
Technician Reference Document
Settings (continued)
Driving Performance (continued)
•      Turn off Manual Speed Warning (if equipped)
•      Verify engine performance and acceleration
This can be changed in the Driver Assistance Settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual > Select Off
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Audi connect® (USA ONLY) (if equipped)
Driver Assistance
•      Turn on the Wi-Fi® hotspot (if equipped)
•      Verify operation of parking system
Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” )
•      Check Wi-Fi® hotspot visibility. No data available at PDI
due to dealer demo mode (if equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX
is the last four digits of the VIN. Via Telephone > Options >
Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings
> Access point (SSID)
•      Enable satellite map for navigation (if equipped)
Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom
right-hand corner of the Navigation map screen.
On-Hoist Inspection
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers can be found in the PDI kit
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
•      Verify all vehicle Head-up display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
Post-Road Test Inspection
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> PDI service. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Driving Performance
•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
Effective 9-17-2018-US
Version 1.0
Model Year 2019 | Audi Pre-Delivery Reference Document | 12
A8 L
Technician Reference Document
Vehicle Preparation
Interior
•      Deactivate vehicle transport mode
•      Verify operation of all seat belts and latches
This step must be performed with the ignition on/engine
off or the 03 brake module may remain in transport mode.
See TSB 2042954 for resolution.
Note: The VAS 6154 diagnostic head is required along with
ODIS Audi Brand version 2.15.5 or higher. Reference TSB
2052299 for more information.
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
•      Deactivate air suspension loading mode (if equipped)
via Special Functions -> Service Work -> 34-Loading mode
activating/deactivating Warning! Car body may lower!
•      Set service reminder
via Special functions –> PDI Service –> 17-PDI-resetting SRI
at PDI, counter reset, etc.
•      Perform any open campaigns
Follow instructions listed in campaign documentation
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
•      Check all doors for proper power closing
For vehicles equipped with the power door closing feature,
check all doors for proper closing
Lighting and Windshield
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Set spare tire pressure
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Verify operation of heated/ventilated and massaging seats
(if equipped)
Check both front and rear. Massaging feature is in the front
seats only (if equipped)
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling, open all panel vents
for all zones
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on”
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Setup/Settings menu
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands
•      Set “Music volume while parking” to medium
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning (if equipped)
This can be changed in the Driver Assistance Settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual > Select Off
Effective 9-17-2018-US
Version 1.0
Model Year 2019 | Audi Pre-Delivery Reference Document | 13
A8 L
Technician Reference Document
Media / Radio / SAT
Driving Performance (continued)
•      Verify HD Radio is turned “off”
•      Calibrate rear view mirror
This can be found in the Radio/Settings Menu
Audi connect® (USA ONLY) (if equipped)
•      Turn on the Wi-Fi® hotspot (if equipped)
Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” )
•      Check Wi-Fi® hotspot visibility. No data available at PDI
due to dealer demo mode (if equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX
is the last four digits of the VIN. Via Telephone > Options >
Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings
> Access point (SSID)
•      Enable satellite map for navigation (if equipped)
Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom
right-hand corner of the Navigation map screen.
On-Hoist Inspection
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers can be found in the PDI kit
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
•      Verify operation of parking system
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
•      Verify all vehicle Head-up display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
Post-Road Test Inspection
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> PDI service. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Driving Performance
•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
Effective 9-17-2018-US
Version 1.0
Model Year 2019 | Audi Pre-Delivery Reference Document | 14
Q5/SQ5
Technician Reference Document
Vehicle Preparation
Trunk Inspection
•      Deactivate vehicle transport mode
•      Verify power tailgate is operational and set default opening
height
This step must be performed with the ignition on/engine
off or the 03 brake module may remain in transport mode.
See TSB 2042954 for resolution.
Note: The VAS 6154 diagnostic head is required along with
ODIS Audi Brand version 2.15.5 or higher. Reference TSB
2052299 for more information.
Deactivate vehicle transport mode (via Special functions >
Service work > 19-Transport mode activating/deactivating)
•      Deactivate air suspension loading mode (if equipped)
via Special Functions -> Service Work -> 34-Loading mode
activating/deactivating Warning! Car body may lower!
