07-007-15
Service Bulletin Details
Public Details for: 07-007-15
Vibration felt in steering wheel this bulletin involves applying aluminium adhesive tape around the radiator anchoring pin. The customer may describe a vibration that is felt in the steering wheel. A vibration may be caused by clearance
- 2015 -
Models from 2015
2015 JEEP RENEGADE |
NUMBER: GROUP: DATE: 07-007-15 Cooling October 09, 2015 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC. SUBJECT: Vibration Felt In Steering Wheel OVERVIEW: This bulletin involves applying aluminium adhesive tape around the radiator anchoring pin. MODELS: 2015 (BU) Jeep Renegade NOTE: This bulletin applies to vehicles within the following markets/countries: NAFTA, EMEA NOTE: This bulletin applies to vehicles built on or before May 26, 2015 (MDH 0526XX) WITHOUT Transmission Skid Plate (Sales Code XE9). SYMPTOM/CONDITION: The customer may describe a vibration that is felt in the steering wheel. A vibration may be caused by clearance between the radiator anchoring pin and radiator support rubber bushing. DIAGNOSIS: If the customer describes the symptom/condition listed above, perform the Repair Procedure. PARTS REQUIRED: Qty. Part No. Description 1 (AR) NPN 3M™ Aluminum Foil Adhesive Tape 3381 (or equivalent) NOTE: Each roll of aluminum foil adhesive tape will service approximately 100 vehicles (Shop Supply, Not on Claim). 07-007-15 -2- REPAIR PROCEDURE: 1. Raise the vehicle. Refer to the detailed service procedures available in DealerCONNECT> TechCONNECT under: Service Info> 04 - Vehicle Quick Reference> Hoisting> Standard Procedure. 2. Remove the lower fasteners (1 and 2) from the front bumper fascia lower edge (Fig. 1). Fig. 1 Remove Front Bumper Fascia Lower Edge Fasteners 1 - Bolts 2 - Screws 3. Use a wood block (1) or equivalent to hold the front bumper fascia lower edge down in order to access the radiator support brackets (Fig. 2). -3- 07-007-15 Fig. 2 Use Wood Block To Provide Access 1 - Wood Block 4. Remove the bolts (1) from the radiator support brackets (2) on both the right and left sides of the vehicle and remove the brackets (Fig. 3). Fig. 3 Remove Radiator Support Brackets 1 - Bolt 2 - Support Bracket 07-007-15 -4- 5. With the radiator support brackets off-vehicle, remove the rubber bushing (1) from the bracket (2), repeat for both brackets (Fig. 4). Fig. 4 Remove Bushings From Brackets 1 - Rubber Bushing 2 - Support Bracket 6. Cut four pieces of aluminum foil adhesive tape to 20 mm x 20 mm (Fig. 5). Fig. 5 Cut Tape Pieces To Size 1 - Aluminum Foil Adhesive Tape Pieces -5- 07-007-15 7. Apply two pieces of aluminium adhesive tape (1) to each bracket (2), one piece on the fore and one piece on the aft sides of the bushing openings (Fig. 6). 8. Install the rubber bushing (3) into the bracket (2), repeat for both brackets (Fig. 6). Fig. 6 Install Tape And Bushings To Brackets 1 - Aluminum Foil Adhesive Tape 2 - Support Bracket 3 - Rubber Bushing 9. Cut pieces of aluminum foil adhesive tape to 30 mm x 38 mm. NOTE: Approximately four pieces may be required. Actual number of pieces will be determined by the thickness of the aluminium foil adhesive tape used. 10. On the left side only, wrap the aluminium foil adhesive tape pieces (2) around the round anchoring pin (1) in order to increase the pin diameter (3) by 1 mm (Fig. 7). 07-007-15 -6- Fig. 7 Wrap Tape Around Anchoring Pin 1 - Anchoring Pin 2 - Aluminum Foil Adhesive Tape 3 - Measuring Caliper 11. Install the radiator support brackets (2) and secure with bolts (1) on both the right and left sides of the vehicle (Fig. 8). Fig. 8 Install Radiator Support Brackets 1 - Bolt 2 - Support Bracket -7- 07-007-15 12. Remove the wood block and install the fasteners (1 and 2) securing the front bumper fascia lower edge (Fig. 9). Fig. 9 Install Front Bumper Fascia Lower Edge Fasteners 1 - Bolts 2 - Screws 13. Lower the vehicle. POLICY: Reimbursable within the provisions of the warranty. TIME ALLOWANCE: Labor Operation No: 07-14-01-90 Description Repair Both Lower Radiator Mounting Brackets and Apply Tape to Left Radiator Pin (0 - Introduction) FAILURE CODE: ZZ Service Action Skill Category 6 - Electrical and Body Systems Amount 0.5 Hrs.