ITB20-010
Service Bulletin Details
Public Details for: ITB20-010
Models from 2020
2020 INFINITI QX60 |
Models from 2019
2019 INFINITI QX60 |
Models from 2018
2018 INFINITI QX60 |
Models from 2017
2017 INFINITI QX60 |
Classification: Reference: Date: EC20-011 ITB20-010 March 20, 2020 2017-2020 QX60; MIL ON WITH DTC P0101 STORED APPLIED VEHICLE: 2017-2020 QX60 (L50) APPLIED ENGINE: VQ35DD (V6) IF YOU CONFIRM The MIL is ON and DTC P0101 (MAF SEN/CIRCUIT-B1) is stored in the ECM. ACTION 1. Confirm the current ECM part number. 2. Reprogram the ECM, if applicable. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti retailer to determine if this applies to your vehicle. 1/4 SERVICE PROCEDURE 1. Using C-III plus, confirm the current ECM part number and write it on the repair order. If it matches one of the part numbers in Table 1, continue to step 2 on page 4. If it does not match one of the part numbers in Table 1, this bulletin does not apply. Go back to ASIST for further diagnostic and repair information. Table 1 MODEL YEAR CURRENT ECM PART NUMBER: 237103JR9A, 3JR9B, 3JR9C 3JS9A, 3JS9B, 3JS9C 6JA3A, 6JA3B, 6JA3C, 6JA3D 6JA4A, 6JA4B, 6JA4C, 6JA4D 6JA5A, 6JA5B, 6JA5C, 6JA5D 6JA7A, 6JA7B, 6JA7C, 6JA7D 6JA8A, 6JA8B, 6JA8C, 6JA8D 6JA9A, 6JA9B, 6JA9C, 6JA9D 9NC5A, 9NC5B, 9NC5C 9NC6A, 9NC6B, 9NC6C 9NC7A, 9NC7B, 9NC7C 9NC8A, 9NC8B, 9NC8C 9NC9A, 9NC9B, 9NC9C 9ND9A, 9ND9B, 9ND9C 9NJ1A, 9NJ1B, 9NJ1C, 9NJ1D 9NJ2A, 9NJ2B, 9NJ2C, 9NJ2D 9PF8A, 9PF8B, 9PF8C, 9PF8D 9NP0A, 9NP0B, 9NP0C, 9NP0D 9NP1A, 9NP1B, 9NP1C, 9NP1D 9NP2A, 9NP2B, 9NP2C, 9NP2D 9NP3A, 9NP3B, 9NP3C, 9NP3D 9NP4A, 9NP4B, 9NP4C, 9NP4D 9NP5A, 9NP5B, 9NP5C, 9NP5D 9NP6A, 9NP6B, 9NP6C, 9NP6D 9NP7A, 9NP7B, 9NP7C, 9NP7D 9NP8A, 9NP8B, 9NP8C, 9NP8D 9NP9A, 9NP9B, 9NP9C, 9NP9E 2017 QX60 2018 2/4 ITB20-010 Table 1 (continued) MODEL YEAR CURRENT ECM PART NUMBER: 23710- 2019 3JJ0A, 3JJ1A, 3JJ2A, 3JJ3A, 3JJ4A, 3JJ5A, 3JJ6A 9NM0B, 9NM0D 9NM1B, 9NM1D 9NM2B, 9NM2D 9NM3B, 9NM3D 9NM4B, 9NM4D 9NM5B, 9NM5D 9NM6B, 9NM6D 9NM7B, 9NM7D 9NR0A, 9NR0B, 9NR0E 9NR2A, 9NR2B, 9NR2E 9NR3A, 9NR3B, 9NR3E 9NR4A, 9NR4B, 9NR4E 9NR6A, 9NR6B, 9NR6E 9NR7A, 9NR7B, 9NR7E 9NR8A, 9NR8B, 9NR8E QX60 2020 3JU0B 9NT2B, 9NT4B, 9NT5B, 9NT6B, 9NT8B, 9NT9B 3/4 ITB20-010 Perform the following before starting the reprogramming procedure to prevent damage to the control unit. Connect the AC Adapter to the CONSULT PC. Connect the CONSULT PC to the internet via Wi-Fi or a network cable. Ensure ASIST on the CONSULT PC has been synchronized (updated) to the current date and all C-III plus software updates (if any) have been installed. Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.) within range of the CONSULT PC and the plus VI. If Bluetooth® signal waves are within range of the CONSULT PC or plus VI during reprogramming, the reprogramming may be interrupted. Turn OFF all vehicle electrical loads. Turn ON the hazard warning lamps. Connect a battery maintainer or smart charger, set to reflash mode or a similar setting, to ensure the battery voltage stays between 12.0 V and 15.5 V. HINT: If you are not familiar with the reprogramming procedure, click here. This will link you to the "CONSULTIII plus (C-III plus) ECM Reprogramming" general procedure. Take the vehicle for a 10 minute drive in order to meet the following Idle Air Volume Learning conditions: Engine coolant temperature: 70-100°C (158-212°F) Battery voltage: More than 12.9 V (At idle) Transmission: Warmed up When reprogramming is complete, you will be required to perform Throttle Valve Closed Position, Idle Air Volume Learning, Accelerator Closed Position and DTC erase. 2. Reprogram the ECM. 3. After completing Erase ALL DTCs, print a copy of the C-III plus screen showing the before and after part numbers of the control unit and attach it to the repair order. CLAIMS INFORMATION Submit a Primary Part (PP) type line claim using the following claims coding: DESCRIPTION PFP OP CODE SYM DIA FRT Reprogram the ECM (1) DE97AA ZE 32 (2) (1) Reference the electronic parts catalog and use the ECM part number (23703-*****) as the Primary Failed Part (PFP). (2) Reference the current Infiniti Warranty Flat Rate Manual and use the indicated Flat Rate Time (FRT). AMENDMENT HISTORY PUBLISHED DATE REFERENCE March 20, 2020 ITB20-010 DESCRIPTION Original bulletin published 4/4 ITB20-010