122-F9L4Q-04
Service Bulletin Details
Public Details for: 122-F9L4Q-04
Instructions for retrofitting the sport design package on the macan and macan s
Models from 2020
2020 PORSCHE MACAN |
Models from 2019
2019 PORSCHE MACAN |
2019 PORSCHE MACAN S |
Installation and Conversion Instructions Macan (95B) 2/19 ENU 6699 6 SportDesign Package (2D2/2D6) Vehicle type: Macan (95B)/Macan S (95B) Model Year: As of 2019 Restriction: ONLY approved for vehicles produced from week 35/2018! Information: Retrofitting Figure 1 Notes: The SportDesign package ( Figure 1) further emphasises the sporty nature of the Macan. The SportDesign package comprises the following components: • • • • New front apron New ready-primed door trim panels (ONLY for 2D6) New ready-primed rear spoiler New rear skirt, rear panel and underride guard (rear) The components have been tested and approved together. Installing of individual components is not permitted or approved! The components specified above are also available straight from the factory for new vehicles by requesting optional equipment SportDesign package (2D2)/SportDesign package painted Black (high-gloss – 2D6). The respective optional equipment is differentiated in terms of the scope of parts and the paint finish (Matt Black or High-Gloss Black) of the individual parts. Tequipment Mar 4, 2020 Page 1 of 17 6 Macan (95B) 6699 ENU Installation and Conversion Instructions 2/19 For I-no. 2D2, we recommend the following paint finish: • • Matt Black (OK1): All grilles (radiators, vents), trims (fog lights, front camera) and parking sensor (inner) Exterior color: All large parts (complete front/rear apron, front spoiler and roof spoiler), cover for towing hook and parking sensor (outer) For I-no. 2D6, we recommend the following paint finish: • • High-Gloss Black (041): All grilles (radiators, vents), trims (fog lights, front camera), parking sensor (inner), rear panel AND door trim panels. Exterior color: All large parts (front apron/rear skirt, front spoiler and roof spoiler), cover for towing hook and parking sensor (outer) The ready-primed sill covers (2D1)/sill covers and door trim panels (2D5) can also be retrofitted at the request of the customer. Available part numbers can be found in the TEQUIPMENT catalogue or the Porsche Electronic Parts Catalogue (PET). For installation instructions, working times and painting times, see Workshop Manual. Parts Info: 95B.044.815.00 SportDesign package – RoW, set 95B.044.815.01 SportDesign package – USA/Canada, set 95B.044.815.02 SportDesign package – Japan, set 95B.044.815.03 SportDesign package – China, set ONLY for retrofitting SportDesign package (high-gloss Black – 2D6), also order the following: 95B.044.802.00 Door trim panel, prime-coated – set ONLY for vehicles with ParkAssist (7X2/7X8/8A4), also order the following: 5Q0.919.275.B.G2X 2x ParkAssist sensor, prime-coated – inner 5Q0.919.275.C.G2X 2x ParkAssist sensor, prime-coated – outer ONLY for vehicles with trailer hitch (1D3 or 1D6), also order the following: 95B.807.925. .1E0 1x 95B.807.834.P.G2X 1x 95B.807.883 1x 95B.807.834.N.1E0 1x Rear grille, Black – RoW vehicles with electric trailer hitch (1D3) Rear trim, prime-coated – RoW vehicles with electric trailer hitch (1D3) Reinforcement, rear – USA/Canada vehicles with mechanical trailer hitch (1D6) Rear trim, Black – USA/Canada vehicles with mechanical trailer hitch (1D6) Also order the following supplementary sets according to market and vehicle equipment: Mar 4, 2020 Page 2 of 17 Tequipment Installation and Conversion Instructions Macan (95B) 2/19 ENU 6699 6 ONLY for USA/Canada vehicles: 95B.044.815.18 1x Enhanced SportDesign package – Basic vehicle, set 95B.044.815.19 1x 95B.044.815.20 1x 95B.044.815.21 1x Enhanced SportDesign package – Vehicles with ParkAssist (7X2/7X8/8A4), set Enhanced SportDesign package – Vehicles with adaptive cruise control (8T3), set Enhanced SportDesign package – Vehicles with ParkAssist (7X2/7X8/8A4) and adaptive cruise control (8T3), set Also order the following if necessary: 95B.898.056 1x Mounting parts for roof spoiler – set Parts list: Figure 2 Parts included for front apron ( Figure 2 ): 95B.807.217.x.G2X1 1x Front apron, prime-coated Figure 2 -1- 95B.807.221.x.G2X1 1x Front apron, prime-coated Figure 2 -1- 95B.807.156.E.G2X 1x Towing hook cover, prime-coated Figure 2 -2- 95B.807.061.J.G2X 1x Front spoiler, prime-coated Figure 2 -3- 95B.807.683.xx.G2X1 1x Radiator grille (centre), prime-coated Figure 2 -4- Tequipment Mar 4, 2020 Page 3 of 17 6 Macan (95B) 6699 ENU 95B.807.681.J.G2X Mar 4, 2020 Page 4 of 17 Installation and Conversion Instructions 2/19 Air grille – side (left), prime-coated Figure 2 -5- 1x 95B.807.682.J.G2X 1x Air grille – side (right), prime-coated Figure 2 -5- 95B.121.333.B3 1x Air guide – side, closed (left) Figure 2 -6- 95B.121.334.B3 1x Air guide – side, closed (right) Figure 2 -6- 95B.807.819.C.G2X 1x Trim (left), prime-coated Figure 2 -7- 95B.807.820.C.G2X 1x Trim (right), prime-coated Figure 2 -7- 95B.807.685.D.G2X 1x Vane (left), prime-coated Figure 2 -8- 95B.807.686.D.G2X 1x Vane (right), prime-coated (not shown) 95B.807.838 4 1x Air guide (bottom), closed Figure 2 -9- 95B.807.661 1x Z support (left) Figure 2 -10- 95B.808.661 1x Z support (right, not shown) 95B.971.095.xx1 1x Electric wire harness Figure 2 -11- 999.919.243.01 22 x Cap screw, 5.0 x 13 (number plate holder) Figure 2 -12- N.909.747.01 12 x Torx tapping screw, TP5 x 16 Figure 2 -13- 999.507.836.09 6x Clamp, 9.0 x 13.4/4.0 Figure 2 -14- N.038.501.3 6x Expansion rivet, A6.0 x 12.0 Figure 2 -15- WHT.004.935 4x Expander nut, TP5 x 15.5 (not shown) ——— 2x Spacer ring Figure 2 -16- 95B.807.287.xx.E02 1x Number plate bracket (not shown) 1 Depending on respective set 2 Depending on country version 3 ONLY for Macan 4 ONLY for Macan S Tequipment Installation and Conversion Instructions Macan (95B) 2/19 ENU 6699 6 Figure 3 Parts included for front ( Figure 3 ): 95B.807.550.P 1x Plastic foam strip (front) – RoW Figure 3 -1- 95B.807.550.Q 1x Plastic foam strip (front) – USA (not shown) 95B.117.335.E 1x Air guide on charge-air cooler (left) Figure 3 -2- 95B.117.336.E 1x Air guide on charge-air cooler (right) Figure 3 -3- 95B.121.699.J 1x Air flap (left) Figure 3 -4- 95B.121.700.J 1x Air flap (right) Figure 3 -5- 95B.825.101.E.1E0 1x Front underbody panelling (left) Figure 3 -6- 95B.825.102.E.1E0 1x Front underbody panelling (right) Figure 3 -7- Figure 4 Tequipment Mar 4, 2020 Page 5 of 17 6 Macan (95B) 6699 ENU Installation and Conversion Instructions 2/19 Parts included for rear ( Figure 4 ): 95B.827.934.B.G2X 1x Roof spoiler, prime-coated Figure 4 -1- 95B.807.521.AB.G2X1 1x Rear skirt, prime-coated – RoW Figure 4 -2- 95B.807.521.AE.G2X1 1x Rear skirt, prime-coated – Japan Figure 4 -2- 95B.807.521.AF.G2X1 1x Rear skirt, prime-coated – China Figure 4 -2- 95B.807.834.G.G2X5 1x Rear panel, prime-coated Figure 4 -3- 95B.807.8355 1x Underride guard Figure 4 -4- N .038.549.4 4x Expansion rivet, A8 x 12 (not shown) 5 Materials: Notes: ONLY for vehicles WITHOUT trailer hitch (1D3/1D6) ——— —— Micro-fiber cloth (commercially available) ——— —— Betaclean 3350/isopropanol (commercially available) The relevant legal regulations must be observed in the various countries. Information 9900 - PIWIS Tester 3 Tools: Polyoxymethylene wedge (POM wedge, commercially available) Soft-faced hammer (commercially available) Stanley knife (commercially available) Shop light Work Procedure: 1 Preparatory work CAUTION Painting components • Risk of warping of components • Risk of damage to components Observe the guidelines and instructions for painting components in the "Paint" Workshop Manual. Always place parts without tension on the painting devices provided during painting and drying processes. Mar 4, 2020 Page 6 of 17 1.1 Paint all prime-coated parts according to the relevant I-no. 2D2 (Matt Black = OK1) or 2D6 (High-Gloss Black = 041) and the vehicle's color code as specified in the Paint Manual. 