WRI-20R

ATTENTION:
GENERAL MANAGER
q
PARTS MANAGER
q
CLAIMS PERSONNEL
q
IMPORTANT - All
Service Personnel
Should Read and
Initial in the boxes
provided, right.
SERVICE MANAGER
q
© 2020 Subaru of America, Inc. All rights reserved.
SERVICE PROGRAM BULLETIN
APPLICABILITY:
2020-2021MY Legacy and Outback
NUMBER: WRI-20R
SUBJECT:
		
Reprogramming of Denso CP1 Infotainment 		
Units to Optimize System Performance		
DATE: 12/11/20
REVISED: 12/31/20
INTRODUCTION:
In the interest of customer satisfaction, Subaru of America, Inc. (Subaru) is initiating a Service
Program for certain 2020-2021 model year Legacy and Outback vehicles to update the Cockpit
Control Module (CCM) software to the latest version.
AFFECTED VEHICLES:
Not all vehicles listed below are included in this Service Program. Coverage for all affected
vehicles must be confirmed by using the Vehicle Coverage Inquiry function on subarunet.com. This
information will be available today.
The number of U.S. vehicles included in this service campaign is 212,971.
Model Year
Carline
Affected Units
2020-2021
Legacy
2020-2021
Outback
Refer to Vehicle Coverage Inquiry for WRI-20
Service Program Applicability
DESCRIPTION OF THE REPAIR:
Subaru dealers will reprogram the CCM software on the affected vehicles at no charge for these
customers.
RETAILER RESPONSIBILITY:
Any vehicles listed in any recall/campaign that are in retailer stock must be:
•
Immediately identified
•
Tagged or otherwise marked to prevent their delivery or use prior to repair
•
Repaired in accordance with the repair procedures outlined in the Bulletin
Retailers are to promptly perform the applicable service procedures, to correct all affected vehicles in
their inventory (new, used, demo & SSLP). Additionally, whenever a vehicle subject to this Service
Program is taken into inventory or in for service, necessary steps should be taken to ensure the repair
has been made before selling or releasing the vehicle.
CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD
RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS.
Subaru Service Bulletins are intended for use by professional technicians ONLY. They
are written to inform those technicians of conditions that may occur in some vehicles,
or to provide information that could assist in the proper servicing of the vehicle. Properly
trained technicians have the equipment, tools, safety instructions, and know-how to
do the job correctly and safely. If a condition is described, DO NOT assume that this
Service Bulletin applies to your vehicle, or that your vehicle will have that condition.
Subaru of America, Inc. is
ISO 14001 Compliant
ISO 14001 is the international standard for
excellence in Environmental Management
Systems. Please recycle or dispose of
automotive products in a manner that is friendly
to our environment and in accordance with all
local, state and federal laws and regulations.
Continued...
Bulletin Number: WRI-20R; Revised: 12/31/20
Page 1 of 18
OWNER NOTIFICATION:
Owner notification letters will be mailed in January 2021. Retailers will be notified when owner
notification begins.
SERVICE PROCEDURE:
REMINDER: Customer satisfaction and retention starts with performing quality repairs.
This Campaign affects certain “Mid” and “High” (w/ Navigation) -level CP1 Head Units with 11.6inch display ONLY as pictured below. The “Base” model (2- 7.0-inch display screen unit) is NOT
affected.
MATERIALS REQUIRED:
An empty, USB 2.0 or 3.0 storage device (flash drive) will be needed to perform the update
procedure. The device should be dedicated to storing and transferring these updating files only. It
must be a minimum of 16GB or more in size and contain a NTFS file format before downloading the
update files onto it. Be sure to locate and re-format any existing USB drives used for updating Denso
CP1 audio units to remove any outdated update versions. They must be fully cleared and properly
formatted before adding these new update files to them.
IMPORTANT NOTES:
• NEVER change the update file names after downloading them.
• NEVER save any other files on the same flash drive.
There are various types of USB flash drive available from many suppliers. If the head unit does NOT
recognize the USB drive during the reprogramming process due to controller IC type of USB drive or
compatibility with the Cockpit Control Module (CCM), confirm the flash drive format is NTFS. The
flash drive must be formatted for NTFS. If a recognition problem persists, use a different USB flash
drive from another manufacturer.
Continued...
