19TechReferncDoc

2019
Pre-Delivery Inspection
Technician Reference Document
Effective 7-11-2019-US
Version 1.8
Table of Contents
Technician Reference Document
Technician Reference Document Overview
The Pre-Delivery Inspection Technician Reference Document is designed to be a resource used in hand with
the Pre-Delivery Inspection Checklist (PDI). The PDI Checklist has been simplified to make the process more
efficient, and in doing so, this document has been created to be used as a reference for checklist items that
may have additional information. On the PDI Checklist, you find that certain items have been notated with an
asterisk symbol (*), this lets you know that additional information can be found in this Technician Reference
Document.
Below you will find a list of each model, with the page numbers to their left. After navigating to the desired
page, you will notice each model page is formatted similarly to the PDI Checklists. After each section title is the
original checklist item, followed by any additional information specific to that model.
Table of Contents
3-4
A3 Sedan & Cabriolet/S3/RS 3
5-6
A4/S4/A4 allroad
7-8
A5/S5/RS 5
9-11
A6
12-14
A7
15-16
A8 L
17-18
e-tron
19-20
Q3
21-22
Q5/SQ5
23-24
Q7
25-26
Q8
27-28
TT/TTS/TTRS
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 2
A3 Sedan & Cabriolet/S3/RS 3
Technician Reference Document
Vehicle Preparation
Trunk Inspection
•      Set adaption channel to enable CD Ripping using Guided
Functions (if equipped with NAV)
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Set adaptation channel (via Special functions > Service work
> 5F-Activating/deactivating storage of music). Also referred
to as CD Ripping. Perform 3 button reset of the MMI to
complete the activation. Refer to the owner’s manual for
model-specific button sequence
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Perform diagnostic work
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Verify temporary inflatable spare tire is present (A3 Sedan,
S3, and A3 Cabriolet FWD only)
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
Connect vehicle diagnostic tester
•      Select “Diagnosis” mode and start diagnosis
Interior
•      Perform vehicle identification
•      Check operation of window, lock, and seat controls
•      Untick “Working with Guided Fault Finding”
•      Switch to “Special functions” tab and select following
program:
Delivery Inspection total
•      Start program by selecting “Carry out check”
•      Continue to follow instructions on screen and complete
the process
•      Switch to the “Control units” tab, press the “Guided Fault
Finding” button and launch Guided Fault Finding as far
as the test plan
•      The static event memory entries must be evaluated and,
if necessary, processed using Guided Fault Finding
•      Exit diagnosis; diagnostic log for delivery inspection is
sent automatically
Exterior
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
•      Check rear view mirror operation
Check self-dimming function/lighting
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation (Sedan
only)
Verify open/close/vent/deflector at edge and sunshade
operation
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
Lighting and Windshield
•      Test windshield washers (and headlight washers on S3 and
RS 3)
Headlights must be on to test functionality of the headlight
washers
Settings
•      Set time source setting to “GPS” (if equipped) and set auto
daylight savings time to “on”*
Change time zone appropriate to dealer location
•      Verify and set language and measurement units
This can be changed in the Settings menu by going to Menu >
Vehicle > Vehicle settings
•      Verify Speech Dialog System is operating (if equipped)
Press the “Talk” button and verify several commands
•      Set “Entertain. Fad.” in Parking aid to an audible level (if
equipped)
Via “Menu > Vehicle > Left Option > Driver Assistance >
Parking Aid”
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 3
A3 Sedan & Cabriolet/S3/RS 3
Technician Reference Document
Settings (continued)
Driving Performance (continued)
•      Set dealership location in navigation (if equipped)
•      Verify engine performance and acceleration
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning
This can be changed in the Driver Assistance Settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual > Select OffMedia / Radio / SAT
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect® (USA ONLY) (if equipped)
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
•      Verify operation of Audi parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
•      Turn on the Wi-Fi® hotspot (if equipped)
Ensure the wireless network is turned on (Telephone > Right
Option > Wi-Fi® options > Wi-Fi® “On”)
•      Check Wi-Fi® hotspot visibility. No data available at PDI (if
equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Enable Google Earth view for navigation (if equipped)
Enable Google Earth view in the Navigation > Map Settings
and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol.
Cabriolet Functionality
•      Test operation of power folding top
Perform with engine running to conserve battery power
Post-Road Test Inspection
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Driving Performance
•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 4
A4/S4/A4 allroad
Technician Reference Document
Vehicle Preparation
Trunk Inspection (continued)
•      Set adaption channel to enable CD Ripping using Guided
Functions (if equipped with NAV)
•      Check battery clamps for proper torque
Set adaptation channel (via Special functions > Service work
> 5F-Activating/deactivating storage of music). Also referred
to as CD Ripping. Perform 3 button reset of the MMI to
complete the activation. Refer to the owner’s manual for
model-specific button sequence
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Perform diagnostic work
Connect vehicle diagnostic tester
•      Select “Diagnosis” mode and start diagnosis
•      Perform vehicle identification
•      Untick “Working with Guided Fault Finding”
•      Switch to “Special functions” tab and select following
program:
Delivery Inspection Total
•      Start program by selecting “Carry out check”
•      Continue to follow instructions on screen and complete
the process
Refer to Elsa Pro for specification
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating
•      Check rear view mirror operation
Check self-dimming function/lighting
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
•      Switch to the “Control units” tab, press the “Guided Fault
Finding” button and launch Guided Fault Finding as far
as the test plan
Settings
•      The static event memory entries must be evaluated and,
if necessary, processed using Guided Fault Finding
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
•      Exit diagnosis; diagnostic log for delivery inspection is
sent automatically
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Set spare tire pressure
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Effective 7-11-2019-US
Version 1.8
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Settings menu by going to Menu >
Vehicle > Vehicle settings
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands
•      Set “Entertain. Fad.” in Parking aid to an audible level
Via “Menu > Vehicle > Left Option > Driver Assistance > Parking Aid”
•      Set “Music volume while parking” to medium
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
Model Year 2019 | Audi Pre-Delivery Reference Document | 5
A4/S4/A4 allroad
Technician Reference Document
Settings (continued)
Driving Performance (continued)
•      Turn off Manual Speed Warning (if equipped)
•      Test drive vehicle applying brakes several times
This can be changed in the Driver Assistance settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual > Select Off
Media / Radio / SAT
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Driver Assistance
•      Verify operation of parking system (if equipped)
Audi connect® (USA ONLY) (if equipped)
•      Turn on the Wi-Fi® hotspot (if equipped)
Ensure the wireless network is turned on (Telephone > Right
Option > Wi-Fi® options > Wi-Fi® “On”)
•      Check Wi-Fi® hotspot visibility. No data available at PDI (if
equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Enable Google Earth view for navigation (if equipped)
Enable Google Earth view in the Navigation > Map Settings
and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol.
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
•      Verify all vehicle Head-up display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-up display (as
equipped)
Post-Road Test Inspection
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Driving Performance
•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 6
A5/S5/RS 5
Technician Reference Document
Vehicle Preparation
Trunk Inspection
•      Set adaption channel to enable CD Ripping using Guided
Functions (if equipped with NAV)
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Set adaptation channel (via Special functions > Service work
> 5F-Activating/deactivating storage of music). Also referred
to as CD Ripping. Perform 3 button reset of the MMI to
complete the activation. Refer to the owner’s manual for
model-specific button sequence
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Perform diagnostic work
Connect vehicle diagnostic tester
•      Select “Diagnosis” mode and start diagnosis
•      Perform vehicle identification
•      Untick “Working with Guided Fault Finding”
•      Switch to “Special functions” tab and select following
program:
Delivery Inspection total
•      Start program by selecting “Carry out check”
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Set spare tire pressure
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Continue to follow instructions on screen and complete
the process
•      Verify proper operation of climate control
•      Switch to the “Control units” tab, press the “Guided Fault
Finding” button and launch Guided Fault Finding as far
as the test plan
•      Inspect operation of all power outlets
•      The static event memory entries must be evaluated and,
if necessary, processed using Guided Fault Finding
•      Exit diagnosis; diagnostic log for delivery inspection is
sent automatically
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
Ensure proper heating and A/C cooling and open all panel
vents
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Setup/Settings menu
Lighting and Windshield
•        Test windshield washers (and headlight washers - RS 5
only)
Headlights must be on to test functionality of the headlight
washers
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands
•      Set “Entertain. Fad.” in Parking aid to an audible level
Via Menu > Vehicle > Driver Assistance > Parking Aid
•      Set “Music volume while parking” to medium
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 7
A5/S5/RS 5
Technician Reference Document
Settings (continued)
Driving Performance (continued)
•      Set dealership location in navigation (if equipped)
•      Verify engine performance and acceleration
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning (if equipped)
This can be changed in the Driver Assistance settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual->Select Off
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect® (USA ONLY) (if equipped)
•      Turn on the Wi-Fi® hotspot (if equipped)
Ensure the wireless network is turned on (Telephone > Right
Option > Wi-Fi® options > Wi-Fi® “On”)
•      Check Wi-Fi® hotspot visibility. No data available at PDI (if
equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Enable Google Earth view for navigation (if equipped)
Enable Google Earth view in the Navigation > Map Settings
and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol.