1.2 Drive the vehicle onto the lifting platform ( Workshop Manual '4X00IN Lifting the vehicle'). Tequipment Installation and Conversion Instructions 2 Macan (95B) 2/19 ENU 6699 6 1.3 Connect battery charger ( Workshop Manual '2X00IN Battery trickle charging'). 1.4 Remove front apron ( Workshop Manual '631519 Removing and installing front apron'). 1.5 Remove rear apron ( Workshop Manual '635519 Removing and installing rear apron'). 1.6 Remove rear spoiler ( Workshop Manual '665819 Removing and installing rear spoiler'). Assemble new SportDesign front apron 2.1 Cut out transport lock on front apron ( Figure 5 ). 1 2 3 4 5 – – – – – Transport lock Front apron Cover on towing hook Radiator grille (center) Parking sensor holder (7X2/7X8/8A4) Remove burrs from cut edges. 2.2 Guide retaining strap for cover on towing hook into the front apron and fit cover in front apron. 2.3 Convert reinforcement (mounting for front apron at the top in the fender area at the left/right) ( Workshop Manual '63155501 Replacing front apron (basic)'). Figure 5 2.3.1 Remove expansion rivet (1 x) and reinforcement (left/right) from standard front apron. 2.3.2 Fit reinforcement (left/right) with expansion rivet (1 x) on new front apron. Information Check fixing clips. They must not be bent or broken. Make sure that all locking lugs have engaged correctly. Check that they are installed correctly. 2.4 Fit new painted radiator grille (center) on front apron ( Workshop Manual '660519 Removing and installing radiator grille'). Check gap dimension in the visible area all the way around and correct it if necessary. Information Check fixing clips. They must not be bent or broken. Make sure that all locking lugs have engaged correctly. Check that they are installed correctly. Tequipment Mar 4, 2020 Page 7 of 17 6 Macan (95B) 6699 ENU 2.5 Installation and Conversion Instructions 2/19 Fit new painted front spoiler on front apron ( Workshop Manual '660319 Removing and installing front spoiler') and secure with expansion rivets A6.0 x 12.0 (4 x). Check gap dimension in the visible area all the way around and correct it if necessary. 2.6 Work in the (center) radiator grille area 2.6.1 Fit Z support (left/right) in the (center) radiator grille ( Figure 6 ). 1 2 3 – Radiator grille (center) – Z support (left) – Z support (right) Figure 6 2.6.2 Fit spacer ring (2 x) using pliers in tab on (center) radiator grille at the top ( Figure 7 ). 1 2 2.6.3 – Spacer ring – Clamp, 9.0 x 13.4/4.0 Fit clamp 9.0 x 13.4/4.0 (6 x) in the edge of the (center) radiator grille at the top ( Figure 7 ). Figure 7 Mar 4, 2020 Page 8 of 17 Tequipment Installation and Conversion Instructions Macan (95B) 2/19 ENU 6699 6 Information Check fixing clips. They must not be bent or broken. Make sure that all locking lugs have engaged correctly. Check that they are installed correctly. 2.6.4 ONLY for vehicles with ParkAssist (7X2/7X8/8A4): Fit parking sensor holder into new painted radiator grille (center). 1 2 – Parking sensor holder (7X2/7X8/8A4) – Radiator grille (center) Convert parking sensor (4 x) ( Workshop Manual '917519 Removing and installing ParkAssist sensor'). Figure 8 Make sure that the isolating ring on the parking sensor is fitted correctly! Check gap dimension in the visible area all the way around and correct it if necessary. 2.6.5 ONLY for vehicles with front and rear ParkAssist incl. reversing camera and Surround View (8A4): Convert trim with holder and front camera ( Figure 9). 1 2 3 4 – – – – Cover Bracket Front camera Cap screw, 5.0 x 13 Cap screw, 5.0 x 13: Tightening torque 2 Nm (1.5 ftlb.) 2.7 Figure 9 Work in the air grille area (side, left/right) Tequipment Mar 4, 2020 Page 9 of 17 6 Macan (95B) 6699 ENU Installation and Conversion Instructions 2/19 Information Check fixing clips. They must not be bent or broken. Make sure that all locking lugs have engaged correctly. Check that they are installed correctly. 