2059124/1

Field campaign
Topic
Market area
Brand
Transaction No.
Campaign number
Note
Type
US code
V8 Kovomo - Control module updates (SC20/09)
United States E05 Bentley USA and rest America (6E05)
Bentley
2059124/1
EB51
Vehicle data
New Continental GT and Bentayga
Sales types
Type MY Brand Designation Engine code Gearbox code Final drive code
3S3* 2020 E
*
*
*
4V1* 2019 E
*
*
*
Chassis numbers
Manufacturer
SJA
SJA
SJA
SJA
SJA
SJA
SJA
SJA
SCB
SCB
Filler
AM2
AM2
AM2
AM2
AM2
AM2
AM2
AM2
CG2
CG2
Documents
Document name
master.xml
Type
ZV
ZV
ZV
ZV
ZV
ZV
ZV
ZV
ZG
ZG
Filler
9
8
X
3
0
2
1
4
6
1
MY
K
K
K
K
K
K
K
K
L
L
Factory
C
C
C
C
C
C
C
C
C
C
From
023721
023726
023727
023729
023722
023723
023728
023724
074615
074912
To
Prod from Prod to
023721
023726
023727
023729
023722
023723
023728
023724
074615
074912
EB51
V8 Kovomo - Control module updates (SC20/09)
Notes
Transaction No.: 2059124/1
Release date: Mar 27, 2020
Repair instructions
Technical background
New Continental GT
Software update required to the engine control module and transmission control module
Bentayga
Software update required to the transmission control module
Please ensure the operative uses the applicable SVM code for the correct vehicle type
Remedy
Software update required for the applicable control modules depending on vehicle type
Customer notification
Customers do not need to be informed directly of this campaign. Please ensure that all affected vehicles are repaired immediately, or if the
vehicle is a Retailer demonstrator or stock vehicle the update must be conducted before sale
Warranty
Warranty Type
Damage Service Number
Damage Code
Labour Operation Code
Time
Criterion ID
710 or 790
EB51
00 66
01 29 00 05
50 Time units
01
Parts
Not applicable
Parts supply
Not applicable.
Parts despatch control
Not applicable.
Repair instructions
Notes
Technical background
New Continental GT
Software update required to the engine control module and transmission control module
Bentayga
Software update required to the transmission control module
Please ensure the operative uses the applicable SVM code for the correct vehicle type
Check
If the vehicle is not already listed as repaired in the ‘Repair history’ section of ElsaPro, check for the presence of the silver campaign identification
mark as per the Identification section of this TPI. In the event the campaign has not been applied, please carry out the required work in
accordance with these instructions.
Parts
Not applicable
Work
IMPORTANT: Transport mode and loading mode must be deactivated before the procedure within this document is conducted
General information before the software update is conducted:
• The closed-circuit voltage of the vehicle must be at least 12.5 V during the update. Connect a suitable battery charger to
the vehicle. For further information refer to the Repair manual.
• During the update switch off all unnecessary consumers (ventilation, seat heater, interior illumination etc)
• Because of the highest transmission stability you MUST use the diagnosis interface VAS 6154 (WiFi diagnostic tool) ONLY
in USB operation or the cable-connected VAS 5055 for the reprogramming (updating) of control units. If these units are
not available, the diagnosis interface VAS 5054 (A) can also be used in USB mode
• Do Not under any circumstances use a Bluetooth connection to conduct the reprogramming (updating) of control units
1. Select and run Guided fault finding. Within the Special functions tab select SVM – Problem related Hardware/Software update then select
Perform test (Figure 1)
Figure 1
New Continental GT
2. On the next screen enter the SVM code 370ENG01 and select Adopt (Figure 2)
Figure 2
Bentayga
On the next screen enter the SVM code 4V002SW1002 and select Adopt (Figure 3)
Figure 3
3. On the following screen, confirm the SVM code is correct and select Yes.
4. All control modules will now be interrogated.
5. The applicable software update will then be suggested (depending on vehicle type) - select Yes.
6. A progress bar will be displayed.
7. Once the software update is complete, a confirmation screen will be evident to clarify the update has been successful (Figure 4)
Figure 4
IMPORTANT: Attempt to clear All DTC’s before the next part of the procedure is conducted
8. Select Guided functions from 01 – Engine Control Module 1
•
Select Basic settings (Figure 5)
Figure 5
•
Select Readiness code Figure 6 (Point A)
•
Select Execute (Point B)
Figure 6
9. At this point check and confirm the actual readiness code, the readiness code MUST be as shown in Figure 7
Should the readiness code bytes be 00000000 NO FURTHER ACTION IS REQUIRED
Should ANY of the bytes be 1, YOU MUST repeat the Basic settings test again from step 8. Once complete you must then
recheck and confirm the readiness code is 00000000
Figure 7
Bentayga
10. On completion apply a silver campaign identification mark as Figure 8
Figure 8
New Continental GT
•
On completion apply a silver campaign identification mark as Figure 9
Figure 9
Identification
Silver campaign identification mark as shown in Figures 8 and 9 (Depending on vehicle type)
Repair instructions
Notes