B121519

Service Information
Page 1 of 2
Engine Electrical Systems
Technical Service
B12 15 19
May 2019
Please perform the procedure outlined in this Service Information on all affected vehicles before
customer delivery. In the event the customer has already taken delivery of the vehicle, please perform
the procedure the next time the vehicle is in the shop.
SERVICE ACTION: REPLACING THE ELECTRICAL MACHINE
ELECTRONICS (EME) - F15
MODEL
F15 PHEV (X5 xDrive40e)
AFFECTED VEHICLES
This Service Action involves F15 PHEV (X5 xDrive40e) produced from August 11, 2015 to March 14,
2018.
Vehicles which require this Service Action to be completed will show it as Open when checked either
in AIR, or the Service Menu of DCSnet (Dealer Communication System).
SITUATION
Production fault on a printed circuit board of the electrical machine electronics (EME).
In the event of an EME failure, a yellow check control message is displayed on the KOMBI; caused by
the shutdown of the high-voltage system. The combustion engine is started and driving is stil possible.
Note: The electric drive function may possibly be restored by switching the drive-readiness state off
and on again.
CORRECTION
Replace the electrical machine electronics (EME).
PROCEDURE
Replace the electrical machine electronics as per REP 12 36 610 – “Replacing electrical machine
electronics (EME)”.
Important warning for working on the high-voltage systems on the F15 PHEV:
Only properly trained personnel, who have passed all applicable technical training courses,
should perform any maintenance or repairs on any Hybrid or Electric Vehicle. Work performed
by unqualified persons may result in severe injury or damage to the vehicle. Additional
information is found in Repair Instruction 61 00… Observe safety instructions when handling
electric vehicles.
2
PARTS INFORMATION
Part Number
12 36 9 494 405
18 30 8 636 423
Description
Electrical motor electronics
Muffler Clamp (D=67.5mm)
1
1
Quantity
Description
BMW Antifreeze
Quantity
Sublet as needed
Bulk Materials
Part Number
82 14 1 467 704
Note: Other small parts such as screws, nuts and seals, which must also be replaced
according to the ISTA repair instructions must be selected from the Electronic Parts Catalogue
according to the respective vehicle type and invoiced under the special defect code.
WARRANTY INFORMATION
Refer to Attachment.
Attachment to SI B12 15 19
May 2019
SERVICE ACTION: REPLACING THE ELECTRICAL MACHINE
ELECTRONICS (EME) - F15
WARRANTY INFORMATION
Reimbursement for this Service Action repair campaign will be via normal claim entry utilizing the
following information:
Defect Code:
00 12 03 05 00
Completion before the first vehicle delivery to a customer or the vehicle is already in the
workshop.
Work Package # 1
Labor Operation:
00 67 547
Labor Allowance:
58 FRU
Description:
Replacing the electrical machine electronics (EME)
and programming and encoding control units
(includes connecting an approved battery
charger/power supply and performing a vehicle test)
(Plus work)
Labor Allowance:
50 FRU
Description:
Replace the electrical machine electronics (EME)
(Programming and encoding control units was
performed in conjunction with another campaign or
repair during the same workshop visit) (Plus work)
Or:
Work Package # 2
Labor Operation:
00 67 548
During the same workshop visit, if a vehicle also requires another Technical Campaign or repair that
also includes programming and encoding the control units, the programming procedure may only be
invoiced one time.
Or:
The vehicle arrives at your center and this Service Action shows open (No other Main work will
be performed/claimed during this workshop visit)
Work Package # 3
Labor Operation:
00 67 037
Labor Allowance:
60 FRU
Description:
Replacing the electrical machine electronics (EME)
and programming and encoding control units
(includes connecting an approved battery
charger/power supply and performing a vehicle test)
(Main work)
Claim Repair Comments
Unless additional related/in conjunction work was required, from the above information, only reference
the SIB number and the work package number performed in the RO technician notes and the claim
comments (For example: B12 15 19 WP 1).
1
And, as needed:
Sublet – Bulk Materials (With Claim Comment)
Sublet Code 4
Up to $15.00
Reimbursement for the repair-related bulk material (Do not use
the BMW part number for claim submission)
Sublet reimbursement calculation for claiming the applicable repair-related bulk material (BMW part
number) is at the dealer net price amount for the quantities used plus your center’s handling.
BMW Antifreeze/Coolant: Claim the corresponding dollar amount for the quantity needed to replace
what was drained with a 50/50 coolant/water solution.
Enter this material cost in sublet and itemize the amount on the repair order and in claim comment
section.
Programming and Encoding - Vehicle Control Units (Consequential with Claim Comments)
A. The programming procedure automatically reprograms and encodes all vehicle control modules
which do not have the latest software i-level. If one or more control module failures occur during
this programming procedure:

Please claim this consequential control module-related repair work under the defect code listed
in this bulletin with the applicable AIR labor operations.
Please explain this additional work (The why and what) on the repair order and in the claim comments
section.
B. For control module failures that occurred prior to performing this programming procedure:

When covered under an applicable limited warranty, claim this control module-related repair
work using the applicable defect code and labor operations (including diagnosis) in AIR.
And, as applicable:
Alternative Mobility Solution (AMS) for Vehicle Owners (With Claim Comment)
This Service Action repair qualifies for Alternative Mobility Solution (AMS) expense reimbursement,
claim this item under the Defect Code noted above as follows:

Sublet Code 2 - Itemize the AMS sublet amount on the repair order and in the claim comment
section.
Please refer to SI B01 29 16 for additional information.
2