TSBELE154

GROUP
ELE
MODEL
2019MY
Sorento (UMa)
NUMBER
154
DATE
December 2018
TECHNICAL SERVICE BULLETIN
SUBJECT:
BCW LOGIC IMPROVEMENT FOR DTC C270254
This bulletin provides the procedure to improve the logic of the Blind Spot Collision Warning
(BCW) system on some 2019MY Sorento (UMa) vehicles, produced from January 22, 2018
through September 22, 2018, which may experience a Malfunction Indicator Lamp (MIL)
illumination with DTC C270254, even though there is no issue or defective part. To correct this
concern, apply the improved logic to the BCW using the KDS ECU Upgrade function as
described in this bulletin. For confirmation that the latest reflash has been applied to a vehicle
you are working on, verify the ROM ID using the table on page 2 of this bulletin.
DTC C270254: Control Module Master Missing Calibration
Kia Diagnostic System (KDS)
File Under: 
Circulate To:
X General Manager

X Service Advisors

X Technicians

X Service Manager

X Parts Manager

X Body Shop Manager  Fleet Repair

Page 2 of 8
SUBJECT:
BCW LOGIC IMPROVEMENT FOR DTC C270254
ECU Upgrade Procedure:
To correct this condition, the ECU should be reprogrammed using the KDS
download, as described in this bulletin.
Upgrade Event Name
378. UMA PE BCW MIL ON DTC (C270254) LOGIC IMPROVEMENT
 NOTICE







