A19-034

Service Bulletin
19-034
April 6, 2019
Version 1
2013-15 Accord: Engine Will Not Start with DTC P2101
AFFECTED VEHICLES
Year
Model
Trim
VIN Range
2013-15
Accord (L4 only)
ALL (KL) (L4 only)
ALL
SYMPTOM
The engine will not start and sets DTC P2101 (electronic throttle control system [ETCS] malfunction).
POSSIBLE CAUSES
The throttle body contains heavier than normal carbon buildup.
CORRECTIVE ACTION
Update the PGM-FI software.
WARRANTY CLAIM INFORMATION
The normal warranty applies.
Operation
Number
Description
Flat Rate
Time
Defect
Code
Symptom
Code
Template
ID
Failed Part Number
1255D8
Update the PGM-FI
software.
0.2 hr
03214
03217
A19034A
37805-5A3-325
A
Do the PCM idle learn
procedure - add
0.1 hr
Skill Level: Repair Technician
CUSTOMER INFORMATION:The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and
training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume
this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an
authorized Honda automobile dealer.
©
2019 American Honda Motor Co., Inc. — All Rights Reserved
Page 1 of 7
SOFTWARE INFORMATION
NOTE
Unnecessary or incorrect repairs resulting from a failure to update the i-HDS are not covered under warranty.
i-HDS Software Version: 1.004.064 or later
J2534 Software Information:
•
PC Application Version 1.1.0.6 or later
•
Database update 12-MAR-2019 or later
Before beginning the repair, make sure that both the i-HDS and J2534 software are updated as listed above.
Do only the update listed in this service bulletin.
For more information about updating the i-HDS, the MVCI, and vehicle systems, refer to service bulletin 01-023,
Updating Control Units/Modules.
Year/Model
Software
System
Program ID (or later)
Program P/N (or later)
2013 Accord 4-door LX with
CVT
PGM-FI
A33250
37805-5A3-325
2013 Accord 4-door EX, EX-L,
EX-L (Navi) with CVT
PGM-FI
A33260
37805-5A3-326
2013 Accord 4-door Sport with
CVT
PGM-FI
A33270
37805-5A3-327
2014 Accord 4-door LX with
CVT
PGM-FI
A3L130
37805-5A3-L13
2014 Accord 4-door EX, EX-L,
EX-L (Navi) with CVT
PGM-FI
A3L230
37805-5A3-L23
2014 Accord 2-door LX-S with
CVT
PGM-FI
A3L330
37805-5A3-L33
2014 Accord 4-door Sport with
CVT
PGM-FI
A3L330
37805-5A3-L33
2014 Accord 2-door EX, EX-L,
EX-L (Navi) with CVT
PGM-FI
A3L430
37805-5A3-L43
2015 Accord 4-door LX with M/T PGM-FI
A0L050
37805-5A0-L05
2015 Accord 4-door Sport with
M/T
PGM-FI
A0L050
37805-5A0-L05
2015 Accord 4-door EX with M/T PGM-FI
A0L150
37805-5A0-L15
2015 Accord 4-door LX with
CVT
PGM-FI
A1L560
37805-5A1-L56
2015 Accord 4-door EX, EX-L,
EX-L (Navi) with CVT
PGM-FI
A1L660
37805-5A1-L66
2015 Accord 2-door LX-S with
CVT
PGM-FI
A1L760
37805-5A1-L76
Page 2 of 7
Year/Model
Software
System
Program ID (or later)
Program P/N (or later)
2015 Accord 4-door Sport with
CVT
PGM-FI
A1L760
37805-5A1-L76
2015 Accord 2-door EX, EX-L,
EX-L (Navi)with CVT
PGM-FI
A1L860
37805-5A1-L86
REPAIR PROCEDURE
NOTE
•
Connect a fully charged jumper battery to the vehicle, and leave it connected during the entire procedure to maintain
steady voltage.
•
Never turn the ignition to OFF or ACCESSORY during the update. If there is a problem with the update, leave the
ignition turned to ON.
•
To prevent control unit damage, do not operate anything electrical (headlights, audio system, brakes, A/C, power
windows, door locks, etc.) during the update.
•
Do not use the MongoosePro VCI tool.
1. Select the i-HDS icon from the Desktop.
2. On the HOME menu, select J2534 Rewrite icon.
Page 3 of 7
3. Select Start. Do not enter a service bulletin number.
NOTE
Under certain conditions the HOME menu screen may pop back up, if it does, just minimize the screen to show the
screen below.
Page 4 of 7
4. Connect to a vehicle and select Start to begin reprogramming.
5. Follow the screen prompts, then select Next.
Page 5 of 7
6. Enter the VIN and repair order. Then select Next.
7. Select the system you want to update, then Select.
NOTE
Wait until vehicle communication has completed.
Page 6 of 7
8. Confirm the update information, and select ENTER to start reprogramming.
9. The control module update is now completed.
10. Do the PCM idle learn procedure (refer to the service information).
END
Page 7 of 7