2.7.1 Fit new air grilles (side, left/right) in the front apron ( Figure 10 ; Workshop Manual '66041921 Removing and installing front air grille (Turbo)'). 1 2 – Air grille (side, right) – Front apron Figure 10 2.7.2 Fit new vane (left/right) into the respective air grille ( Figure 11 ). 1 2 – Vane (left) – Direction indicator light/auxiliary headlight (left) Figure 11 Mar 4, 2020 Page 10 of 17 Tequipment Installation and Conversion Instructions 2.7.3 Macan (95B) 2/19 ENU 6699 6 Convert direction indicator light/auxiliary headlights (left/right) ( Figure 12; Workshop Manual '947119 Removing and installing auxiliary headlights'). 1 2 – Direction indicator light/auxiliary headlight (left) – Torx tapping screw, TP5 x 16 Secure direction indicator light/auxiliary headlights (left/right) using Torx tapping screws (TP5 x 16, 3 x). Figure 12 Tightening torque 2 Nm (1.5 ftlb.) 2.7.4 ONLY for USA variant: Convert side marker light ( Workshop Manual '942755 Replacing light bulb for side marker light'). 2.7.5 Fit painted trim (left/right) in the front apron on the relevant side from the outside ( Figure 13 ). 1 2 2.7.6 2.8 – Trim (right) – Front apron Check gap dimension in the visible area all the way around and correct it if necessary. Fit air guides, depending on the vehicle Figure 13 Tequipment Mar 4, 2020 Page 11 of 17 6 Macan (95B) 6699 ENU Installation and Conversion Instructions 2/19 2.8.1 ONLY for Macan: Fit air guide – side, closed (left/right) on the relevant air grille and secure with Torx tapping screws (TP5 x 16, 2 x) ( Figure 14). 1 2 – Air guide – side, closed (right) – Torx tapping screw, TP5 x 16 Torx tapping screw, TP5 x 16: Tightening torque 2 Nm (1.5 ftlb.) Figure 14 2.8.2 ONLY for Macan S: Fit air guide (bottom), closed, in the radiator grille (center) at the bottom and secure with Torx tapping screws (TP5 x 16, 2 x) ( Figure 15). 1 2 3 – Air guide (bottom), closed – Torx tapping screw, TP5 x 16 – Radiator grille (center) Torx tapping screw, TP5 x 16: Tightening torque 2 Nm (1.5 ftlb.) 2.9 3 Mar 4, 2020 Page 12 of 17 Figure 15 Route new electric wire harness in the front apron and connect it ( Workshop Manual '971519 Removing and installing front wire harness'). Fit new SportDesign front apron Tequipment Installation and Conversion Instructions 3.1 Macan (95B) 2/19 ENU 6699 6 Work in the vehicle front area 1 2 3 3.1.1 – Plastic foam strip (front) – Air flap (right) – Air guide on charge-air cooler (right) Replace plastic foam strip (front Figure 16 (Turbo) -1-) with new plastic foam strip ( Workshop Manual '631019 Removing and installing front bumper'). 4 3.1.2 Replace air flap (left/right Figure Figure 16 (Turbo) 16 (Turbo) -2-) with new air flap (left/right) ( Workshop Manual '631019 Removing and installing front bumper') 3.1.3 Replace air guide for charge-air cooler (left/right Figure 16 (Turbo) -3-) with new air guide (left/right) ( Workshop Manual '211019 Removing and installing air guide for charge-air cooler'). 3.2 Install new SportDesign front apron with new underbody panelling (left/right) ( Workshop Manual '631519 Removing and installing front apron'). 3.3 Fit new license plate bracket on new SportDesign front apron ( Workshop Manual '668319 Removing and installing number plate cover'; Workshop Manual '668319 Removing and installing number plate cover (USA)'). Convert rear apron 4.1 Remove rear skirt ( Workshop Manual '636819 Removing and installing rear skirt'). Information Check fixing clips. They must not be bent or broken. Make sure that all locking lugs have engaged correctly. Tequipment Mar 4, 2020 Page 13 of 17 6 Macan (95B) 6699 ENU Installation and Conversion Instructions 2/19 Check that they are installed correctly. 4.2 Install new painted rear skirt in rear apron ( Figure 17; Workshop Manual '636819 Removing and installing rear skirt') 1 2 3 4 – – – – Painted rear skirt Rear apron Installation position of reversing light Painted rear panel Check gap dimension in the visible area all the way around and correct it if necessary. 