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
•      Verify operation of parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
•      Verify all vehicle Head-up display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
Convertible Functionality (if equipped)
•      Test operation of power folding top
Perform with engine running to conserve battery power
On-Hoist Inspection
Post-Road Test Inspection
•      Install wheel bolt covers and center caps as supplied
•      Check engine oil level
Wheel bolt covers and center caps can be found in the PDI kit
•      Inspect wheel bolts for proper torque
Fill oil to the max level when the vehicle is at operating temperature
Use torque wrench to verify
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Driving Performance
•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 8
A6
Technician Reference Document
Vehicle Preparation
Trunk Inspection (continued)
•      Perform any open campaigns
•      Set spare tire pressure
Follow instructions listed in campaign documentation
•      Perform diagnostic work
Connect vehicle diagnostic tester
•      Select “Diagnosis” mode and start diagnosis
•      Perform vehicle identification
•      Untick “Working with Guided Fault Finding”
•      Switch to “Special functions” tab and select following
program:
Delivery Inspection total
•      Start program by selecting “Carry out check”
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
•      Place one PR Number Label in the Warranty and
Maintenance Book inside front cover and one on the Rear
Panel Sill Frame under the luggage compartment floor, if
not already there
For vehicles produced prior to September 12, 2018
Labels are located in the trunk on top of spare tire
Rear Panel Sill Frame location: Top Arrow
•      Continue to follow instructions on screen and complete
the process
•      Switch to the “Control units” tab, press the “Guided Fault
Finding” button and launch Guided Fault Finding as far
as the test plan
•      The static event memory entries must be evaluated and,
if necessary, processed using Guided Fault Finding
•      Exit diagnosis; diagnostic log for delivery inspection is
sent automatically
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
•      Check all doors for proper power closing (if equipped)
For vehicles equipped with the power door closing feature,
check all doors for proper closing
Lighting and Windshield
•      Test windshield washers (and headlight washers if
equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 9
A6
Technician Reference Document
Trunk Inspection (continued)
Settings
Warranty and Maintenance inside cover placement
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on”
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Setup/Settings menu
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands
•      Set “Music volume while parking” to medium
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Set dealership location in navigation
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning (if equipped)
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features
This can be changed in the Driver Assistance Settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual > Select Off
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Verify operation of heated/ventilated and massaging seats
(if equipped)
Check both front and rear. Massaging feature is in the front
seats only (if equipped)
•      Verify proper operation of climate control*
Ensure proper heating and A/C cooling, open all panel vents
for all zones
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Audi connect® (USA ONLY) (if equipped)
•      Turn on the Wi-Fi® hotspot (if equipped)
Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” )
•      Check Wi-Fi® hotspot visibility. No data available at PDI
due to dealer demo mode (if equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX
is the last four digits of the VIN. Via Telephone > Options >
Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings
> Access point (SSID)
•      Enable satellite map for navigation (if equipped)
Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom
right-hand corner of the Navigation map screen.
On-Hoist Inspection
•      Remove locking elements on front axle suspension struts
(For vehicles with sport suspension 1BE)
Push all five locking elements on each suspension strut off
piston rod. Refer to Elsa for full procedure
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 10
A6
Technician Reference Document
On-Hoist Inspection (continued)
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers can be found in the PDI kit
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Driving Performance
•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
•      Verify operation of parking system
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
•      Verify all vehicle Head-up Display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
Post-Road Test Inspection
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 11
A7
Technician Reference Document
Vehicle Preparation
Trunk Inspection (continued)
•      Perform any open campaigns
•      Set spare tire pressure
Follow instructions listed in campaign documentation
•      Perform diagnostic work
Connect vehicle diagnostic tester
•      Select “Diagnosis” mode and start diagnosis
•      Perform vehicle identification
•      Untick “Working with Guided Fault Finding”
•      Switch to “Special functions” tab and select following
program:
Delivery Inspection total
•      Start program by selecting “Carry out check”
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
•      Place one PR Number Label in the Warranty and
Maintenance Book inside front cover and one on the Rear
Panel Sill Frame under the luggage compartment floor, if
not already there
For vehicles produced prior to September 12, 2018
Labels are located in the trunk on top of spare tire
Rear Panel Sill Frame location: Top Arrow
•      Continue to follow instructions on screen and complete
the process
•      Switch to the “Control units” tab, press the “Guided Fault
Finding” button and launch Guided Fault Finding as far
as the test plan
•      The static event memory entries must be evaluated and,
