A9019172048926_7

90 Various messages displayed, DTCs B200FF1 and/or B200FF2 stored in the camera control module
90 19 17 2048926/7 June 5, 2019. Supersedes Technical Service Bulletin Group 90 number 18-07 dated
November 2, 2018 for reasons listed below.
Model(s)
Year
VIN Range
Vehicle-Specific Equipment
A4, Q7
2016 - 2019
All
With multifunction camera
A5, A5,
Cabriolet,
and Q5
2018 - 2019
All
With multifunction camera
Condition
REVISION HISTORY
Revision
Date
Purpose
7
-
Revised header (Changed model code)
Revised Warranty (Updated Labor Operations)
6
11/02/2018
Revised Warranty (Updated Labor Operations)
5
10/18/2018
Revised header data (Updated filter)
Revised Service (Updated SVM table)
Revised Warranty (Updated Labor Operations)
Customer statement:
In the driver information system (DIS) one or several of the following messages are displayed:
 Audi pre sense: malfunction.
 Traffic sign detection: malfunction.
 Adaptive cruise control with congestion assistant is not available.
 Audi active lane assist: currently not available.
Workshop findings:
One of the following DTC(s) is stored in the camera control module, R242 (address word 00A5) as either static or
sporadic:
 DTC B200FF1 (internal malfunction).
 DTC B200FF2 (internal malfunction).
Page 1 of 4
© 2019 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
Technical Background
During its start phase, the camera recognizes a malfunction in the internal communication.
Production Solution
Improved software addressed the condition (DTC B200FF2).
Service
1. If only DTC B200FF1 (internal malfunction) is logged, then replace the camera control module.
2. If both DTCs B200FF1 and B200FF2 are logged, then replace the camera control module.
3. If only DTC B200FF2 (internal malfunction) is logged, proceed as follows:
 Update the camera control module, R242 (address word 00A5) to SW0044 via SVM code A5A002.
Note:
Claims with a replaced camera control modules which only had the DTC B200FF2 once may be denied.
SVM Update Instructions
1. Follow all instructions in TSB 2011732: 00 Software Version Management (SVM), operating instructions.
2. Update the camera control module, R242 (address word 00A5) using the SVM action code as listed in the
table below, if necessary:
Model
Old Software Part
Number
Old Software
Version
New Software
Part Number
New
Software
Version
SVM Code
Input
(or higher)
A4/A5
8W0907217A
0030
8W0907217B
0042
8W0907217C
8W0907217B
0044
0050
8W0907217C
0052
*
4M0907217D
0044
A5A002
4M0907217B
Q7
4M0907217C
4M0907217D
Page 2 of 4
© 2019 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
4M0907217E
0050
4M0907217E
0052
80A907217
0042
80A907217
0044
80A907217A
0050
80A907217A
0052
Q5
Warranty
Claim Type:
 110 up to 48 Months/50,000 Miles.
 G10 for CPO Covered Vehicles – Verify Owner.
 If the vehicle is outside any warranty, this Technical Service Bulletin is informational
only.
Service Number:
9638
Damage Code:
0040
Labor Operations:
Software Update
0151 0000
Time stated on
the diagnostic
protocol (Max
70 TU)
Camera Driver Assist Sys Adjust
9638 1550
See SRT
Preparation Driver Assist Calibration
9092 0050
See SRT
Vehicle front + rear check
4495 0150
See SRT
Camera Driver Assist Sys replaced
Inside mirror remove and reinstall
9638 5550 (A4, A5, Q5,
and Q7)
9638 5500 (A5
Cabriolet)
6827 1900 (A4, A5, A5
Cabriolet, Q5, and Q7)
2 Headlight assembly adjust
9415 1650 (Q5 and Q7
only)
Or
Or
2 Headlight assembly adjust
9415 1651 (LED Only)
(Q5 and Q7 only)
See SRT
See SRT
See SRT
Page 3 of 4
© 2019 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
Diagnostic Time:
Claim Comment:
GFF
0150 0000
Time stated on
diagnostic
protocol (Max
100 TU)
Road test prior to the service procedure
No allowance
0 TU
Road test after the service procedure
0121 0004
10 TU
As per TSB #2048926/5
All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures
Manual. Claims are subject to review or audit by Audi Warranty.
Required Parts and Tools
Always check with your Parts Department and/or ETKA for the latest information and parts bulletins.
Part Number
Part Description
Quantity
See ETKA
Front Camera for driver assistance programs
01
4M0955609
Silicone pad for the front camera
01
See ETKA
Fasteners, Bolts, Nuts, and Screws as needed per
the Repair Manual
See ETKA/ELSA
Additional Information
The following Technical Service Bulletin will be necessary to complete this procedure:
 TSB 2011732, 00 Software Version Management (SVM), operating instructions.
All parts and service references provided in this TSB (2048926) are subject to change and/or removal.
©2019 Audi of America, Inc. All rights reserved. The information contained in this document is based on the
latest information available at the time of printing and is subject to the copyright and other intellectual property
rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes
at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites without the prior expressed written permission of the
publisher.
Page 4 of 4
© 2019 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.