4.3 ONLY for vehicles with reversing camera Figure 17 (7XB/8A4): Install reversing camera ( Workshop Manual '914319 Removing and installing reversing camera'). 4.4 Install reversing light (left/right) ( Workshop Manual '947419 Removing and installing reversing light'). Check gap dimension in the visible area all the way around and correct it if necessary. 4.5 Install new painted rear panel ( Figure 17 -4-) ( Workshop Manual '635619 Removing and installing rear panel') Check gap dimension in the visible area all the way around and correct it if necessary. 4.6 Install rear apron with new underride guide ( Figure 18; Workshop Manual '635519 Removing and installing rear apron'). 1 2 3 4 4.7 5 6 Mar 4, 2020 Page 14 of 17 – – – – Underride guard Painted rear panel Painted rear skirt License plate carrier Convert license plate bracket. Convert rear spoiler. 5.1 Remove rear spoiler ( Workshop Manual '665819 Removing and installing rear spoiler'). 5.2 Install new rear spoiler painted in exterior color. ONLY for retrofitting SportDesign package (high-gloss Black - 2D6): Convert door trim panels Tequipment Figure 18 Installation and Conversion Instructions Coding: 7 Macan (95B) 2/19 ENU 6699 6 6.1 Remove cover on front door and install new painted cover ( Workshop Manual '662219 Removing and installing cover for front door'). 6.2 Remove cover on rear door and install new painted cover ( Workshop Manual '664219 Removing and installing cover for rear door'). Enter SportDesign package (2D2 or 2D6) in the vehicle data 7.1 Preparatory work – Coding NOTICE Voltage drop • Risk of irreparable damage to control unit • Risk of damage to control unit • Fault entries in the control unit • Coding in the control unit is aborted • Malfunctions in control unit, even during programming Switch off the ignition and remove the ignition key before disconnecting the control unit. Ensure that the power supply is not interrupted during programming. Connect a battery charger with a current rating of at least Nominal value 90 A to the vehicle battery. NOTICE Control unit programming will be aborted if the Internet connection is unstable. • An unstable Internet connection can interrupt communication between PIWIS Tester III and the vehicle communication module (VCI). As a result, control unit programming may be aborted. During control unit programming, always connect PIWIS Tester III to the vehicle communication module (VCI) via the USB cable. 7.1.1 9900 - PIWIS Tester 3 must be connected to the vehicle and then switched on. 7.1.2 Switch on ignition AND hazard warning lights on the vehicle. Information The 9900 - PIWIS Tester III instructions take precedence since the description may be different with later Tester releases. The procedure described here has been structured in general terms; different text or additions may appear on the 9900 - PIWIS Tester III. 7.1.3 Select the "Diagnostics" menu item on the PIWIS Tester. Tequipment Mar 4, 2020 Page 15 of 17 6 Macan (95B) 6699 ENU 2/19 7.1.4 7.2 Installation and Conversion Instructions If 9900 - PIWIS Tester 3 is connected correctly, a connection to the vehicle will be established: "Macan model line" is detected. Enter the new vehicle equipment in the vehicle data 7.2.1 Press •F7“ in the control unit overview to switch to the “Additional menu”. Press •F12“ to confirm the question "Create Vehicle Analysis Log (VAL)?". 7.2.2 Select the “Management of vehicle order” function. Continue pressing •F12“ until “PR numbers” is displayed in the Value group column. 7.2.3 Look for the option "2D2 – SPORT DESIGN PACKAGE WITHOUT SILL COVERS" or "2D6 – SPORT DES. PACKAGE W/O DOOR SILLS, BLACK" in the "Family" column. Select the relevant option from the drop-down menu in the "Value" column. 7.3 7.2.4 Press •F12“ to continue. A table containing coding values (old and new value) is displayed in the overview. 