if necessary, processed using Guided Fault Finding
•      Exit diagnosis; diagnostic log for delivery inspection is
sent automatically
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
•      Check all doors for proper power closing (if equipped)
For vehicles equipped with the power door closing feature,
check all doors for proper closing
Lighting and Windshield
•      Test windshield washers (and headlight washers if
equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 12
A7
Technician Reference Document
Trunk Inspection (continued)
Settings
Warranty and Maintenance inside cover placement
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on”
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Setup/Settings menu
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands
•      Set “Music volume while parking” to medium
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Set dealership location in navigation
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning (if equipped)
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Verify operation of heated/ventilated and massaging seats
(if equipped)
Check both front and rear. Massaging feature is in the front
seats only (if equipped)
•      Verify proper operation of climate control*
Ensure proper heating and A/C cooling, open all panel vents
for all zones
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
This can be changed in the Driver Assistance Settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual > Select Off
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect® (USA ONLY) (if equipped)
•      Turn on the Wi-Fi® hotspot (if equipped)
Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” )
•      Check Wi-Fi® hotspot visibility. No data available at PDI
due to dealer demo mode (if equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX
is the last four digits of the VIN. Via Telephone > Options >
Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings
> Access point (SSID)
•      Enable satellite map for navigation (if equipped)
Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom
right-hand corner of the Navigation map screen.
On-Hoist Inspection
•      Remove locking elements on front axle suspension struts
(For vehicles with sport suspension 1BE)
Push all five locking elements on each suspension strut off
piston rod. Refer to Elsa for full procedure
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 13
A7
Technician Reference Document
On-Hoist Inspection (continued)
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers can be found in the PDI kit
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load
Condition. See separate “2019 Normal Load Condition Tire
Pressure Table” posted on ServiceNet. If going to stock,
set to maximum recommended tire pressures listed on the
B-pillar door jamb, and store tire pressure values in Car/System menu
Driving Performance
•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
•      Verify operation of parking system
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
•      Verify all vehicle Head-up display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
Post-Road Test Inspection
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating
temperature
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 14
A8 L
Technician Reference Document
Vehicle Preparation
Trunk Inspection (continued)
•      Perform any open campaigns
•      Set spare tire pressure
Follow instructions listed in campaign documentation
•      Perform diagnostic work
Connect vehicle diagnostic tester
•      Select “Diagnosis” mode and start diagnosis
•      Perform vehicle identification
•      Untick “Working with Guided Fault Finding”
•      Switch to “Special functions” tab and select following
program:
Delivery Inspection total
•      Start program by selecting “Carry out check”
•      Continue to follow instructions on screen and complete
the process
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Switch to the “Control units” tab, press the “Guided Fault
Finding” button and launch Guided Fault Finding as far
as the test plan
•      Verify operation of heated/ventilated and massaging seats
(if equipped)
•      The static event memory entries must be evaluated and,
if necessary, processed using Guided Fault Finding
Check both front and rear. Massaging feature is in the front
seats only (if equipped)
•      Exit diagnosis; diagnostic log for delivery inspection is
sent automatically
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
•      Check all doors for proper power closing
For vehicles equipped with the power door closing feature,
check all doors for proper closing
Lighting and Windshield
•      Test windshield washers (and headlight washers if
equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
Effective 7-11-2019-US
Version 1.8
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling, open all panel vents
for all zones
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on”
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Setup/Settings menu
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands
•      Set “Music volume while parking” to medium
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
Model Year 2019 | Audi Pre-Delivery Reference Document | 15
A8 L
Technician Reference Document
Settings (continued)
Driving Performance (continued)
•      Turn off Manual Speed Warning (if equipped)
•      Verify engine performance and acceleration
This can be changed in the Driver Assistance Settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual > Select Off
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Audi connect® (USA ONLY)
Driver Assistance
•      Turn on the Wi-Fi® hotspot (if equipped)
•      Verify operation of parking system
Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” )
•      Check Wi-Fi® hotspot visibility. No data available at PDI
due to dealer demo mode (if equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX
is the last four digits of the VIN. Via Telephone > Options >
Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings
> Access point (SSID)
•      Enable satellite map for navigation (if equipped)
Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom
right-hand corner of the Navigation map screen.
