20-BD-009H

GROUP
BODY INTERIOR
DATE
Technical Service Bulletin
SUBJECT:
March 2020
NUMBER
20-BD-009H
MODEL(S)
Genesis (DH)
FRONT SEAT NOISE AND WOBBLE MOVEMENT REPAIR
This TSB supersedes 19-BD-006H Front Seat Noise Repair and 17-BD-003 Front Seat Tilt Pipe
Housing Replacement to include wobble movement as a possible condition.
Description: Some vehicles may experience seat noise and/or possible wobble movement from the
seat bottom when the vehicle is turning. This bulletin describes the procedure to install an e-ring clip
to the tilt pipe housing on the front seat.
Applicable Vehicles: 2015MY – 2016MY Genesis (DH)
Parts Information:
PART NAME
PART NUMBER
E-RING KIT
QTY
1
(6 e-rings in
package)
88535-B1000FFF
Circulate To: General Manager, Service Manager, Parts Manager, Warranty Manager, Service
Advisors, Technicians, Body Shop Manager, Fleet Repair
SUBJECT:
FRONT SEAT NOISE AND WOBBLE MOVEMENT REPAIR
Warranty Information:
MODEL OP CODE
OPERATION
OP TIME
CAUSAL
PART
Genesis
88535F00
(DH)
FRONT SEAT E-RING
INSTALLATION (ONE
SIDE)
0.3 M/H
88110-B1160
Genesis
88535F01
(DH)
FRONT SEAT E-RING
INSTALLATION (BOTH
SIDES)
0.4 M/H
NATURE
CODE
CAUSE
CODE
Q55
ZZ1
88110-B1160
Service Procedure:
1.
Adjust seat back (A) forward and move seat
forward to furthest positions using seat
switch (B).
A
B
2.
Pull the rear seat track covers (C) backward
and remove them.
C
TSB #: 20-BD-009H
Page 2 of 6
SUBJECT:
SUBJECT:
FRONT SEAT NOISE AND WOBBLE MOVEMENT REPAIR
Remove the 14MM mounting bolts (D) on
each side.
NOTICE
Tightening Torque: 49.0~63.7 Nm
(5.0~6.5 kgf.m, 36.1~47.0 lb-ft)
3.
Move seat backward to furthest position.
4.
Lift the front seat track cover (E) and
remove the 14MM mounting bolts (F) on
each side.
D
NOTICE
Tightening Torque: 49.0~63.7
Nm (5.0~6.5 kgf.m, 36.1~47.0 lbft)
TSB #: 20-BD-009H
E
Page 3 of 6
SUBJECT:
FRONT SEAT NOISE AND WOBBLE MOVEMENT REPAIR
SUBJECT:
F
5.
Tilt the seat (G) back as shown to the right.
!
G
CAUTION
Do not pull on lower seat
harness when tilting seat.
6.
Move the seat cushion upward to the max
position using the seat controls for the seat
cushion.
TSB #: 20-BD-009H
Page 4 of 6
SUBJECT:
SUBJECT:
7.
FRONT SEAT NOISE AND WOBBLE MOVEMENT REPAIR
Inspect the gap (J) between the tilt housing
(H) and pipe edge (I) on both sides of seat.
J
H
8.
I
Insert the E-ring (K) between the tilt housing
(H) and pipe edge (I).
H
K
I
9.
Using a flathead screwdriver, insert the
E-ring completely.
TSB #: 20-BD-009H
Page 5 of 6
SUBJECT:
SUBJECT:
FRONT SEAT NOISE AND WOBBLE MOVEMENT REPAIR
10.
Tap lightly using a hammer to ensure E-ring
is in place.
11.
Install up to 3 E-rings until the gap is no
longer present.
NOTICE
Driver/Passenger seat: Maximum
of 3 E-rings each side of seat.
12.
Place seat down and move the seat
cushion 3 times up/down and confirm
repair.
Reinstall components in reverse order.
TSB #: 20-BD-009H
Page 6 of 6
SUBJECT: