B512017
Service Bulletin Details
Public Details for: B512017
"window frame trim of front door is displaced. ? Noise detected upon closing door ? Damage to one or both window frame trims (front and rear door). Cause front window frame trim is offset toward ""b"" pillar (as shown). Replace one or bot
- 2016 - 2015 - 2014 - 2013 - 2012 - 2011 -
Models from 2016
2016 BMW 528I |
2016 BMW 535D |
2016 BMW 535I |
2016 BMW 550I |
2016 BMW M5 |
Models from 2015
2015 BMW 528I |
2015 BMW 535D |
2015 BMW 535I |
2015 BMW 550I |
2015 BMW M5 |
Models from 2014
2014 BMW 525D XDRIVE |
2014 BMW 528I |
2014 BMW 535D |
2014 BMW 535I |
2014 BMW 550I |
2014 BMW M5 |
Models from 2011
2011 BMW 528I |
2011 BMW 535I |
2011 BMW 535I US |
2011 BMW 550I |
Page 1 of 3 SI B51 20 17 Body Equipment May 2017 Technical Service WINDOW FRAME TRIM OF FRONT DOOR IS DISPLACED MODEL F10 (5 Series) SITUATION • Noise detected upon closing door • Damage to one or both window frame trims (front and rear door). CAUSE Front window frame trim is offset toward “B” pillar (as shown). Frame trim damage may be caused by trim overlap. CORRECTION Replace one or both window frame trim panels, if damaged. PROCEDURE For conditions that are similar to the situation described: Note: Apply adhesive tape to prevent damage to the window frame panels. 1. Remove window frame according to repair instructions “51 32 390 Removing and installing/replacing frame trim on front left or right side window frame” 2. Clean the window frame surface at the three rear clamp positions as depicted in picture. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/417... 6/5/2017 Page 2 of 3 3. Apply adhesive tape on the window frame (83 19 0411397 – Fabric tape, Tesa 4657) at the 3 positions shown. 4. Re-install the window trim and any other removed parts according to appropriate repair instructions Note: Be careful when separating the layers to minimize any marring of the surfaces. PARTS INFORMATION Part Number Description Quantity 83 19 0 411 397 Fabric Tape, Tesa 4657 (L=50m, W=12mm) As needed WARRANTY INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks. Defect Code: 5133194100 Repairing One Side Labor Operation: Labor Allowance: Description: 51 32 390 Refer to KSD2 Removing and installing or replacing ornamental frame on window frame of left or right front door (Main work) Refer to KSD2 Removing and installing or replacing ornamental frame on window frame of left or right front door (Plus work) 2 FRU Cleaning and applying fabric tape to window frame panel (one side) Or: 51 32 890 And: 51 99 000 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/417... 6/5/2017 Page 3 of 3 If you are using a Main labor code for another repair, use the Plus code labor operation 51 32 890 instead. Or Repairing Both Sides Labor Operation: Labor Allowance: Description: 51 32 391 Refer to KSD2 Removing and installing or replacing ornamental frame on window frame on both front doors Refer to KSD2 Removing and installing or replacing ornamental frame on window frame on both front doors 4 FRU Cleaning and applying fabric tape to window frame panel (both sides) (Main work) Or: 51 32 891 (Plus work) And: 51 99 000 If you are using a Main labor code for another repair, use the Plus code labor operation 51 32 891 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowances. Work time labor operation code 51 99 000 is not considered a Main labor operation. Also, since the “work time” FRU allowance to be claimed is specified, a separate punch time is not required. And: Sublet – Bulk Materials Sublet Code 4 See sublet reimbursement calculation below Reimbursement for the repair-related bulk material (BMW part number, please do not use the part numbers for claim submission) Sublet reimbursement calculation for claiming the “used quantities” of repair-related bulk material (BMW part number) is at dealer net plus your center’s handling. Enter this material cost in sublet and itemize the amount on the repair order and in claim comment section Overlapping Labor Procedure – Other Repairs If invoicing the KSD2 flat rate labor operation codes for other repair work results in overlapping labor, for those flat rate labor operations that are affected, you can now: • Replace the stated KSD2 “FRU allowance” with a “reduced FRU value” to eliminate the overlapping labor. For help in identifying the overlapping labor, please refer to the AIR FRU Plausibility Check (Overlapping Labor Tool) that is located in the AIR Client. Eligible other repair work being claimed under a different defect code will require separate punch times. On the repair order and in the claim comment section, please identify and itemize those labor operations being claimed with a “reduced FRU value.” [ Copyright ©2017 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/417... 6/5/2017