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
•      Verify all vehicle Head-up display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
Post-Road Test Inspection
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
On-Hoist Inspection
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers can be found in the PDI kit
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Driving Performance
•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 16
e-tron
Technician Reference Document
Vehicle Preparation
Trunk Inspection
•      Perform any open campaigns
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Follow instructions listed in campaign documentation
•      Perform diagnostic work
Connect vehicle diagnostic tester
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Select “Diagnosis” mode and start diagnosis
Interior
•      Perform vehicle identification
•      Check operation of window, lock, and seat controls
•      Untick “Working with Guided Fault Finding”
•      Switch to “Special functions” tab and select following
program:
Delivery Inspection total
•      Start program by selecting “Carry out check”
•      Continue to follow instructions on screen and complete
the process
•      Switch to the “Control units” tab, press the “Guided Fault
Finding” button and launch Guided Fault Finding as far
as the test plan
•      The static event memory entries must be evaluated and,
if necessary, processed using Guided Fault Finding (exception: for address 0051 and 00CE the DTC: U111500:
Component protection No basic setting for SHE key –
needs to be ignored, cannot be deleted)
•      Exit diagnosis; diagnostic log for delivery inspection is
sent automatically
Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Verify operation of heated/ventilated and massaging seats
(front/rear) (if equipped)
Check both front and rear. Massaging feature is in the front
seats only (if equipped)
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling, open all panel vents
for all zones
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
•      Check all doors for proper power closing
For vehicles equipped with the power door closing feature,
check all doors for proper closing
Lighting and Windshield
•      Test windshield washers (and headlight washers if
equipped)
Headlights must be on to test functionality of the headlight
washers
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on”
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Setup/Settings menu:
Home > Settings > General > Measurement Units >
Consumption (electric motor) to mi/kWh, and check to ensure all other units are set to US specs
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands
•      Set “Music volume while parking” to medium
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 17
e-tron
Technician Reference Document
Settings (continued)
On-Hoist Inspection (continued)
•      Set dealership location in navigation (if equipped)
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning (if equipped)
This can be changed in the Driver Assistance Settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual > Select Off
•      Disable climate control via door unlock
Main screen => Vehicle => Climate control => select small
temperature gauge symbol in upper right section => settings
(“wheel” upper right) => unselect (disable) “Start A/C after
unlocking”. Check and adjust, if needed. Button position
“off”, in left position.
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Driving Performance
•      Verify electric motor performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Audi connect® (USA ONLY) (if equipped)
Driver Assistance
•      Turn on the Wi-Fi hotspot (if equipped)
•      Verify operation of parking system
®
Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” )
•      Check Wi-Fi® hotspot visibility. No data available at PDI
due to dealer demo mode (if equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX
is the last four digits of the VIN. Via Telephone > Options >
Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings
> Access point (SSID)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
•      Verify all vehicle Head-up display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
•      Enable satellite map for navigation (if equipped)
Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom
right-hand corner of the Navigation map screen.
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers can be found in the PDI kit
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 18
Q3
Technician Reference Document
Vehicle Preparation
Trunk Inspection (continued)
•      Perform any open campaigns
•      Install wheel bolt cover removal tool from PDI kit into
trunk lid tool kit
Follow instructions listed in campaign documentation
•      Perform diagnostic work
Connect vehicle diagnostic tester
•      Select “Diagnosis” mode and start diagnosis
•      Perform vehicle identification
•      Untick “Working with Guided Fault Finding”
•      Switch to “Special functions” tab and select following
program:
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit to the right of the
spare tire
•      Set spare tire pressure
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
Delivery Inspection total
•      Start program by selecting “Carry out check”
Interior
•      Continue to follow instructions on screen and complete
the process
•      Check operation of window, lock, and seat controls
•      Switch to the “Control units” tab, press the “Guided Fault
Finding” button and launch Guided Fault Finding as far
as the test plan
•      The static event memory entries must be evaluated and,
if necessary, processed using Guided Fault Finding
•      Exit diagnosis; diagnostic log for delivery inspection is
sent automatically
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Lighting and Windshield
•      Test windshield washers (and headlight washers if
equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
•      Verify power tailgate is operational and set default opening
height
Adjust the trunk lid opening height to 77.7 inches (197 cm)
from the ground to the close button in the rear lid. Press and
hold the close button in the rear lid for at least four seconds
to program the opening height
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.” (if equipped with navigation)
Change time zone appropriate to the dealer location
•      Set “Entertain. Fad.” in Parking aid to an audible level (if
equipped)
Via “ Menu > Vehicle > Left Option > Drive Assistance > Parking Aid”
•      Verify and set language and measurement units
This can be changed in the Setup/Settings menu
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 19
Q3
Technician Reference Document
Settings (continued)
Driving Performance (continued)
•      Set dealership location in navigation (if equipped)
•      Verify engine performance and acceleration
Set dealership location for following back to dealership
during road test
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Audi connect® (USA ONLY) (if equipped)
•      Turn on the Wi-Fi® hotspot (if equipped)
Ensure the wireless network is turned on (Telephone > Right
Option > Wi-Fi® options > Wi-Fi® “On”)
•      Check Wi-Fi® hotspot visibility. No data available at PDI (if
equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Enable satellite map for navigation (if equipped)
Enable Google Earth view in the Navigation > Map Settings
and verify the white Google logo appears in the bottom
right-hand corner of the MMI screen next to the LTE symbol.