Bulletin Number: WRI-20R; Revised: 12/31/20
Page 2 of 18
RECOMMENDED USB FLASH DRIVES:
•
Kingston®:
DataTraveler G3 Series, DataTraveler 100 G3 DT100G3, DataTraveler SE9 Series,
DataTraveler SE9 G2 3.0 DTSE9G2 and Digital Data Traveler 3.0 USB Flash Drive - Violet DTIG4
•
SanDisk®:
Ultra Series SDCZ48-064G-J57, Cruzer Blade Series and Cruzer Glide Series CZ60 SDCZ60064G-B35
•
Transcend®:
JetFlash 790 Series TS64GJF790KBE
•
PNY®:
Retract USB 3.0 Flash Drive, black (P-FD64GTRTC-GE)
•
Silicon Power®:
(2 Pack) USB 3.0/3.1 Gen1 USB Flash Drive Blaze
Continued...
Bulletin Number: WRI-20R; Revised: 12/31/20
Page 3 of 18
IMPORTANT NOTE: There are 4 (FOUR) FILES required to complete the update for 2020MY
Legacy and Outback. For 2021MY Legacy and Outback, there are only 3 (THREE) files required.
ALL 4 (or 3) update files MUST BE DOWNLOADED TOGETHER to the USB Flash Drive
before starting the update. PERFORMING THIS UPDATE USING A USB FLASH DRIVE
WITH ANY OF THE REQUIRED UPDATE FILES MISSING WILL LEAD TO A NONRECOVERABLE FAILURE OF THE COCKPIT CONTROL MODULE (CCM) REQUIRING CCM
REPLACEMENT.
ADDITIONAL REPROGRAMMING FILE CONTENT INFORMATION:
In addition to the update for Firmware Over The Air (FOTA) functionality, the following list of other
updates and an enhancement addressed by this reprogramming is supplied below:
•
Clarification of the post-FOTA procedure instructions
required to complete the update. The screenshot below
will appear and explain what must be done to complete
the update installation.
Software Update Installation Complete
To complete the update, your vehicle and STARLINK system must
be fully shut down. Please turn off the engine and exit the vehicle.
Lock doors, and let the vehicle sit for at least 5 minutes. It is recommended to walk at least 10 feet from the vehicle to prevent key
fob interference. After waiting at least 5 minutes, enter the vehicle
and turn the engine on. An “Update Successful” message will appear after a few moments. The update will then be complete.
•
Currently, the microphone level indication is incorrect. The indicator level has been corrected.
More microphone level indication information is included in TSB 15-275-20.
•
A reduced (low) volume (-6db) concern during handsfree conversation when using CarPlay has
been addressed to make the volume level consistent.
•
Voice recognition (VR) has been enhanced to improve recognition of short words (e.g. YES).
•
The program has been corrected to prevent repeated rebooting and system freeze-up immediately
after activation of AndroidAuto.
OPERATIONAL ENHANCEMENT INCLUDED:
The Auto Stop-Start On/Off function button has been moved from the bottom to top layer of the
system for easier use. A screenshot of how the button will appear is shown below.
Continued...
Bulletin Number: WRI-20R; Revised: 12/31/20
Page 4 of 18
STEP 1: Perform a Vehicle Inquiry on Subarunet to confirm WRI-20 applicability. If there is an
OPEN WRI-20 recall, proceed to STEP 2, otherwise this bulletin does not apply.
STEP 2: VERY IMPORTANT: Before proceeding with the software updating procedure, the
currently installed software Version Number MUST be confirmed by following the steps below:
2a) After starting the engine and system boot-up completes, from the HOME screen, touch the 		
Settings button.
2b) Press the General button. Use the down arrow to scroll to System Information then press to 		
display the System Information / Version information.
Continued...
Bulletin Number: WRI-20R; Revised: 12/31/20
Page 5 of 18
The examples below identify the head unit model and the last 6 digits signify the software version
number. Examples:
• F11GHMxxx-xxx (HIGH model software)
• F11GMMxxx-xxx (MID model software)
•
For 2020MY vehicles, if the software version number (xxx-xxx) is 020-501, 020-502, 021-503,
020-704, 021-704 or 022-504, proceed to STEP 4 below. If the software version is 042-380 or
higher, STOP as the module already has the latest software version installed. Proceed to Claim
Reimbursement and Entry Procedures section of the TSB and process a Version Check Only
claim.
•
For 2021MY vehicles, if the software version number (xxx-xxx) is 008-500, proceed to STEP 4
below. If the software version is 040-980 or higher, STOP as the module already has the latest
software version installed. Proceed to Claim Reimbursement and Entry Procedures section of the
TSB and process a Version Check Only claim. NOTE: The Version Number identified MUST be
entered in the Miscellaneous Detail field during claim submission.
