A18-082
Service Bulletin Details
Public Details for: A18-082
Service bulletin - siriusxm radio does not work for subscribers after the 3-month trial period, and iphones cannot connect to apple carplay.
- 2018 -
Models from 2018
2018 HONDA FIT |
Service Bulletin 18-082 April 26, 2019 Version 2 ® SiriusXM Radio Stops Working for Subscribers After the Trial Period ™ and Apple CarPlay Will Not Launch Supersedes 18-082, dated August 10, 2018. See REVISION SUMMARY. AFFECTED VEHICLES Year Model Trim VIN Range 2018 Fit Sport, EX, EX-L, and EX-L With Navigation ALL REVISION SUMMARY This bulletin has been extensively revised. American Honda recommends that you read this entire bulletin thoroughly. SYMPTOM ® SiriusXM Radio does not work for subscribers after the 3-month trial period, and iPhones cannot connect to ™ Apple CarPlay . POSSIBLE CAUSE ™ The audio unit will not launch Apple CarPlay when an iPhone is connected to the USB port. CORRECTIVE ACTION Update the audio unit software. WARRANTY CLAIM INFORMATION The normal warranty applies. Operation Number Description Flat Rate Time Defect Code Symptom Code Template ID Failed Part Number 0525A3 Update the audio unit software. 0.3 hr 03214 03217 A18082A 39171-T5R-A21 Skill Level: Repair Technician CUSTOMER INFORMATION:The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an authorized Honda automobile dealer. © 2019 American Honda Motor Co., Inc. — All Rights Reserved Page 1 of 8 REPAIR PROCEDURE NOTES • Before updating the software, write down the customer's audio unit presets. • Connect a fully charged battery to the vehicle, and leave it connected during the entire procedure to maintain steady voltage. • Apply the parking brake to keep the headlights turned off during the update. 1. From your computer's desktop, open Honda Firmware Downloader. Refer to job aid: Honda Firmware Downloader for any additional information. Make sure the USB flash drive is empty and formatted to FAT 32. 2. Enter the VIN. This is important as the software can be different depending on the trim level. Enter the service bulletin number, then select the download icon when the correct software is found. NOTE The software download may take up to 10-15 minutes depending on the size of the file and the quality of your internet connection. 3. Once the download is complete, return to the vehicle. 4. Verify the software version. 4.1. From the home screen, press the Day/Night button, MENU icon, and VOL/Power/AUDIO knob in sequence and hold them for about 5 seconds. Page 2 of 8 4.2. Select Detail Information & Setting. 4.3. From the Detail Information & Setting screen, press and hold the MENU icon for 5 seconds until the display transfers to the Developer Diag screen. 4.4. From the Developer Diag screen, select Detail Version Info. Then, confirm the current TEGRA Build Version and SH Main Software Version. Refer to the tables below for current and new versions. Software Details Current Software Versions Models with Navigation Models without Navigation TEGRA Build Version 81.027.03.3.1025 81.027.03.3.1021 Touch Version T5AR04 T5AR04 Page 3 of 8 5. Once the software update is downloaded onto the USB flash drive, insert it into the USB port. 6. A screen will automatically appear with the prompt Would you like to update?. Make sure each software version of Tegra/Touch in the New section are correct. Select Yes to update the software. NOTE If the screen does not appear, the software may not have correctly downloaded onto the USB flash drive. Try to download the software again. Software Details New Software Versions Models with Navigation Models without Navigation TEGRA Build Version 85.028.00.3.1025 85.028.00.3.1021 Touch Version T5AR04 T5AR04 NOTE In case the USB flash drive gets unplugged, a USB memory device unplugged message will appear. Select OK to clear the screen, and connect the USB flash drive once again to continue the software update. 7. After selecting Yes, the unit will reboot and the version update will start. The screen below will display for about 30 minutes. Page 4 of 8 8. Once the update is complete, the unit will reboot again. Remove the USB drive tool from the port. 9. After the update is complete, the following screen will appear. To bypass this screen, press and hold the Day/Night button and Home icon. 10. Select OK. 11. Go to SOFTWARE UPDATE CONFIRMATION to confirm the software update. Page 5 of 8 SOFTWARE UPDATE CONFIRMATION PROCEDURE After the version update is complete, you must confirm that the software is up-to-date. 1. From the HOME screen, press the Day/Night button, MENU icon, and VOL/Power/AUDIO knob in sequence and hold them for about 5 seconds. 2. Select Detail Information & Setting. 3. From the Detail Information & Setting screen, press and hold the MENU icon for 5 seconds until the display changes to the Developer Diag screen. Page 6 of 8 4. From the Developer Diag screen, select Detail Version Info and confirm the TEGRA Build Version and SH Main Software Version. Software Details New Software Versions Models with Navigation Models without Navigation TEGRA Build Version 85.028.00.3.1025 85.028.00.3.1021 Touch Version T5AR04 T5AR04 Page 7 of 8 5. Insert the USB flash drive into the USB port to start the factory data reset (FDR) procedure. 6. A screen will automatically appear with the prompt Would you like to update?. Select FDR. NOTE The FDR takes about 3 minutes to complete. 7. After the FDR is complete, the following screen will appear. To bypass this screen, press and hold the Day/Night button and Home icon. 8. Select OK, and park the vehicle outside in an open area to acquire the GPS signal. 9. Once the procedure is complete, input the customer's audio unit presets, and have the service advisor tell the customer that any previously paired devices must be paired again. After informing the customer about the need for pairing, make sure to document it on the repair order. END Page 8 of 8