On-Hoist Inspection
Driver Assistance
•      Verify operation of parking system plus with rear cross
traffic assist (if equipped)
Verify operation of Audi parking system sensors with rear
view camera
Post-Road Test Inspection
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
On-Hoist Inspection
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Set and store tire pressures for either sold vehicle OR
stock inventory vehicle. See separate “2019 Normal Load
Condition Tire Pressure Table” posted on ServiceNet
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Driving Performance
•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 20
Q5/SQ5
Technician Reference Document
Vehicle Preparation
•      Set adaption channel to enable CD Ripping using Guided
Functions (if equipped with NAV)
Set adaptation channel (via Special functions > Service work
> 5F-Activating/deactivating storage of music). Also referred
to as CD Ripping. Perform 3 button reset of the MMI to
complete the activation. Refer to the owner’s manual for
model-specific button sequence
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Perform diagnostic work
Connect vehicle diagnostic tester
Exterior (continued)
the torque wrench key code from the base carrier bar box.
Insert the paper with the key code into the owner’s literature
wallet. Record torque wrench key code in the VDF to ensure
it’s documented in the event the paper with the code is
misplaced
Lighting and Windshield
•      Test windshield washers (and headlight washers if
equipped)
Headlights must be on to test functionality of the headlight
washers
•      Select “Diagnosis” mode and start diagnosis
Trunk Inspection
•      Perform vehicle identification
•      Verify power tailgate is operational and set default opening
height
•      Untick “Working with Guided Fault Finding”
•      Switch to “Special functions” tab and select following
program:
Delivery Inspection total
•      Start program by selecting “Carry out check”
•      Continue to follow instructions on screen and complete
the process
•      Switch to the “Control units” tab, press the “Guided Fault
Finding” button and launch Guided Fault Finding as far
as the test plan
•      The static event memory entries must be evaluated and,
if necessary, processed using Guided Fault Finding
•      Exit diagnosis; diagnostic log for delivery inspection is
sent automatically
Adjust the trunk lid opening height to 77.7 inches (197 cm)
from the ground to the close button in the rear lid. Press and
hold the close button in the rear lid for at least four seconds
to program the opening height
•      Install wheel bolt cover removal tool from PDI kit into
trunk lid toolkit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit to the right of the
spare tire
•      Set spare tire pressure
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
Exterior
Interior
•      Check all key buttons and features
•      Check operation of window, lock, and seat controls
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
•      Check all doors for proper power closing (if equipped)
For vehicles equipped with the power door closing feature,
check all doors for proper closing
•      Prepare the base bars for customer delivery (install bars
only upon customer request)
Install the rubber strips to the top of the base carrier bars
(do not install the carrier bars on the vehicle unless customer
has requested). Repackage the bars into the box if they are
not being installed on the vehicle. Retrieve the paper with
Effective 7-11-2019-US
Version 1.8
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
Model Year 2019 | Audi Pre-Delivery Reference Document | 21
Q5/SQ5
Technician Reference Document
Interior (continued)
On-Hoist Inspection
•      Check panoramic sunroof and sunshade operation (if
equipped)
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Setup/Settings menu
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands
•      Set “Entertain. Fad.” in Parking aid to an audible level
Via “ Menu > Vehicle > Left Option > Drive Assistance > Parking Aid”
•      Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Set and store tire pressures for either sold vehicle OR
stock inventory vehicle (See separate “2019 Normal Load
Condition Tire Pressure Table” posted on ServiceNet)
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Driving Performance
•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
•      Test drive vehicle applying brakes several times
•      Turn off Manual Speed Warning (if equipped)
This can be changed in the Driver Assistance settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual->Select Off
•      Calibrate rear view mirror
Media / Radio / SAT
Driver Assistance
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
•      Verify operation of parking system (if equipped)
Audi connect® (USA ONLY) (if equipped)
•      Verify all vehicle Head-up display functionality (if
equipped)
•      Turn on the Wi-Fi® hotspot (if equipped)
Ensure the wireless network is turned on (Telephone > Right
Option > Wi-Fi® options > Wi-Fi® “On”)
•      Check Wi-Fi® hotspot visibility. No data available at PDI (if
equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Enable Google Earth view for navigation (if equipped)
Enable Google Earth view in the Navigation > Map Settings
and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol.
