B070218

TIS Service Bulletin
Page 1 of 3
SI B07 02 18
Diagnosis
November 2018
Technical Service
STATUS OF FAULT CODES IN ISTA FOR G05/G15
MODEL
G05 (X5)
G15 (8 Series Coupe)
SITUATION
After programming it could be that some fault codes cannot be deleted even after a sleep cycle of the vehicle.
CAUSE
Some of these errors are erroneous faults, which can be ignored. Some of the faults are still under
investigation.
Refer to the table below which shows a list of fault codes, a short description and how to deal with it.
CORRECTION
Please see table for further information.
Fault Code
Fault Description
Correction
0x030215
FZD (Function Center Roof Module) loses
Sliding/tilt sunroof: No initialization
initialization when it is programmed.
due to invalid normalization
Perform service function in ISTA (part of
values
therapy plan) for S18A
0x031E31
RAM: Manipulation of Adjustment
Block detected
Please ignore – fault code won´t be
displayed with ISTA 4.15.2x
0x801C90
ZGM: OBD firewall not initialized
Fault code is set correctly - the OBD firewall
will only be initialized after PDI /
provisioning
0x8029CA
Still under investigation; most likely a
SMFA: Seat position not send due problem with the internal Bootloader Update
to missing or invalid calibration
of the seat modules (loss of initialization
data); Workaround: perform seat calibration
0x802A05
SMFA: Locking protection switchoff due to missing calibration
Still under investigation; most likely a
problem with the internal Bootloader Update
of the seat modules (loss of initialization
data); Workaround: perform seat calibration
0x802A29
Driver`s seat module, backrest
angle adjustment: restricted
Still under investigation; most likely a
problem with the internal Bootloader Update
https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/48... 12/3/2018
TIS Service Bulletin
Page 2 of 3
adjustment due to lack of
calibration
of the seat modules (loss of initialization
data); Workaround: perform seat calibration
0x802A2A
Driver`s seat module, headrest
height adjustment: restricted
adjustment due to lack of
calibration
Still under investigation; most likely a
problem with the internal Bootloader Update
of the seat modules (loss of initialization
data); Workaround: perform seat calibration
0x802BCA
SMBF: Seat position not sent due
to missing or invalid calibration
Still under investigation; most likely a
problem with the internal Bootloader Update
of the seat modules (loss of initialization
data); Workaround: perform seat calibration
0x802C05
SMBF: Locking protection switchoff due to missing calibration
Still under investigation; most likely a
problem with the internal Bootloader Update
of the seat modules (loss of initialization
data); Workaround: perform seat calibration
0x802C29
Front passenger seat module,
backrest angle adjustment:
restricted adjustment due to lack
of calibration
Still under investigation; most likely a
problem with the internal Bootloader Update
of the seat modules (loss of initialization
data); Workaround: perform seat calibration
0x802C2A
Front passenger seat module,
backrest height adjustment:
restricted adjustment due to lack
of calibration
Still under investigation; most likely a
problem with the internal Bootloader Update
of the seat modules (loss of initialization
data); Workaround: perform seat calibration
0x802C2C
SMBF: No preventive seat
adjustment due to missing
calibration
Still under investigation; most likely a
problem with the internal Bootloader Update
of the seat modules (loss of initialization
data); Workaround: perform seat calibration
0x8042A0
Windshield wiper (LIN): Coding
invalid
Problem with LIN startup; should be
possible to delete after sleep cycle; in some
cases, another coding of the BDC (Body
Domain Controller) is necessary
0xB7F8C5
CID hardware error: error in flash
data checksum
Please ignore – fault code won´t be
displayed with ISTA 4.15.2x
0xB7F8FB
HU-H: invalid certification block
list
This problem is caused by the IT backend
and can´t be fixed in the car; please ignore
OR create an IT ticket
0xCD9763
Message (request, rear axle
speed, 69.3.4) missing, receiver
DDE, transmitter DSC
Please ignore – fault code won´t be
displayed with ISTA 4.15.2x
0xCD9767
Message (request, front axle
speed, 69.3.4) missing, receiver
DDE, transmitter DSC
Please ignore – fault code won´t be
displayed with ISTA 4.15.2x
0xCD990B
FlexRay, message (request, rear
axle RPM, 69.3.4): Missing
Please ignore – fault code won´t be
displayed with ISTA 4.15.2x
0xCD990E
FlexRay, message (request, front
axle RPM, 69.3.4): Missing
Please ignore – fault code won´t be
displayed with ISTA 4.15.2x
https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/48... 12/3/2018
TIS Service Bulletin
Page 3 of 3
0xD90D54
NFC Reader, inside front:
Unexpected CAN user
Still under investigation; please ignore if
system is working properly
0xE10602
Instrument cluster: Ethernet: Poor
signal quality
Please ignore – fault code won´t be
displayed with ISTA 4.15.2x
0xE12C4D
Signal (roadway inclination,
0x163) invalid, transmitter DSC
Please ignore – fault code won´t be
displayed with ISTA 4.15.2x
[ Copyright ©2018 BMW of North America, Inc. ]
https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/48... 12/3/2018