No. 36-16

Installation and Conversion Instructions
Macan (95B)
36/16
ENU
9193
9
Apple CarPlay® Interface incl. Voice Control
Revision:
This bulletin replaces bulletin Group 9, 36/16, dated September 26, 2019.
Work procedures have been revised and content has been updated.
Model Year:
As of 2017 up to 2018
Information:
Retrofitting
Figure 1
Notes:
After enabling the Apple CarPlay® interface in the vehicle, iPhone® apps can also be used in the Porsche
Communication Management (PCM) of the vehicle.
The following requirements must be met in order to use this function:
•
•
At least iPhone® 5 or a newer device with iOS® 7.1 or later software
Availability of Apple CarPlay®
You will find information about the available regions at https://support.apple.com.
Different work must be carried out and/or additional parts must be ordered, depending on vehicle
equipment.
Parts Info:
95B.044.900.07
 License key for Apple CarPlay®
Order the following parts in accordance with vehicle equipment:
Tequipment
May 5, 2020
Page 1 of 12
9
Macan (95B)
9193
ENU
Installation and Conversion Instructions
36/16
Vehicles WITHOUT navigation (I-no. 7Q0):
7PP.035.504.A
1x
GPS antenna
95B.035.550.DD
1x
GPS antenna line
999.513.076.40
10 x
Tie-wrap
955.606.838.00
5x
Tie-wrap with clip
Vehicles WITHOUT Voice control (I-no. QH0).
N .910.207.01
1x
Multiple-tooth screw, M18 x 1.5 x 26
95B.953.50x.x
1x
Steering-column switch (see table)
Installed steering-column switch
Required steering-column switch
Part No.
Part No.
95B.953.502.A
95B.953.502.C
95B.953.502.D
95B.953.502.F
95B.953.502.N
95B.953.502.B
95B.953.502.E
95B.953.502.H
95B.953.502.J
95B.953.502.L
95B.953.502.K
95B.953.502.M
95B.953.502.P
95B.953.502.S
95B.953.502.R
95B.953.502.T
Alternatively, the following instructions will help you to identify the required steering-column switch.
1.
1
Tools:
2.
Look for the standard steering-column switch in the Porsche Electronic Parts Catalogue (PET). To
do this, activate the VIN filter in the PET1 .
Take note of the I-nos.
3.
Replace I-no. QH0 (Without voice control) with I-no. QH1 (Voice control).
If the VIN filter in the PET does not work, the standard steering-column switch must be identified based
on the I-no. in the vehicle information (PIWIS information system).
9900 - PIWIS Tester 3
Nr.32 - Multiple-tooth socket-wrench insert
3438 - Hook
Installing:
May 5, 2020
Page 2 of 12
1
Connect battery charger (  Workshop Manual '2X00IN Battery trickle charging').
2
ONLY for vehicles WITHOUT navigation (I-no. 7Q0):
Install GPS antenna and GPS antenna line
Tequipment
Installation and Conversion Instructions
Macan (95B)
36/16
ENU
9193
9
2.1
Remove PCM display and operator control unit (  Workshop Manual '911019 Removing
and installing PCM display and operator control unit').
2.2
Remove glove compartment (  Workshop Manual '681519 Removing and installing glove
compartment').
2.3
Remove air guide (air duct) at the right (
Figure 2 -1-).
1
2
3
2.4
– Air guide (air duct)
– Internal Torx screw
– Hexagon-head bolt
2.3.1
Unscrew hexagon-head bolt.
2.3.2
Release connector ( Figure 2 -a-)
and disconnect it.
2.3.3
Unscrew internal Torx screw and
remove air guide.
Figure 2
Expose A/B-pillar area (at the right)
2.4.1
Remove (right) A-pillar trim panel (  Workshop Manual '705719 Removing and
installing A-pillar trim panel').
2.4.2
Remove front (right) grab handle (  Workshop Manual '683519 Removing and
installing front grab handle').
2.4.3
Remove rear (right) grab handle (  Workshop Manual '683719 Removing and
installing rear grab handle')
Tequipment
May 5, 2020
Page 3 of 12
9
Macan (95B)
9193
ENU
Installation and Conversion Instructions
36/16
2.4.4
Detach upper part of B-pillar trim
panel (at the right) ( Figure 3
,  Workshop Manual '706719
Removing and installing upper part
of B-pillar trim panel').
1
2.5
– Upper part of B-pillar trim
panel
Expose front roof area
2.5.1
Remove roof console (  Workshop
Manual '708319 Removing and
installing front roof trim panel').
2.5.2
Remove cover over the interior
rear-view mirror (  Workshop
Manual '682719 Removing and
installing interior rear-view mirror')
2.5.3
Figure 3
Remove sun visor at the right and
center bearing (  Workshop Manual '682319 Removing and installing sun visor').