Effective 7-11-2019-US
Version 1.8
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
Post-Road Test Inspection
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Model Year 2019 | Audi Pre-Delivery Reference Document | 22
Q7
Technician Reference Document
Vehicle Preparation
Trunk Inspection
•      Set adaption channel to enable CD Ripping using Guided
Functions (if equipped with NAV)
•      Verify power tailgate is operational and set to maximum
opening height (if equipped)
Set adaptation channel (via Special functions > Service work
> 5F-Activating/deactivating storage of music). Also referred
to as CD Ripping. Perform 3 button reset of the MMI to
complete the activation. Refer to the owner’s manual for
model-specific button sequence
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Perform diagnostic work
Connect vehicle diagnostic tester
•      Select “Diagnosis” mode and start diagnosis
•      Perform vehicle identification
•      Untick “Working with Guided Fault Finding”
•      Switch to “Special functions” tab and select following
program:
Delivery Inspection total
•      Start program by selecting “Carry out check”
•      Continue to follow instructions on screen and complete
the process
•      Switch to the “Control units” tab, press the “Guided Fault
Finding” button and launch Guided Fault Finding as far
as the test plan
•      The static event memory entries must be evaluated and,
if necessary, processed using Guided Fault Finding
•      Exit diagnosis; diagnostic log for delivery inspection is
sent automatically
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
•      Check all doors for proper power closing (if equipped)
For vehicles equipped with the power door closing feature,
check all doors for proper closing
Lighting and Windshield
•      Test windshield washers (and headlight washers if
equipped)
Headlights must be on to test functionality of the headlight
washers
Effective 7-11-2019-US
Version 1.8
Press and hold the close button in the rear lid for at least
four seconds to program the opening height. Verify operation
of handsfree release (if equipped)
•      Install wheel bolt cover removal tool from PDI kit into
trunk lid toolkit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit to the right of the
spare tire
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) and child safety features
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Verify operation of heated/ventilated and massaging seats
(if equipped)
Check both front and rear. Massaging feature is in the front
seats only (if equipped)
•      Verify operation of manual folding 2nd row and power
folding 3rd row seats
Controls for the power folding 3rd row are located in the
trunk
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Verify and set language and measurement units
This can be changed in the Setup/Settings menu
Model Year 2019 | Audi Pre-Delivery Reference Document | 23
Q7
Technician Reference Document
Settings (continued)
On-Hoist Inspection (continued)
•      Verify Speech Dialog System is operating
•      Set and store tire pressures for either sold vehicle OR
stock inventory vehicle (See separate “2019 Normal Load
Condition Tire Pressure Table” posted on ServiceNet)
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Press the “Talk” button and verify several commands
•      Set “Entertain. Fad.” in Parking aid to an audible level
Via “ Menu > Vehicle > Left Option > Drive Assistance > Parking Aid”
•      Set “Music volume while parking” to medium
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning (if equipped)
This can be changed in the Driver Assistance settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual >Select Off
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect® (USA ONLY) (if equipped)
•      Turn on the Wi-Fi® hotspot (if equipped)
Ensure the wireless network is turned on (Telephone > Right
Option > Wi-Fi® options > Wi-Fi® “On”)
•      Check Wi-Fi® hotspot visibility. No data available at PDI (if
equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Enable Google Earth view for navigation (if equipped)
Enable Google Earth view in the Navigation > Map Settings
and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol
On-Hoist Inspection
Driving Performance
•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
•      Verify operation of parking system
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
•      Verify all vehicle Head-up display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
Post-Road Test Inspection
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 24
Q8
Technician Reference Document
Vehicle Preparation
Trunk Inspection (continued)
•      Perform any open campaigns
•      Install wheel bolt cover removal tool from PDI kit into
trunk lid toolkit
Follow instructions listed in campaign documentation
•      Perform diagnostic work
Connect vehicle diagnostic tester
•      Select “Diagnosis” mode and start diagnosis
•      Perform vehicle identification
•      Untick “Working with Guided Fault Finding”
•      Switch to “Special functions” tab and select following
program:
Delivery Inspection total
•      Start program by selecting “Carry out check”
•      Continue to follow instructions on screen and complete
the process
•      Switch to the “Control units” tab, press the “Guided Fault
Finding” button and launch Guided Fault Finding as far
as the test plan
•      The static event memory entries must be evaluated and,
if necessary, processed using Guided Fault Finding
•      Exit diagnosis; diagnostic log for delivery inspection is
sent automatically
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
•      Check all doors for proper power closing (if equipped)
For vehicles equipped with the power door closing feature,
check all doors for proper closing
