122-C8W5S-04

Installation and Conversion Instructions
Macan (95B)
26/14
ENU
6316
6
Stainless Steel Skid Plate (2JC)
Information:
Retrofitting
Model Year:
As of 2014 up to 2018
Vehicle Type:
Macan Turbo
Restriction:
NOT in conjunction with SportDesign package (I-no. 2D1 / 2D2 / 2D5 / 2D6).
Figure 1
Note:
The stainless steel skid plate gives the Macan a customized look and makes it appear even more
powerful and dynamic.
The stainless steel skid plate is available separately under the optional equipment item "2JC" and in
combination with the stainless steel rear panel under the optional equipment item "2JX", also for new
vehicles ex-works.
The combination with the stainless steel rear panel is recommended.
Part Info:
95B.807.833.A 6M7
Material:
———
 Stainless steel skid plate, set for Turbo
——
Isopropanol (commercially available)
Tequipment
Mar 23, 2020
Page 1 of 10
6
Macan (95B)
6316
Tools:
ENU
Installation and Conversion Instructions
26/14
9900 - PIWIS Tester 3
Polyoxymethylene wedge (POM wedge, commercially available)
Soft-faced hammer (commercially available)
Stanley knife (commercially available)
Saw or vibrating knife
Round/flat file
Side cutters
Flat scraper
Flashlight
Assembly:
1
Preparatory work.
1.1
Connect battery charger (  Workshop Manual '2X00IN Battery trickle charging').
1.2
Remove front apron (  Workshop Manual '631519 Removing and installing front apron').
1.3
Remove rear panel (  Workshop Manual
'631619 Removing and installing rear
panel' Figure 2).
1
2
3
– Tab
– Skid plate
– Front apron
1.3.1
Remove license plate cover.
Workshop Manual '668319
Removing and installing license plate cover'
1.3.2
Remove clamp ( Figure 3 -1-).
1
Figure 2
– Clip
Figure 3
Mar 23, 2020
Page 2 of 10
Tequipment
Installation and Conversion Instructions
1.3.3
Macan (95B)
26/14
ENU
6316
6
Release the tabs from the center of
the front apron in the sequence A,
B, C and D using a plastic spatula
( Figure 4 -arrow a-). Carefully
pull the skid plate downwards at the
same time ( Figure 4 -b-).
Figure 4
When guiding out the (inner) tab,
the (outer) tab moves inwards (
Figure 5 -arrow-).
The skid plate can only be guided
out of the front apron without
damaging it irreparably from
position  Figure 5 -B-.
1
– (Outer) tab
Figure 5
Tequipment
Mar 23, 2020
Page 3 of 10
6
Macan (95B)
6316
ENU
Installation and Conversion Instructions
26/14
1.4
Remove front spoiler from the front apron
( Figure 6).
1
2
3
4
–
–
–
–
Tab
Front spoiler
Front apron
Front spoiler seam
Figure 6
1.4.1
Press down the locking lug (
Figure 7 -arrow a-) and unclip front
spoiler from front apron ( Figure 7
-arrow-).
1
2
1.4.2
– Locking lug
– Front spoiler
Guide outer tabs on the front spoiler
( Figure 7 -1-) out of the front
apron and remove front spoiler (
Figure 7 -2-).
Figure 7
CAUTION
Machining work (drilling, filing, grinding, etc.)
•
Risk of damage to electric wires
•
Risk of damage to components
•
Risk of damage to painted surfaces

Exercise extreme care while working. Use a bit stop while drilling if necessary.

Cover and, if necessary, mask surfaces that are at risk (painted surfaces, wood or carbon look parts
and so on).
CAUTION
Pointed or sharp objects
•
Risk of nicks, cuts or scrapes