2.5.4
Remove center bearing for sun visor at the left.
2.5.5
Remove screw (2 x) in the roof
console area ( Figure 4 ).
1
– Screw on roof console
Figure 4
Information
Check that the fixing clips are not bent or broken.
Replace missing or damaged fixing clips with new ones.
Make sure that all fastening clips are engaged securely.
May 5, 2020
Page 4 of 12
Tequipment
Installation and Conversion Instructions
Macan (95B)
36/16
ENU
9193
9
Check that they are seated correctly. Check gap and joint dimensions.
2.5.6
ONLY for vehicles with panoramic
roof system:
Unclip roof trim panel at the front
and side areas at the fixing clips
( Figure 5 ).
Figure 5
Information
Make sure that the roof cover does not buckle.
2.5.7
Carefully pull front roof trim panel
down as far as required ( Figure 6
-arrow a-) until the clip is no longer
installed in position (roof) ( Figure
6 -arrow b-).
1
– Clip
Figure 6
Tequipment
May 5, 2020
Page 5 of 12
9
Macan (95B)
9193
ENU
Installation and Conversion Instructions
36/16
2.6
Insert GPS antenna into the holder ( Figure
7 ).
1
2
– GPS antenna holder
– Clip
Press GPS antenna up ( Figure 7 -arrow a-)
until the clips (2 x) lock securely ( Figure 7 ).
2.7
Route GPS antenna line as follows:
GPS antenna → roof console → roof →
A-pillar → behind glove compartment → PCM
installation slot
2.7.1
Figure 7
Connect GPS antenna line
connector to the GPS antenna and move locking mechanism.
Information
Make sure that the roof cover does not buckle.
2.7.2
Route GPS antenna line along
the standard wire harness for the
roof and secure with a tie-wrap
( Figure 8).
1
– GPS antenna line
Figure 8
May 5, 2020
Page 6 of 12
Tequipment
Installation and Conversion Instructions
Macan (95B)
36/16
ENU
9193
9
If there is no standard wire harness,
secure the GPS antenna line to
the roof using a tie-wrap and clip
( Figure 9).
1
2
– Tie-wrap with clip
(955.606.838.00)
– GPS antenna line
Figure 9
2.7.3
Secure GPS antenna line to the
standard wire harness in the A-pillar
with a tie-wrap ( Figure 10 ).
1
– GPS antenna line
Figure 10
Tequipment
May 5, 2020
Page 7 of 12
9
Macan (95B)
9193
ENU
Installation and Conversion Instructions
36/16
2.7.4
Route GPS antenna line from the
A-pillar to the dashboard bracket
( Figure 11 ).
1
2
3
– GPS antenna line
– A-pillar
– Dashboard bracket
Figure 11
2.7.5
ONLY: Vehicles with PCM:
Route GPS antenna line along the
dashboard bracket to the PCM
installation slot ( Figure 12).
1
2
3
– GPS antenna line
– PCM installation slot
– Dashboard bracket
Figure 12
May 5, 2020
Page 8 of 12
Tequipment
Installation and Conversion Instructions
2.7.6
2.8
3
36/16
ENU
9193
9
ONLY for vehicles with radio:
Route GPS antenna line along the
dashboard bracket to the radio
antenna line (same length).
1
2
2.7.7
Macan (95B)
– GPS antenna line
– Radio antenna line
Secure GPS antenna line using
tie-wraps.
Install trim panels in the passenger
compartment in reverse order.
Figure 13
ONLY for vehicles WITHOUT Voice control (I-no. QH0):
Replace steering-column switch.
3.1
Remove steering wheel (  Workshop Manual '481019 Removing and installing steering
wheel').
3.2
Remove trim panel (steering-column switch) (  Workshop Manual '481319 Removing and
installing steering column casing').
3.3
Convert steering-column switch.
3.3.1
Remove steering-column switch (  Workshop Manual '945019 Removing and
installing steering-column switch').
3.3.2
Remove steering wheel electronics control unit from the steering-column switch
and install control unit for steering wheel electronics on the new steering-column
switch (  Workshop Manual '916219 Removing and installing control unit for
steering wheel electronics').
3.3.3
Install steering-column switch.  Workshop Manual '945019 Removing and
installing steering-column switch'
3.4
Install trim panel (steering-column switch) (  Workshop Manual '481319 Removing and
installing steering column casing').
3.5
Install steering wheel (  Workshop Manual '481019 Removing and installing the steering
wheel').