Lighting and Windshield
•      Test windshield washers (and headlight washers if
equipped)
Headlights must be on to test functionality of the headlight
washers
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit to the right of the
spare tire
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
•      Set spare tire pressure
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) and child safety features
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Verify operation of heated/ventilated and massaging seats
(if equipped)
Check both front and rear. Massaging feature is in the front
seats only (if equipped)
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
Trunk Inspection
•      Verify and set language and measurement units
•      Verify power tailgate is operational and set to maximum
opening height (if equipped)
•      Verify Speech Dialog System is operating
Press and hold the close button in the rear lid for at least
four seconds to program the opening height. Verify operation
of handsfree release (if equipped)
Effective 7-11-2019-US
Version 1.8
This can be changed in the Setup/Settings menu
Press the “Talk” button and verify several commands
Model Year 2019 | Audi Pre-Delivery Reference Document | 25
Q8
Technician Reference Document
Settings (continued)
Driving Performance
•      Set “Music volume while parking” to medium
•      Verify engine Start-Stop System functionality
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Set dealership location in navigation
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning (if equipped)
This can be changed in the Driver Assistance settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual >Select Off
Media / Radio / SAT
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect® (USA ONLY) (if equipped)
•      Turn on the Wi-Fi® hotspot (if equipped)
Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” )
•      Check Wi-Fi® hotspot visibility. No data available at PDI
due to dealer demo mode (if equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX
is the last four digits of the VIN. Via Telephone > Options >
Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings
> Access point (SSID)
•      Enable satellite map for navigation (if equipped)
Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom
right-hand corner of the Navigation map screen.
Driver Assistance
•      Verify operation of parking system
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
•      Verify all vehicle Head-up display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
Post-Road Test Inspection
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
On-Hoist Inspection
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Set and store tire pressures for either sold vehicle OR
stock inventory vehicle (See separate “2019 Normal Load
Condition Tire Pressure Table” posted on ServiceNet)
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 26
TT Coupe & Roadster/TTS/TT RS
Technician Reference Document
Vehicle Preparation
Trunk Inspection (continued)
•      Set adaption channel to enable CD Ripping using Guided
Functions (if equipped with NAV)
•      Check battery clamps for proper torque
Set adaptation channel (via Special functions > Service work
> 5F-Activating/deactivating storage of music). Also referred
to as CD Ripping. Perform 3 button reset of the MMI to
complete the activation. Refer to the owner’s manual for
model-specific button sequence
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Perform diagnostic work
Connect vehicle diagnostic tester
•      Select “Diagnosis” mode and start diagnosis
•      Perform vehicle identification
•      Untick “Working with Guided Fault Finding”
•      Switch to “Special functions” tab and select following
program:
Delivery Inspection total
•      Start program by selecting “Carry out check”
•      Continue to follow instructions on screen and complete
the process
•      Switch to the “Control units” tab, press the “Guided Fault
Finding” button and launch Guided Fault Finding as far
as the test plan
•      The static event memory entries must be evaluated and,
if necessary, processed using Guided Fault Finding
•      Exit diagnosis; diagnostic log for delivery inspection is
sent automatically
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Set spare tire pressure (NA for TT RS)
See separate “2019 Normal Load Condition Tire Pressure
Table” posted on ServiceNet under Pre-Delivery Inspection
Effective 7-11-2019-US
Version 1.8
Refer to Elsa Pro for specification
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Settings menu by going to Menu >
Vehicle > Vehicle settings
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands
•      Set “Entertain. Fad.” in Parking aid to an audible level
Via “Menu > Vehicle > Left Option > Driver Assistance > Parking Aid”
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning (if equipped)
This can be changed in the Driver Assistance settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual->Select Off
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Model Year 2019 | Audi Pre-Delivery Reference Document | 27
TT Coupe & Roadster/TTS/TT RS
Technician Reference Document
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
door jamb, and store tire pressure values in Car/System menu
Driving Performance
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/vibration/pulsation
Driver Assistance
•      Verify operation of Audi parking system plus (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Roadster Functionality (if equipped)
•      Test operation of power folding top
Perform with engine running to conserve battery power
Post-Road Test Inspection
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Effective 7-11-2019-US
Version 1.8
Model Year 2019 | Audi Pre-Delivery Reference Document | 28