STEP 3: Prepare the USB:
CAUTION: Do not use any USB flash drive which utilizes file organizing software or an operating
system.
VERY IMPORTANT: Before attempting to download any data files, confirm the PC and flash drive
being used is not infected with any virus. The flash drive MUST be formatted for NTFS.
•
Make sure the USB flash drive contains no other files.
•
Right click on the corresponding “Removable Disk”.
•
Select “Format”.
•
From the File System drop-down menu, select “NTFS”
•
Check the “Quick Format” box (if not already done).
•
Click on “Start” to format the USB flash drive.
STEP 4: Download the Update Files to the USB.
•
The files are available for download on Subarunet (See “A” below).
•
The applicable reprogramming files have also been sent directly to retailers by Nuspire in the
same way a Select Monitor Update would be pushed out. (See “B” below).
Continued...
Bulletin Number: WRI-20R; Revised: 12/31/20
Page 6 of 18
Follow “A” below when using files downloaded from Subarunet. Subarunet Links Page screenshot:
A:
IMPORTANT: Files downloaded from Subarunet will be .zip files and must be unzipped before
they can be used. Using the normal audio / navigation system file update download procedure: Go to
Subarunet, select Service Operations and Technical>>Forms/Downloads>>Gen 4/Denso for Audio/
Navi then click on the applicable Hyperlink to download the file(s) to your SDS Notebook or PC:
MID-20-Legacy-Outback-Denso-CP1 AUDIO UPDATE-DECEMBER 2020
HIGH-20-Legacy-Outback-Denso-CP1 AUDIO UPDATE-DECEMBER 2020
MID-21-Legacy-Outback-Denso-CP1 AUDIO UPDATE-DECEMBER 2020
HIGH-21Legacy-Outback-Denso-CP1 AUDIO UPDATE-DECEMBER 2020
REMINDER: Although BASE models are listed on the Links Page, this WRI-20 Campaign is
applicable to “MID” and “HIGH” (Navigation-equipped) units ONLY.
•
Go to Downloads.
•
CAUTION: After download is complete, NEVER change the file or folder names.
•
Open / display the contents of File folder, for example: “Version4(RC2011dash)_F11GHM042380(High).zip”.
•
Click on “Extract All Files”
Continued...
Bulletin Number: WRI-20R; Revised: 12/31/20
Page 7 of 18
•
The screen below will appear to set a destination for the extracted file.
•
Double-click on the required folder (for this example, select the file entitled
“Version4(RC2011dash)_F11GHM042-380(High)”)
•
This will display all 4 (four) files inside the folder
•
Select and copy all 4 (four) files then paste (or click / drag) them into the “clean” USB flash drive
as listed (Removable Disk) in the directory.
IMPORTANT NOTE: There are 4 (FOUR) FILES required to complete the update for 2020MY
Legacy and Outback. For 2021MY Legacy and Outback, there are only 3 (THREE) files required.
ALL 4 (or 3) update files MUST BE DOWNLOADED TOGETHER to the USB Flash Drive
before starting the update. PERFORMING THIS UPDATE USING A USB FLASH DRIVE
WITH ANY OF THE REQUIRED UPDATE FILES MISSING WILL LEAD TO A NONRECOVERABLE FAILURE OF THE COCKPIT CONTROL MODULE (CCM) REQUIRING CCM
REPLACEMENT.
Continued...
Bulletin Number: WRI-20R; Revised: 12/31/20
Page 8 of 18
•
To avoid confusion, use a permanent marker to label the flash drive with the file contents (e.g.
MID Denso CP1 WRI-20, or HIGH Denso CP1 WRI-20).
•
Go to STEP 5:
Follow “B” below when using the files sent directly to the SDS notebook from Nuspire.
B:
•
Go to My Documents on the GUI screen click on the folder “Denso CP1 Audio-Navi Update
Files” to display the list of available update files shown below. IMPORTANT: Always confirm
there are two folders as shown below, “2020” and “2021”. If not, the SDS notebook hasn’t been
updated with the latest release. Please contact Nuspire to request they resend the update.
•
Double-click on the required folder (for this example, select the file entitled “HIGH”) and the
update file will display as shown below.
•
Select all files and either copy / paste or click / drag them to the USB flash drive.
CAUTION: NEVER change the file names.
•
Once all files have been loaded onto the USB flash drive, right click on the drive and select
“Eject”.
•
Remove the USB flash drive after the prompt appears that says, “Safe to Remove Hardware”.
Continued...