•      Set service reminder
via Special functions –> PDI Service –> 17-PDI-resetting SRI
at PDI, counter reset, etc.
•      Perform any open campaigns
Follow instructions listed in campaign documentation
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
•      Check all doors for proper power closing (if equipped)
For vehicles equipped with the power door closing feature,
check all doors for proper closing
•      Prepare the base bars for customer delivery (install bars
only upon customer request)
Install the rubber strips to the top of the base carrier bars
(do not install the carrier bars on the vehicle unless customer
has requested). Repackage the bars into the box if they are
not being installed on the vehicle. Retrieve the paper with
the torque wrench key code from the base carrier bar box.
Insert the paper with the key code into the owner’s literature
wallet. Record torque wrench key code in the VDF to ensure
it’s documented in the event the paper with the code is
misplaced
Lighting and Windshield
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Adjust the trunk lid opening height to 77.7 inches (197 cm)
from the ground to the close button in the rear lid. Press and
hold the close button in the rear lid for at least four seconds
to program the opening height
•      Install wheel bolt cover removal tool from PDI kit into
trunk lid toolkit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit to the right of the
spare tire
•      Set spare tire pressure
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Setup/Settings menu
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands
Effective 9-17-2018-US
Version 1.0
Model Year 2019 | Audi Pre-Delivery Reference Document | 15
Q5/SQ5
Technician Reference Document
Settings (continued)
Driving Performance
•      Set “Entertain. Fad.” in Parking aid to an audible level
Via “ Menu > Vehicle > Left Option > Drive Assistance > Parking Aid”
•      Verify engine Start-Stop System functionality
•      Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
•      Test drive vehicle applying brakes several times
•      Turn off Manual Speed Warning (if equipped)
This can be changed in the Driver Assistance settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual->Select Off
•      Calibrate rear view mirror
Media / Radio / SAT
Driver Assistance
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
•      Verify operation of parking system (if equipped)
Audi connect® (USA ONLY) (if equipped)
•      Verify all vehicle Head-up display functionality (if
equipped)
•      Turn on the Wi-Fi® hotspot (if equipped)
Ensure the wireless network is turned on (Telephone > Right
Option > Wi-Fi® options > Wi-Fi® “On”)
•      Check Wi-Fi® hotspot visibility. No data available at PDI (if
equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Enable Google Earth view for navigation (if equipped)
Enable Google Earth view in the Navigation > Map Settings
and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol.
On-Hoist Inspection
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Set and store tire pressures for either sold vehicle OR
stock inventory vehicle (See separate “2019 Normal Load
Condition Tire Pressure Table” posted on ServiceNet)
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Effective 9-17-2018-US
Version 1.0
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
Post-Road Test Inspection
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> PDI Service. Select option 2, the battery
test for new batteries as part of the pre–delivery inspection
and act according to the test result (ok, recharge, replace).
Ensure diagnosis log is uploaded to the GFF paperless server
by selecting “ok” when tester wants to send the current
generated diagnosis protocol online. (Note: Do not use Guided Function. The diagnosis log will not be uploaded to GFF
paperless)
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Model Year 2019 | Audi Pre-Delivery Reference Document | 16
Q7
Technician Reference Document
Vehicle Preparation
Trunk Inspection
•      Deactivate vehicle transport mode
•      Verify power tailgate is operational and set to maximum
opening height (if equipped)
This step must be performed with the ignition on/engine
off or the 03 brake module may remain in transport mode.
See TSB 2042954 for resolution.
Note: The VAS 6154 diagnostic head is required along with
ODIS Audi Brand version 2.15.5 or higher. Reference TSB
2052299 for more information.
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
•      Set service reminder
via Special functions –> PDI Service –> 17-PDI-resetting SRI
at PDI, counter reset, etc
•      Perform any open campaigns
Follow instructions listed in campaign documentation
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
•      Check all doors for proper power closing (if equipped)
For vehicles equipped with the power door closing feature,
check all doors for proper closing
•      Prepare the base bars for customer delivery (install bars
only upon customer request)
Install the rubber strips to the top of the base carrier bars
(do not install the carrier bars on the vehicle unless customer
has requested). Repackage the bars into the box if they are
not being installed on the vehicle. Retrieve the paper with
the torque wrench key code from the base carrier bar box.
