ITB20-022
Service Bulletin Details
Public Details for: ITB20-022
2016-2017 q50; rust on trunk lid above inner rear combination lamp if you confirm client states that corrosion is present on the trunk lid, at or near the rear combination lamps, circled in figure 1. Action 1. Repair the trunk lid
Models from 2017
2017 INFINITI Q50 |
2017 INFINITI Q50 HYBRID |
Models from 2016
2016 INFINITI Q50 |
2016 INFINITI Q50 HYBRID |
Classification: Reference: Date: BT20-010 ITB20-022 September 2, 2020 2016-2017 Q50; RUST ON TRUNK LID ABOVE INNER REAR COMBINATION LAMP APPLIED VEHICLES: 2016-2017 Q50 (V37) 2016-2017 Q50 Hybrid (VH37) APPLIED DATE: Built before April 24, 2017 IF YOU CONFIRM Client states that corrosion is present on the trunk lid, at or near the rear combination lamps, circled in Figure 1. Figure 1 ACTION 1. Repair the trunk lid as needed. 2. Add the rubber spacers and the washers, listed in the PARTS INFORMATION on page 3, to the rear combination lamps. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti retailer to determine if this applies to your vehicle. 1/3 SERVICE PROCEDURE 1. Remove the rear combination lamps from the trunk lid. For the procedure to remove the combination lamps, refer to the Electronic Service Manual (ESM): section DRIVER CONTROLS > EXTERIOR LIGHTING SYSTEM > LED HEADLAMP > REMOVAL AND INSTALLATION > REAR COMBINATION LAMP. 2. Repair the trunk lid finish as needed. 3. Apply one (1) rubber spacer onto the top of each combination lamp in the area shown in Figure 2. See the PARTS INFORMATION on page 3. Rubber spacer Rubber spacer Side view of combination lamp at “A” Figure 2 4. Add two (2) washers to each combination lamp; one (1) to each threaded stud where shown in Figure 3. Place one washer here Place one washer here Figure 3 2/3 ITB20-022 5. Reinstall the rear combination lamps to the trunk lid. For the procedure to reinstall the combination lamps refer, to the Electronic Service Manual (ESM): section DRIVER CONTROLS > EXTERIOR LIGHTING SYSTEM > LED HEADLAMP > REMOVAL AND INSTALLATION > REAR COMBINATION LAMP. PARTS INFORMATION DESCRIPTION PART NUMBER QUANTITY END RUB-RR COMB LAMP (Rubber Spacer) 26553-4GA0A 2 WASHER-PLAIN 08915-4362A 4 CLAIMS INFORMATION Submit a Primary Part (PP) type line claim using the following claims coding: DESCRIPTION PFP OP CODE SYM DIA FRT Install Rubber Spacer and Washers (1) RX6WAA ZA 41 0.5 PFP OP CODE SYM DIA FRT ZA 41 (2) And if needed on the same repair line DESCRIPTION Refinish Trunk Lid-Half Block Repair Preparation & Mixing Time (1) (2) ZL1GAA (1) ZZ99AA Reference the electronic parts catalog and use the Combination Lamp Assy (26550-*****) as the Primary Failed Part (PFP). Reference the current Infiniti Warranty Flat Rate Manual and use the indicated Flat Rate Time (FRT). Expense Code Paint Materials 019 AMENDMENT HISTORY PUBLISHED DATE REFERENCE September 2, 2020 ITB20-022 DESCRIPTION Original bulletin published 3/3 ITB20-022