Bulletin Number: WRI-20R; Revised: 12/31/20
Page 9 of 18
•
Mark the USB to indicate the head unit it will update (MID Denso CP1 WRI in this example).
•
Repeat the above steps to create the MID Denso CP1 WRI or HIGH Denso CP1 WRI USB flash
drives as needed using a separate USB drive for each update folder.
•
Proceed to STEP 5 below.
STEP 5:
Perform the software update.
CAUTIONS:
• NEVER attempt to install the software immediately following an exchange unit installation. Let
the system restart first and operate for 20 minutes.
• NEVER attempt to install the software a second time for 30 minutes following a previously
unsuccessful software installation.
•
NEVER attempt to install the software for at least 30 minutes after completing a FOTA update.
5a) Perform the update in a well-ventilated location if updating with the engine running OR with
the ignition ON and the DCA battery charger connected in Power Supply mode.
5b) PRESS and HOLD the RIGHT-side temperature control buttons
(both up and down), press the Tune / Scroll knob 6 times then release
all to display the Dealership Mode Menu.
5c) Select Software Update from the Dealership Mode menu.
Continued...
Bulletin Number: WRI-20R; Revised: 12/31/20
Page 10 of 18
IMPORTANT NOTE: On a RARE occasion, the message “Software update setup is initializing…”
may be displayed. Should this occur, proceed to “Appendix A” at the end of this bulletin for further
instruction. For critical Service Bulletin helpful tips to prevent unnecessary hardware replacement,
follow the link to an important Subarunet message: https://www.subarunet.com/home/ home.html#/
Announcement/83194.
5d) The screen shown here will be displayed.
5e) Insert the H/U reprogramming USB into the USB port. When the update screen appears,
confirm the message on it and if no concerns, press OK.
		
NOTE: If after plugging in the USB, the screen displays a Software Loading Unsuccessful message,
confirm the USB device has been properly formatted and the software on the device matches the H/U
being reprogrammed (example: MID software is being used to update a MID H/U).
5f) The screen below will be displayed. NOTE: The actual software version displayed will be 		
different from the EXAMPLE picture shown below.
Continued...
Bulletin Number: WRI-20R; Revised: 12/31/20
Page 11 of 18
See the
IMPORTANT:
message below.
IMPORTANT: The example above identifies the head unit model and the last 6 digits signify the
software version number. Examples:
• F11GHMxxx-xxx (HIGH model software)
• F11GMMxxx-xxx (MID model software)
Software Version Table
2020MY
2021MY
•
Press OK to start the software update.
Continued...
Bulletin Number: WRI-20R; Revised: 12/31/20
Page 12 of 18
5g) Once the update begins, the screen below will be displayed with a progress bar. It takes 		
about 15 to 20 minutes for the update to complete.
VERY IMPORTANT: NEVER turn the ignition OFF or ON while the software update is in process.
To avoid any concerns with battery condition during programming, always perform the update with
either the engine running (outside or with an exhaust hose attached) or with the DCA charger attached
and in power supply mode.
5h) When the update is complete, the screen below will be displayed (the actual software version
number will be different).
IMPORTANT NOTE: On rare occasions a “Software Update Incomplete” message may appear
in this step which occurs due to a bug in the software update procedure. DO NOT attempt to install
the update again, proceed to 5i) below to confirm the software version has been updated to the latest
version.
5i) Select OK in the screen above then remove the H/U reprogramming USB from the USB port.
Continued...
Bulletin Number: WRI-20R; Revised: 12/31/20
Page 13 of 18
5j) Turn the Ignition OFF, open the driver’s door then close the driver’s door.
5k) Wait for at least 3 minutes, then turn the ignition ON.
5l) Access Dealership Mode following steps provided STEP 2 above and confirm the software 		
update completed successfully using the table below. . Always record the new software 		
version number on the RO.
2020 and 2021 MY Post-Update Version Number Tables
5m) Turn the ignition OFF, open the driver’s door then close the driver’s door to complete the 		
update procedure.
VERY IMPORTANT: After the CCM reprogramming procedure is complete, ALWAYS confirm
proper back-up camera operation before releasing the vehicle.
SERVICE PROGRAM IDENTIFICATION LABEL:
Type or print the necessary information on a Campaign Identification Label. The completed label
should be attached to the vehicle’s upper radiator support. Additional labels are available through
normal parts ordering channels. The part number is MSA6P1302, which comes as one sheet of 20
labels.
WRI-20
Continued...
Bulletin Number: WRI-20R; Revised: 12/31/20
Page 14 of 18
CLAIM REIMBURSEMENT AND ENTRY PROCEDURES:
Credit to perform this recall will be based on properly completed repair order information. Retailers
may submit claims through Subarunet.com.