Insert the paper with the key code into the owner’s literature
wallet. Record torque wrench key code in the VDF to ensure
it’s documented in the event the paper with the code is
misplaced
Lighting and Windshield
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Press and hold the close button in the rear lid for at least
four seconds to program the opening height. Verify operation
of handsfree release (if equipped)
•      Install wheel bolt cover removal tool from PDI kit into
trunk lid toolkit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit to the right of the
spare tire
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) and child safety features
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Verify operation of heated/ventilated and massaging seats
(if equipped)
Check both front and rear. Massaging feature is in the front
seats only (if equipped)
•      Verify operation of manual folding 2nd row and power
folding 3rd row seats
Controls for the power folding 3rd row are located in the
trunk
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Verify and set language and measurement units
This can be changed in the Setup/Settings menu
Effective 9-17-2018-US
Version 1.0
Model Year 2019 | Audi Pre-Delivery Reference Document | 17
Q7
Technician Reference Document
Settings (continued)
On-Hoist Inspection (continued)
•      Verify Speech Dialog System is operating
•      Set and store tire pressures for either sold vehicle OR
stock inventory vehicle (See separate “2019 Normal Load
Condition Tire Pressure Table” posted on ServiceNet)
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Press the “Talk” button and verify several commands
•      Set “Entertain. Fad.” in Parking aid to an audible level
Via “ Menu > Vehicle > Left Option > Drive Assistance > Parking Aid”
•      Set “Music volume while parking” to medium
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning (if equipped)
This can be changed in the Driver Assistance settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual >Select Off
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Driving Performance
•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Audi connect® (USA ONLY) (if equipped)
Driver Assistance
•      Turn on the Wi-Fi® hotspot (if equipped)
•      Verify operation of parking system
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Ensure the wireless network is turned on (Telephone > Right
Option > Wi-Fi® options > Wi-Fi® “On”)
•      Check Wi-Fi® hotspot visibility. No data available at PDI (if
equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Enable Google Earth view for navigation (if equipped)
Enable Google Earth view in the Navigation > Map Settings
and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol
On-Hoist Inspection
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Verify all vehicle Head-up display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
Post-Road Test Inspection
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> PDI Service. Select option 2, the battery
test for new batteries as part of the pre–delivery inspection
and act according to the test result (ok, recharge, replace).
Ensure diagnosis log is uploaded to the GFF paperless server
by selecting “ok” when tester wants to send the current
generated diagnosis protocol online. (Note: Do not use Guided Function. The diagnosis log will not be uploaded to GFF
paperless)
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Effective 9-17-2018-US
Version 1.0
Model Year 2019 | Audi Pre-Delivery Reference Document | 18
Q8
Technician Reference Document
Vehicle Preparation
Trunk Inspection (continued)
•      Deactivate vehicle transport mode
•      Install wheel bolt cover removal tool from PDI kit into
trunk lid toolkit
This step must be performed with the ignition on/engine
off or the 03 brake module may remain in transport mode.
See TSB 2042954 for resolution.
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit to the right of the
spare tire
Note: The VAS 6154 diagnostic head is required along with
ODIS Audi Brand version 2.15.5 or higher. Reference TSB
2052299 for more information.
•      Check battery clamps for proper torque
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
•      Set spare tire pressure
•      Deactivate air suspension loading mode (if equipped)
via Special Functions -> Service Work -> 34-Loading mode
activating/deactivating Warning! Car body may lower!