NOTICE
Voltage drop
•
Risk of irreparable damage to control unit
•
Risk of damage to control unit
•
Fault entries in the control unit
•
Coding in the control unit is aborted
Tequipment
May 5, 2020
Page 9 of 12
9
Macan (95B)
9193
ENU
Installation and Conversion Instructions
36/16
•
Malfunctions in control unit, even during programming

Switch off the ignition and remove the ignition key before disconnecting the control unit.

Ensure that the power supply is not interrupted during programming.

Connect a battery charger with a current rating of at least Nominal value 90 A to the vehicle battery.
Information
The 9900 - PIWIS Tester III instructions take precedence since the description may be different
with later Tester releases.
The procedure described here has been structured in general terms; different text or additions may
appear on the 9900 - PIWIS Tester III.
4
Code Apple CarPlay®.
4.1
9900 - PIWIS Tester 3 must be connected and ignition switched on.
4.2
Select "Diagnostics". 9900 - PIWIS Tester 3 detects the model line.
When you press "Next", PIWIS Tester III diagnostics starts.
4.3
Select Additional menu by pressing •F7“. Press •F11“ to confirm the question "Create
vehicle analysis log (VAL)?".
4.4
Enable Apple CarPlay®.
4.4.1
Select the "Function enable" function. Press •F12“ to continue.
Information
PIWIS Tester must be connected to the Porsche Partner Network (PPN) via WLAN
or data cable!
4.4.2
Enter PPN user name. Tap the password input field and enter the password. Select
"Login".
4.4.3
Select the "Enable" function. Press •F12“ to continue.
4.4.4
Touch the license number input field and enter the license number.
Press •F12“ to continue.
4.4.5
Confirm the "Apple CarPlay®" function by pressing •F12“.
Wait until the message "Functions have been enabled successfully." appears.
4.4.6
Press •F12“ to go to the "Overview" menu.
Select the "Display enabled functions" function. Press •F12“ to continue.
Wait until a table containing the enabled functions appears, e.g.:
May 5, 2020
Page 10 of 12
Tequipment
Installation and Conversion Instructions
Control unit
Function
PCM4 (001)
Apple CarPlay®
Macan (95B)
36/16
ENU
9193
9
Status
Voice control
Sport Chrono
Bluetooth
Navigation
UAS (universal audio interface)
4.4.7
Press •F12“ to continue.
Press •F11“ to return to the "Overview" menu.
4.5
Adapt coding.
4.5.1
Press •F11“ to return to the list of control units.
Select all control units by pressing •Ctrl A“. Press •F12“ to continue.
4.5.2
Switch to the "Codings/adaptations" menu. Press •F12“ to continue.
Select "Automatic coding" mode. Press •F12“ to continue.
4.5.3
Wait until the message "Coding has been completed successfully" appears. Press
•F12“ to continue.
Switch to the "Overview" menu.
4.6
Read out the fault memory of all systems, work through any existing faults, and erase the
fault memory (  Workshop Manual '033500 Fault memory for on-board diagnosis').
4.7
Switch off the ignition and disconnect 9900 - PIWIS Tester 3.
4.8
Disconnect the battery charger.  Workshop Manual '2X00IN Battery trickle charging'
91 93 23 40:
–Apple CarPlay® interface enabled–
91 93 23 41:
ONLY for vehicles WITHOUT navigation (I-no. 7Q0):
– Apple CarPlay® Interface enabled –
Includes:
Enabling Apple CarPlay® interface and installing GPS antenna
and GPS antenna line.
Without:
Replacing steering-column switch
Tequipment
Labor time: 77 TU
Labor time: 261 TU
May 5, 2020
Page 11 of 12
9
Macan (95B)
9193
94 50 19 00:
ENU
36/16
Installation and Conversion Instructions
ONLY for vehicles WITHOUT voice control (I-no. QH0):
Steering-column switch removed and installed
Labor time: 58 TU
Important Notice: Technical Bulletins issued by Porsche Cars North America, Inc. are intended only for use by professional automotive technicians who have attended Porsche service training
courses. They are written to inform those technicians of conditions that may occur on some Porsche vehicles, or to provide information that could assist in the proper servicing of a vehicle. Porsche special
tools may be necessary in order to perform certain operations identified in these bulletins. Use of tools and procedures other than those Porsche recommends in these bulletins may be detrimental to the
safe operation of your vehicle, and may endanger the people working on it. Properly trained Porsche technicians have the equipment, tools, safety instructions, and know-how to do the job properly and
safely. Part numbers listed in these bulletins are for reference only. The work procedures updated electronically in the Porsche PIWIS diagnostic and testing device take precedence and, in the event of a
discrepancy, the work procedures in the PIWIS Tester are the ones that must be followed.
© 2020 Porsche Cars North America, Inc.
May 5, 2020
Page 12 of 12
Tequipment