T-SB-0177-16

Prius C
UNDER VEHICLE (ON HOIST)
1 Remove disc brake anti-rust covers/anti-corrosion
wheel film* (Remove just prior to customer delivery)….…..
2 Inspect tires for defects/damage.……………………………..
3 Initialize Tire Pressure Warning System (TPWS)
(see page 2).........................................................................
4 Install wheel caps*.…………………………………….……….
5 Install front wheel opening extension pads (see page 2).….
6 Inspect for fuel, oil, coolant, and other fluid leaks.…………..
7 Inspect under the vehicle for damage, rust, etc..……………
8 Visually check bolts and nuts on chassis and powertrain
for looseness…..………………………………………………..
9 Install rubber body plugs (stored in glove box or
center console)*…………………………………………………
10 Check hybrid transaxle fluid level……..………………………
1 Install D/C Cut Fuse (see page 2).........................................
FUNCTIONAL OPERATION
Apply parking brake and cycle ignition “IG-ON”; place gear selector in reverse; turn
on lights and rear defogger. Unlock all doors and release fuel door.
1
2
3
4
5
6
7
8
9
Check dome, courtesy, map, and sun visor lights*………....
Check warning/indicator lights, buzzers, and horn.…..……..
Check windshield wipers and washers..……………………..
Check headlights, instrument lights, dimmer switch, turn
signals, emergency flashers, and brake lights……………….
Check inside/outside rear view mirror
operation/adjustment*…………………………………………..
Check cigarette lighter* and power outlets…………………..
Check audio/navigation*/backup camera* systems and
set clock…………………….……………………………………
Check multi-information display and trip information on
center display*…………………………………………………..
Check sliding roof*.……………………………………………..
ROAD TEST
A complete road test helps assure customer satisfaction. Drive vehicle over a
variety of road surfaces and driving conditions. Check for unusual noise and
driving performance.
WALKAROUND INSPECTION
Enter Odometer Readings
Start at left front door. Check window and door lock operation (from master power
switch, if equipped). Continue around vehicle in a counterclockwise direction
checking each door and window operation, child door locks, seat belts, interior
condition, all lights, luggage compartment contents. Finish by checking headlight
aim and continue into UNDER HOOD checks.
Reading Before Test: _______________ Reading After Test: ________________
1
2
3
4
5
6
1 Check Smart Key System*……………………………...…...
2 Check door and door lock operation, including each
wireless remote control/theft deterrent system*……………..
3 Check window operation……………………………………….
4 Check that engine starts with all keys.……………….………
5 Check that child safety door locks are in normal
(unlocked) position*...……………………………………….….
6 Check seats and seat belt operation………………………....
7 Check rear defogger/rear view mirror defogger*…………….
8 Check side marker, tail, backup, and license plate lights.….
9 Check luggage compartment light* and trim appearance….
10 Adjust spare tire pressure, inspect for damage, and check
jack and tool installation………………………………………..
11 Check headlight aim…………………………………………....
12 Check battery State-Of-Charge using Digital Battery
System Analyzer (SOC Reading: ___________%)……….
7
8
9
10
11
Check cold engine operation.………………………………….
Check engine operation during warm-up.……………………
Check engine operation at normal operating temperature…
Check hybrid transaxle operation..…………………………....
Check brake and parking brake operation.…………………..
Check steering operation and off-center/vehicle
pull/flutter…………………………………………………………
Inspect for abnormal noise and vibration.……………………
Inspect for squeaks and rattles.……………………………….
Check heater and A/C operation.……………………………..
Check cruise control operation*.……………………………....
Check front seat heater/ventilation operation*.……………...
FINAL INSPECTION AND CLEANING
1 Remove interior protective covers, unnecessary labels,
tags, etc. (Remove just before delivery to customer).………
2 Visually inspect all interior parts for installation, damage,
fit, dirt, etc.…………………………………………………...…..
3 Verify floor mat application and install using
retaining clips*…..…………………………………………….
4 Remove Rapgard™ and clear protective bumper film*….…
5 Wash and clean vehicle…………………………………….….
6 Inspect paint finish for scratches, chips, rust, dents,
damage, etc……………………………..………………………
7 Place oil change sticker on inside of windshield, top
left corner………………..………………………………………
8 Inspect exterior body parts for proper installation, damage,
rust, etc…………………………………………………………..
9 Install front license plate and mounting bracket*
(see page 2)…………………………………………………….
10 Place Owner’s Manual portfolio* in glove box……………….
11 Perform Techstream Health Check……………………………
UNDER HOOD
1
2
3
4
5
6
OK
BEFORE INSPECTION
December 2016
Adjust\
Repair
OK
2017 PRE-DELIVERY SERVICE CHECK SHEET
Adjust\
Repair
Market: USA
Check engine oil level…………………………………………..
Check brake and power steering fluid levels….….………….
Check engine coolant level.……………………………………
Check inverter coolant level.…………………………………..
Check windshield washer fluid level…………………………..
Inspect for fuel, oil, coolant, and other fluid leaks…………...
BATTERY MAINTENANCE
1 Perform HV battery check and maintenance……………..
Notes:
* Inspect or install when equipped/required.
Completion and retention of this form is required to comply with Toyota’s Warranty Policy.
TECHNICIAN’S SIGNATURE
NAME (PLEASE PRINT)
Date
Dealer Name
SERVICE MANAGER’S SIGNATURE
We hereby certify that all items
on this form have been
checked and corrected for
proper operation as required.
NAME (PLEASE PRINT)
Dealer Code
Vehicle Identification Number (Sticker)
D/C CUT FUSE INSTALLATION
The D/C Cut Fuse (30 A) has been removed at the assembly plant to
reduce parasitic current draw in transit and storage. Reinstall the D/C Cut
Fuse to the original location.
1
2
1 Storage Location
2 Installation Location
TIRE PRESSURE WARNING SYSTEM (TPWS INITIALIZATION)
Refer to the Repair Manual for the Initialization procedure. Please note the spare tire does NOT have a TPWS sensor.
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder than shop temperature, perform a
Health Check using Techstream and select the “Compensation Tire Pressure” checkbox. Compensation pressures will be
displayed on the Health Check results screen. Adjust the tire pressure when the tires are cold.
FRONT WHEEL OPENING EXTENSION PAD INSTALLATION
The front wheel opening extension pad set (right and left front wheel opening
extension pads and 4 self-tapping screws) is loaded in the luggage
compartment at the assembly plant to avoid damage in transit.
1. Hook the retainers of the front left wheel opening extension pad through
the installation holes on the fender liner and temporarily fix it to the
installation position.
NOTE
There is a distinguishable mark on each pad.
2. Tighten the 2 self-tapping screws.
3. Repeat for the right side.
FRONT LICENSE PLATE AND MOUNTING BRACKET INSTALLATION*
1. Align the installation holes of the front license plate and mounting
bracket with the dimples on the front bumper.
NOTICE
Do NOT pre-drill holes into the bumper.
Do NOT overtighten the self-tapping screws.
1
2
2. Using 2 self-tapping screws, install the front license plate and mounting
bracket by directly screwing the self-tapping screws into the dimples.
Length: 15.0 – 20.0 mm (0.60 – 0.79 in.)
Diameter: 6.0 mm (0.24 in.)
3
1 Dimples
2 License Plate
3 Self-tapping Screws