•      Set service reminder
via Special functions –> PDI Service –> 17-PDI-resetting SRI
at PDI, counter reset, etc
•      Perform any open campaigns
Follow instructions listed in campaign documentation
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
•      Check all doors for proper power closing (if equipped)
For vehicles equipped with the power door closing feature,
check all doors for proper closing
Lighting and Windshield
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
•      Verify power tailgate is operational and set to maximum
opening height (if equipped)
Press and hold the close button in the rear lid for at least
four seconds to program the opening height. Verify operation
of handsfree release (if equipped)
Refer to Elsa Pro for specification
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) and child safety features
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Verify operation of heated/ventilated and massaging seats
(if equipped)
Check both front and rear. Massaging feature is in the front
seats only (if equipped)
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Setup/Settings menu
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands
Effective 9-17-2018-US
Version 1.0
Model Year 2019 | Audi Pre-Delivery Reference Document | 19
Q8
Technician Reference Document
Settings (continued)
Driving Performance
•      Set “Music volume while parking” to medium
•      Verify engine Start-Stop System functionality
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning (if equipped)
This can be changed in the Driver Assistance settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual >Select Off
Media / Radio / SAT
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect® (USA ONLY) (if equipped)
•      Turn on the Wi-Fi® hotspot (if equipped)
Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” )
•      Check Wi-Fi® hotspot visibility. No data available at PDI
due to dealer demo mode (if equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX
is the last four digits of the VIN. Via Telephone > Options >
Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings
> Access point (SSID)
•      Enable satellite map for navigation (if equipped)
Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom
right-hand corner of the Navigation map screen.
On-Hoist Inspection
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Set and store tire pressures for either sold vehicle OR
stock inventory vehicle (See separate “2019 Normal Load
Condition Tire Pressure Table” posted on ServiceNet)
Driver Assistance
•      Verify operation of parking system
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
•      Verify all vehicle Head-up display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
Post-Road Test Inspection
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> PDI Service. Select option 2, the battery
test for new batteries as part of the pre–delivery inspection
and act according to the test result (ok, recharge, replace).
Ensure diagnosis log is uploaded to the GFF paperless server
by selecting “ok” when tester wants to send the current
generated diagnosis protocol online. (Note: Do not use Guided Function. The diagnosis log will not be uploaded to GFF
paperless)
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Effective 9-17-2018-US
Version 1.0
Model Year 2019 | Audi Pre-Delivery Reference Document | 20
TT Coupe & Roadster/TTS/TT RS
Technician Reference Document
Vehicle Preparation
Interior (continued)
•      Deactivate vehicle transport mode
•      Inspect operation of all power outlets
This step must be performed with the ignition on/engine
off or the 03 brake module may remain in transport mode.
See TSB 2042954 for resolution.
Deactivate vehicle transport mode (via Special functions >
PDI service > 19-Transport mode activating/deactivating.)
•      Set service reminder
via Special functions –> PDI service –> 17-PDI-resetting SRI
at PDI, counter reset, etc
•      Perform any open campaigns
Follow instructions listed in campaign documentation
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Set spare tire pressure (NA for TT RS)
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet under Pre-Delivery Inspection
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
Effective 9-17-2018-US
Version 1.0
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Settings menu by going to Menu >
Vehicle > Vehicle settings
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands
•      Set “Entertain. Fad.” in Parking aid to an audible level
Via “Menu > Vehicle > Left Option > Driver Assistance > Parking Aid”
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning (if equipped)
This can be changed in the Driver Assistance settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual->Select Off
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect® (USA ONLY) (if equipped)
•      Turn on the Wi-Fi® hotspot (if equipped)
Ensure the wireless network is turned on (Telephone > Right
Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot”)
•      Check Wi-Fi® hotspot visibility. No data available at PDI (if
equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
Access point (SSID) is set to “Audi_MMI__XXXX,” where XXXX
is the last four digits of VIN. Via Telephone > Options > WiFi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings >
Access point (SSID)
•      Enable Google EarthTM view for navigation (if equipped)
Enable Google EarthTM in the Navigation > Map Settings and
verify the white Google logo appears in the bottom right
hand corner of the MMI screen next to the LTE symbol
Model Year 2019 | Audi Pre-Delivery Reference Document | 21
TT Coupe & Roadster/TTS/TT RS
Technician Reference Document
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Driving Performance
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/vibration/pulsation
Driver Assistance
•      Verify operation of Audi parking system plus (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Roadster Functionality (if equipped)
•      Test operation of power folding top
Perform with engine running to conserve battery power
Post-Road Test Inspection
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> PDI service. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Effective 9-17-2018-US
Version 1.0
Model Year 2019 | Audi Pre-Delivery Reference Document | 22