Labor Description
Labor
Operation #
Labor
Time
WRI-20- SOFTWARE VERSION CHECK ONLY
A131-138
0.2
WRI-20- SOFTWARE UPDATE / REPROGRAMMING
A131-118
0.6
Fail Code
WRI-20
A ONE-TIME charge of $30.00 can be claimed in sublet to cover the cost of the USB flash drives.
IMPORTANT REMINDERS:
•
SOA strongly discourages the printing and/or local storage of service information as previously
released information and electronic publications may be updated at any time.
•
Always check for any open recalls or campaigns anytime a vehicle is in for servicing.
•
Always refer to STIS for the latest service information before performing any repairs.
Continued...
Bulletin Number: WRI-20R; Revised: 12/31/20
Page 15 of 18
Continued...
Bulletin Number: WRI-20R; Revised: 12/31/20
Page 16 of 18
This notice applies to the VIN identified in
the address section printed below
Subaru Service Program WRI-20
January 2021
Dear Subaru Owner:
We would like to thank you for your selection of a Subaru vehicle. We take pride in our products and are committed to your continued satisfaction.
Subaru of America, Inc. (Subaru) is initiating a service program for certain 2020-2021 model year Legacy and
Outback vehicles to update the Cockpit Control Module (CCM) software to the latest version. Our records indicate that you currently own one of these vehicles.
REASON FOR THIS SERVICE PROGRAM
The latest version of the CCM software includes an update for the firmware-over-the-air (FOTA) functionality,
updates related to the microphone and volume level functionality, an update related to the voice recognition
functionality, and an update to prevent repeated rebooting after activating Android Auto.
WHAT SUBARU WILL DO
In the interest of your continued satisfaction Subaru will reprogram the CCM in your vehicle at no cost to you.
WHAT YOU SHOULD DO
Please contact your Subaru retailer (dealer) for an appointment to have this repair performed at no cost to you.
HOW LONG WILL THE REPAIR TAKE?
The actual time to perform this repair is less than 40 minutes. However, it may be necessary to leave your vehicle
for a longer period of time on the day of your scheduled appointment to allow your Subaru retailer flexibility in
scheduling.
CHANGED YOUR ADDRESS OR SOLD YOUR SUBARU?
If you have moved or sold your vehicle, please update this information online at www.subaru.com, select ‘Customer Support,’ then select ‘Address Update’ or ‘Ownership Update’ from the drop-down menu.
IF YOU HAVE PREVIOUSLY PAID FOR A REPAIR
If you have already paid for repairs associated with this coverage, you may be eligible for reimbursement. Reimbursement consideration will be based on the amount an authorized Subaru retailer in your area would charge
for the same repair.
Continued...
Bulletin Number: WRI-20R; Revised: 12/31/20
Page 17 of 18
Please send the original service repair order, which has the name of the repair facility, date of repair, mileage at
the time of repair, complete 17-digit vehicle identification number (VIN), and your name, with correct mailing address and telephone number to the address listed below.
Subaru of America, Inc.
Customer Advocacy Department, Attention: WRI-20 Service Program
P.O. Box 9103, Camden, NJ 08101-9877
Please send original receipts only and retain a photocopy for your records. Please be assured that we will attempt to process your reimbursement request as quickly as possible, but it may take up to 60 days for this
process to be completed.
IF YOU NEED FURTHER ASSISTANCE:
To locate the nearest Subaru retailer, you can access our website at www.subaru.com and select ‘Find a Retailer.’
For additional information, please go to: http://www.wri20.service-campaign.com.
If you need additional assistance, please contact us directly:
• By e-mail: Go to www.subaru.com and select “Contact Us”
• By telephone: 1-844-373-6614
Monday through Friday between 8:00 a.m. and 7:00 p.m. ET
• By U.S. Postal mail: Write us at Subaru of America, Inc.
Attn: Customer Advocacy Department
P.O. Box 9103, Camden, NJ 08101-9877
Please contact us immediately if the Subaru retailer fails or is unable to make the necessary repairs free of
charge.
Your continued satisfaction with your Subaru is important to us. Please understand that we have taken this action in the interest of your vehicle’s proper operation. We sincerely apologize for any inconvenience this matter
may cause and urge you to schedule an appointment as soon possible.
Sincerely,
Subaru of America, Inc.
A subsidiary of SUBARU CORPORATION
Bulletin Number: WRI-20R; Revised: 12/31/20
Page 18 of 18