A fully charged battery is necessary before ECU upgrade can take place. It is
recommended that the Midtronics GR8-1299 system be used in ECU mode during
charging. DO NOT connect any other battery charger to the vehicle during ECU
upgrade.
All ECU upgrades must be done with the ignition key in the ‘ON’ position.
Be careful not to disconnect the VCI-II connected to the vehicle during the ECU
upgrade procedure.
DO NOT start the engine during ECU upgrade.
DO NOT turn the ignition key ‘OFF’ or interrupt the power supply during ECU
upgrade.
When the ECU upgrade is completed, turn the ignition ‘OFF’ and wait 10 seconds
before starting the engine.
ONLY use approved ECU upgrade software designated for the correct model,
year.
 NOTICE
Before attempting an ECU upgrade on any Kia model, make sure to first determine
whether the particular model is equipped with an immobilizer security system.
Failure to follow proper procedures may cause the PCM to become inoperative after
the upgrade and any claims associated with this repair may be subject to
chargeback.
ROM ID INFORMATION TABLE:
Upgrade Event #378
Model
System
IMMO
Part No.
ROM ID
Previous
New
UM11UM11
95811 C6500
UMa
BCW
UM21UM11
UM21UM21
95821 C6500
UM11UM21
To verify the vehicle is affected, be sure to check the Calibration Identification of the vehicle's ECM
ROM ID and reference the Information Table as necessary.
TSB: ELE154 Sorento (UMa) December 2018
Page 3 of 8
BCW LOGIC IMPROVEMENT FOR DTC C270254
SUBJECT:
 NOTICE
Prior to performing the ECU upgrade, be sure to check that the KDS is fully charged.
1.
Connect the VCI-II to the OBD-II
connector, located under the driver’s side
of the instrument panel.
 NOTICE
The ECU upgrade function on
KDS operates wirelessly. It is
not necessary to perform the
upgrade via USB cable.
2.
With the ignition ON, turn ON the KDS
tablet. Select KDS from the home
screen.
3.
Confirm communication with VCI (A) and
then configure the vehicle (B) using the
AUTO VIN (C) feature.
B
A
C
4.
Select ECU Upgrade.
TSB: ELE154 Sorento (UMa) December 2018
Page 4 of 8
SUBJECT:
5.
BCW LOGIC IMPROVEMENT FOR DTC C270254
The KDS will check the server for
recently uploaded Events and then
automatically download Upgrade Event
#378.
 NOTICE
The vehicle must be identified in
Vehicle Selection to download
an Event for that vehicle.
6.
KDS
screenshot
shown
above
is
for
demonstration purposes only. Events shown in
screenshot are not applicable to this bulletin.
Select Auto Mode.
CAUTION
Do NOT attempt to perform a
Manual Mode upgrade UNLESS
Auto Mode fails. Always follow
the instructions given on the
KDS in either Auto or Manual
mode.
7.
Select the BCW system under the
System selection menu.
Touch ID Check (D) and confirm that the
latest update is available.
D
Select Upgrade Event #378 and select
Upgrade to continue.
8.
The ECU upgrade will begin and the
progress of the upgrade will appear on
the bar graph. Upgrade part (1/2) (E) will
download the upgrade event to the VCIII. Upgrade part (2/2) (F) will upgrade the
ECU.
CAUTION
Do not touch the system
buttons (like ‘Back’, ‘Home’,
‘etc.’) while performing ECU
Upgrade.
TSB: ELE154 Sorento (UMa) December 2018
E
F
Page 5 of 8
SUBJECT:
9.
BCW LOGIC IMPROVEMENT FOR DTC C270254
If a “Communication Fail” screen
appears, verify that the VCI-II and KDS
are communicating properly. Touch OK
and restart the procedure from step 4.
 NOTICE
If an error notice continues to
appear or if the upgrade cannot
be
performed,
DO
NOT
disconnect
the
KDS/VCI-II.
Contact GIT America Help Desk
at (888) 542-4371 or Techline.
10. When instructed on the KDS, turn the
ignition OFF for ten (10) seconds then
back on. Touch OK to continue.
11. Once the upgrade is complete, touch OK
to finalize the procedure.
12. When prompted, select YES to check for
Diagnostic Trouble Codes (DTC) and
erase any DTCs stored such as EPS,
ESC, and TPMS that may have been set
during the upgrade.
TSB: ELE154 Sorento (UMa) December 2018
Page 6 of 8
SUBJECT:
BCW LOGIC IMPROVEMENT FOR DTC C270254
13. At the KDS Home Screen, select S/W
Management → Blind-Spot Collision
Warning → BCW(BSD) Variant Coding
and perform the BCW(BSD) Variant
Coding.
14. After performing BCW(BSD) Variant
Coding, perform BCW(BSD) Radar
Calibration (without calibration device).
15. Start the engine and confirm proper
operation of the vehicle.
TSB: ELE154 Sorento (UMa) December 2018
Page 7 of 8
SUBJECT:
BCW LOGIC IMPROVEMENT FOR DTC C270254
Manual Upgrade Procedure:
 NOTICE
The manual upgrade should ONLY be performed if the automatic upgrade fails.
If the automatic upgrade fails, turn the ignition OFF for about 10 seconds then place
it back in the ON position to reset the control unit BEFORE performing manual
upgrade.
See table below for Manual Mode passwords.
Manual Mode ECU Upgrade Passwords
Menu
Password
UMA PE BCW : 95811/21-C6500
6500
1.
Within the ECU Upgrade screen displayed, select Manual Mode.
2.
Select the BCW system under the System selection menu. Select Upgrade Event #378
and select Upgrade to continue.
3.
Select the appropriate control unit part number with reference to the ROM ID Information
Table on page 2 and select OK.
4.
Enter the appropriate password from the Manual Mode password table above and select
OK.
5.
The upgrade will begin and the progress of the upgrade will appear on the bar graph.
6.
When instructed on the KDS, turn the ignition OFF for ten (10) seconds then back on.
Touch OK to continue.
7.
Once the upgrade is complete, touch OK to finalize the procedure.
8.
When prompted, select YES to check for Diagnostic Trouble Codes (DTC) and erase any
DTCs stored such as EPS, ESC, and TPMS that may have been set during the upgrade.
9.
At the KDS Home Screen, select S/W Management → Blind-Spot Collision Warning →
BCW(BSD) Radar Calibration and calibrate the BCW radar without the calibration device.
10. After performing the BCW(BSD) Radar Calibration, perform the BCW(BSD) Variant
Coding.
11. Start the engine and confirm proper operation of the vehicle.
TSB: ELE154 Sorento (UMa) December 2018
Page 8 of 8
SUBJECT:
BCW LOGIC IMPROVEMENT FOR DTC C270254
AFFECTED VEHICLE RANGE:
Model
Production Date Range
Sorento (UMa)
January 22, 2018 through September 22, 2018
WARRANTY INFORMATION:
N Code: I3A C Code: ZZ3
Claim
Type
Causal P/N
Qty.
Repair
Description
Labor Op
Code
Op
Time
Replacement
P/N
Qty.
W
95821 C6500
0
BCW Logic Improvement
for DTC C270254
95811F01
0.5
M/H
N/A
0
TSB: ELE154 Sorento (UMa) December 2018