JTB00585NAS3

12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
JTB00585NAS3
TECHNICAL BULLETIN
16 DEC 2020
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional
Technicians with the knowledge, tools, and equipment required to do the job properly and
safely. It informs these Technicians of conditions that may occur on some vehicles, or
provides information that could assist in proper vehicle service. The procedures should not
be performed by 'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition
described affects your vehicle. Contact an authorized Jaguar service facility to determine
whether this bulletin applies to a specific vehicle.
INFORMATION
This reissue replaces all previous versions. Please destroy all previous versions.
This bulletin supersedes TSB JTB00585NAS2/2018 dated 12 FEB 2018, which should either
be destroyed or clearly marked to show it is no longer valid (e.g. with a line across the page).
Only refer to the electronic version of this Technical Bulletin in TOPIx.
Changes are highlighted in blue
SECTION:
418-02
SUBJECT/CONCERN:
Passive Entry System Slow To Unlock
AFFECTED VEHICLE RANGE:
MODEL:
XF (X260)
MODEL YEAR:
2018
VIN:
Y53259-Y53224
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
ASSEMBLY PLANT:
Castle Bromwich
1/15
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
MARKETS:
NORTH AMERICA
CONDITION SUMMARY:
NOTE:
This bulletin affects XF models that feature passive entry without the soft close
function.
SITUATION:
The fast latch operation does not operate and there is a delay upon entry to the vehicle
using passive entry.
CAUSE:
Wiring harness design error for 2018 model year passive entry (without soft close) vehicles
only.
ACTION:
Follow the instructions below.
PARTS:
NOTES:
Repair wires, heatshrink sleeves, and splice connectors can be obtained from the
wiring harness repair kit or ordered through your parts department.
Repair wires, heatshrink sleeves, and splice connectors are supplied in packs of 10.
PART NUMBER
DESCRIPTION
QUANTITY
418279
Repair wire
4
418104
Heatshrink sleeve
4
418107
Splice connector
4
T4N9812
Door trim panel clip
38
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
2/15
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
TOOLS:

418-672
Insulation (Wire) Stripper

418-116A
Wire crimper
WARRANTY:
NOTES:
Repair procedures are under constant review, and therefore times are subject to
change; those quoted here must be taken as guidance only. Use TOPIx to obtain
the latest repair time.
The JLR claims submission system requires the use of causal part numbers. Labor
only claims must show the causal part number with a quantity of zero.
DESCRIPTION
SRO
TIME (HOURS)
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
CONDITION CODE
CAUSAL PART
3/15
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
DESCRIPTION
Passive entry - Wiring
modification
SRO
TIME (HOURS)
CONDITION CODE
CAUSAL PART
76.96.59
2.6
JU
T2H27766
NOTE:
Normal Warranty procedures apply.
SERVICE INFORMATION:
1.
See TOPIx Workshop Manual section 418-02: Wiring harnesses - General
procedures - Wiring harness repair for information on the repair or modification of
electrical wiring harnesses.
SERVICE INSTRUCTION 'A' - FRONT RIGHT DOOR
NOTES:
Some variation in the illustrations may occur, but the essential information is always
correct.
Removal steps in this procedure may contain installation details.
Some components shown removed for clarity.
1.
Remove the front right door trim panel (see TOPIx Workshop Manual section 501-05:
Interior trim and ornamentation - Removal and installation - Front door trim panel).
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
4/15
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
2.

Disconnect the front right door electrical wiring harness and position to the side.
3.

Remove the door window regulator retaining clip.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
5/15
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
4.

Remove the front right door closing panel.
5.

Disconnect the front right door electrical wiring harness from the front right door
latch.
Withdraw the electrical wiring harness from the front right door so it can
be modified.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
6/15
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
6.

Remove the fir tree clip from the front right door electrical wiring harness.
Remove the insulation tape from the front right door electrical wiring
harness up to the retaining clip (1).
7.

Locate electrical connector C6PK10 on the front right door electrical wiring harness
and remove the sealing grommet from cavity 2.
1. Install the repair wire into cavity 2.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
7/15
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
8.

Install the repair wire to the front right door electrical wiring harness with electrical
insulation tape as shown.
1. Route the repair wire through the front right door electrical wiring loom
retaining clip.
9.

Locate the electrical connector C6PL64.
1. Locate the electrical wire in cavity 5.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
8/15
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
10.

Cut the electrical wire 150 mm from the back of the electrical connector C6PL64.
11.
NOTE:
Do not apply heat to the heatshrink at this stage.

Install a length of heatshrink onto the front right door electrical wiring harness.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
9/15
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
12.

Cut the repair wire to a suitable length and prepare the front right door electrical
wiring harness for a splice connector.
13.

Create a 2-wire splice joint between the front right door electrical wiring harness
and the repair wire.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
10/15
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
14.
WARNING:
When using a heat source, make sure that it is localized and does not cause
damage to the operator or surrounding materials.

Position the heatshrink over the splice connector and apply heat to seal the splice
connector.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
11/15
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
15.

Install the fir tree clip 80 mm from the connector C6PL64 on the front right door
electrical wiring harness.
1. Wrap the front right door electrical wiring harness with insulation tape.
16.

Make sure there is 50 mm clearance between the electrical connector C6PL64 and
the insulation tape.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
12/15
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
17.

When installing the front right door closing panel, make sure to pass the door
window regulator retaining clip through the door closing panel as shown.
18.

Install the front right door closing panel.
Torque: 2 Nm.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
13/15
12/16/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
19.

Install the door window regulator retaining clip.
20.
To install, reverse the removal procedure.
SERVICE INSTRUCTION 'B' - FRONT LEFT DOOR
1.
Perform Service Instruction 'A' with the following changes.
1. The connectors on the front left door electrical wiring harness are C5PK09 and
C5PL63.
2. Install the repair wire into cavity 5 of electrical connector C5PK09
3. Create a splice joint between the repair wire and the wiring in cavity 4 of
C5PL63 on the front left door electrical wiring harness.
SERVICE INSTRUCTION 'C' - REAR RIGHT DOOR
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
14/15
12/16/2020
1.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
Perform Service Instruction 'A' with the following changes.
1. The connectors on the rear right door electrical wiring harness are C8PK12 and
C8PL72.
2. Install the repair wire into cavity 2 of electrical connector C8PK12.
3. Create a splice joint between the repair wire and the wiring in cavity 5 of
C8PL72 on the rear right door electrical wiring harness.
SERVICE INSTRUCTION 'D' - REAR LEFT DOOR
1.
Perform Service Instruction 'A' with the following changes.
1. The connectors on the rear left door electrical wiring harness are C7PK11 and
C7PL72.
2. Install the repair wire into cavity 5 of electrical connector C7PK11.
3. Create a splice joint between the repair wire and the wiring in cavity 4 of
C7PL72 on the rear left door electrical wiring harness.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1608124072212
15/15