7.2.5 Press •F8“ to continue. Data is then written/stored. 7.2.6 Wait until the message “Creation of vehicle data has been completed.” appears. Press •F12“ to go to Report management. 7.2.7 Press •F10“ to open the log. Check that the selected vehicle equipment has been entered and close the log. Code/program the new vehicle equipment. 7.3.1 Select ALL control units (•CTRL+A“) in the control unit overview and switch to the “Coding/programming” column. 7.3.2 Select the coding mode "Automatic coding". Press •F12“ to continue. 7.3.3 Once "Automatic coding" is complete, the message “Coding was completed successfully. Press •F12“ to continue.” appears in the header. Switch to the control unit overview. 51 01 71 05: Mar 4, 2020 Page 16 of 17 7.4 Read out the fault memory of all systems, work through any existing faults and erase the fault memory ( Workshop Manual '0X03IN Diagnostic maintenance: Diagnostic system and maintenance inter...'). 7.5 Switch off ignition and disconnect 9900 - PIWIS Tester 3. 7.6 Disconnect battery charger. ( Workshop Manual '2X00IN Battery trickle charging'). –Preparing body paintwork– Includes: Order-based Painting of new parts, Step 1 Plastic component Tequipment Labor time: 130 TU Installation and Conversion Instructions Macan (95B) 2/19 ENU 6699 6 66 99 61 51: –Painting new parts in SportDesign package (1 x), complete Includes: Painting new parts, Step 1: Front apron, towing hook cover, front spoiler, radiator grille (center), air grille (left/right), vane (left/right), trim on direction indicator/auxiliary headlights (left/right), trim panel (left/right) and front camera trim; roof spoiler, rear skirt and rear panel. Materials: 38 MU Labor time: 510 TU 66 99 23 10: –Installing SportDesign package (1 x)– Includes: Removing and installing front and rear apron. Assembling new front apron and converting rear apron. Removing rear spoiler and installing new rear spoiler. Labor time: 630 TU 03 35 00 50: –On-board diagnosis– Includes: Coding SportDesign package (I-no. 2D2 or I-no. 2D6) in the vehicle data using the PIWIS Tester. Additional working times: ONLY for retrofitting SportDesign package (high-gloss Black – 2D6): Labor time: 12 TU 66 22 61 51: Painting new front door trim panel Labor time: 20 TU 66 42 61 51: Painting new rear door trim panel Labor time: 20 TU 66 22 56 00: Replacing front door trim panel (left/right) Labor time: 75 TU 66 42 56 50: Replacing rear door trim panel (left/right) Labor time: 58 TU ONLY for vehicles with Lane Change Assist/Lane Keep Assist (7Y2/7Y3/7Y7): 97 70 25 53: Programming Lane Change Assist control unit. Includes: Calibrating calibration plate on the vehicle. Labor time: 47 TU ONLY for vehicles with Surround View (8A4): 91 72 25 50: Programming Surround View camera control unit Labor time: 62 TU Important Notice: Technical Bulletins issued by Porsche Cars North America, Inc. are intended only for use by professional automotive technicians who have attended Porsche service training courses. They are written to inform those technicians of conditions that may occur on some Porsche vehicles, or to provide information that could assist in the proper servicing of a vehicle. Porsche special tools may be necessary in order to perform certain operations identified in these bulletins. Use of tools and procedures other than those Porsche recommends in these bulletins may be detrimental to the safe operation of your vehicle, and may endanger the people working on it. Properly trained Porsche technicians have the equipment, tools, safety instructions, and know-how to do the job properly and safely. Part numbers listed in these bulletins are for reference only. The work procedures updated electronically in the Porsche PIWIS diagnostic and testing device take precedence and, in the event of a discrepancy, the work procedures in the PIWIS Tester are the ones that must be followed. © 2020 Porsche Cars North America, Inc. Tequipment Mar 4, 2020 Page 17 of 17