Wear personal protective gear.
2
Install stainless steel skid plate.
2.1
Mar 23, 2020
Page 4 of 10
Remove edges on the front spoiler.
Tequipment
Installation and Conversion Instructions
2.1.1
Macan (95B)
26/14
ENU
6316
6
Remove edge on the front spoiler
close to the six mounting points (
Figure 8 -inset A-) and the center
( Figure 8 -inset B-) using a
cutter (Stanley knife).
1
– Edge
Figure 8
2.1.2
Remove edge on the front spoiler
at the outer left and right using a
cutter (Stanley knife) ( Figure 9).
1
A
B
C
– Edge
– Front spoiler without
edge turned 180°
– Front spoiler without edge
– Front spoiler with edge
Figure 9
Tequipment
Mar 23, 2020
Page 5 of 10
6
Macan (95B)
6316
ENU
Installation and Conversion Instructions
26/14
2.2
Make a cut-out in the front spoiler ( Figure
10).
1
2
3
2.3
– Front spoiler
– Embossing
– Pneumatic saw
2.2.1
Mark the impression using a
pen/marker ( Figure 10 -2-) if
necessary.
2.2.2
Use an air saw to cut out the cut-out
in the front spoiler ( Figure 10
-inset-).
Pull protective film off the edge of the skid
plate.
Figure 10
2.4
Install front spoiler on the skid plate ( Figure
11).
1
2
– Front spoiler
– Skid plate
Figure 11
Mar 23, 2020
Page 6 of 10
Tequipment
Installation and Conversion Instructions
2.5
Macan (95B)
26/14
ENU
6316
6
Secure stainless steel skid plate.
1
2
– Retaining lug
– Flat-nosed pliers
2.5.1
Bend the rear holders by 180° (
Figure 12 -arrow a-).
2.5.2
Press retaining lugs down by
approx. 30° ( Figure 12 -inset-).
Counter using flat-nosed pliers or a
similar tool.
Figure 12
2.6
Install the front spoiler on the front apron.
1
2
– Front spoiler
– Tab
2.6.1
Position the front spoiler in the gap
on the front apron with the help of
another mechanic ( Figure 13
-Arrows-).
2.6.2
Guide outer tabs into the front apron
( Figure 13).
2.6.3
Press front spoiler on evenly until
the clips lock securely.
Figure 13
Tequipment
Mar 23, 2020
Page 7 of 10
6
Macan (95B)
6316
ENU
Installation and Conversion Instructions
26/14
2.7
Installing rear panel
1
2
3
– Skid plate
– Front apron
– (Outer) tab
2.7.1
Position skid plate in the gap on the
front apron ( Figure 14 -Arrows-).
First guide the (outer) tab at the left
and right ( Figure 14 -3-) into the
front apron  Figure 14 -arrow b-.
2.7.2
Then press the skid plate into the
front apron from the outside in until
the inner tabs engage.
The (outer) tabs slide into their end
position ( Figure 14 -a-).
Figure 14
2.7.3
Install clamp ( Figure 15).
1
2.7.4
2.8
3
– Clip
Install license plate cover. 
Workshop Manual '668319
Removing and installing license
plate cover'
Pull the remaining protective film off the
skid plate and clean the skid plate with
isopropanol.
Figure 15
Concluding work.
3.1
Install front apron.  Workshop Manual '631519 Removing and installing front apron'
NOTICE
Voltage drop
•
Risk of irreparable damage to control unit
•
Risk of damage to control unit
•
Fault entries in the control unit
•
Coding in the control unit is aborted
•
Malfunctions in control unit, even during programming

Switch off the ignition and remove the ignition key before disconnecting the control unit.
Mar 23, 2020
Page 8 of 10
Tequipment
Installation and Conversion Instructions
Macan (95B)
26/14
ENU
6316
6

Ensure that the power supply is not interrupted during programming.

Connect a battery charger with a current rating of at least Nominal value 90 A to the vehicle
battery.
Information
The 9900 - PIWIS Tester III instructions take precedence since the description may be
different with later Tester releases.
The procedure described here has been structured in general terms; different text or
additions may appear on the 9900 - PIWIS Tester III.
3.2
Maintenance of vehicle data.
3.2.1
9900 - PIWIS Tester 3 must be connected before switching on the ignition.
3.2.2
Select the required vehicle type. PIWIS Tester II Diagnostics starts.
3.2.3
Select Additional menu by pressing •F7“. Press •F11“ to confirm the question
"Create vehicle analysis log (VAL)?".
3.2.4
Select the "Maintenance of vehicle data" function.
Press •F12“ until "PR numbers" appears in the Value group column.
3.2.5
Select "Bumper" in the Family column.
3.2.6
Open drop-down menu and select "2JC – Comfort bumper (front panel)". Press
•F12“ to continue.
3.2.7
A table containing the values to be changed appears.
Save the values by pressing •F8“.
Wait until "Generation of vehicle data is complete........" appears.
3.2.8
Press •F12“ to switch to Report management.
Open the log by pressing •F10“ and check whether vehicle equipment "2JC –
Comfort bumper (front trim)" is entered. Close the log.
3.3
3.2.9
Read out the fault memories of all systems, work through any existing faults
and erase the fault memories.  Workshop Manual '033500 Fault memory for
on-board diagnosis'
3.2.10
Switch off ignition and disconnect 9900 - PIWIS Tester 3.
Disconnect the battery charger.  Workshop Manual '2X00IN Battery trickle charging'
Tequipment
Mar 23, 2020
Page 9 of 10
6
Macan (95B)
6316
63 16 23 30:
ENU
26/14
Installation and Conversion Instructions
Stainless steel skid plate installed
Includes:
Removing and installing front apron, removing and installing
front spoiler.
Labor time: 270 TU
Important Notice: Technical Bulletins issued by Porsche Cars North America, Inc. are intended only for use by professional automotive technicians who have attended Porsche service training
courses. They are written to inform those technicians of conditions that may occur on some Porsche vehicles, or to provide information that could assist in the proper servicing of a vehicle. Porsche special
tools may be necessary in order to perform certain operations identified in these bulletins. Use of tools and procedures other than those Porsche recommends in these bulletins may be detrimental to the
safe operation of your vehicle, and may endanger the people working on it. Properly trained Porsche technicians have the equipment, tools, safety instructions, and know-how to do the job properly and
safely. Part numbers listed in these bulletins are for reference only. The work procedures updated electronically in the Porsche PIWIS diagnostic and testing device take precedence and, in the event of a
discrepancy, the work procedures in the PIWIS Tester are the ones that must be followed.
© 2020 Porsche Cars North America, Inc.
Mar 23, 2020
Page 10 of 10
Tequipment