V0121032061990_1
Service Bulletin Details
Public Details for: V0121032061990_1
Current engine/motor control module -j623- software can lead to various fault codes within the vehicle.
- 2019 -
Models from 2019
2019 VOLKSWAGEN GOLF |
2019 VOLKSWAGEN GOLF SPORTWAGEN |
Technical Service Bulletin 01-21-03 - Various Engine/Motor Control Module -J623- Software Updates Transaction No: 2061990/1 Release date: 2/4/21 Condition Applicable Vehicles Model(s) Year Eng. Code Trans. Code VIN Range From VIN Range To Golf SportWagen 2019 1.4L All All All Golf 2019 All All All (DGXA) 1.4L (DGXA) Revision Table Instance Number Published Date Version Number 2061990/1 01/4/21 01-21-03 Reason For Update Original publication. Tip: This software update also includes modification for: P2181, P0410, P0491, P0133, P0135 and P0111 DTCs. One or more of the following fault codes may be stored in the Engine Control Module (ECM) Fault Memory: DTC Description P2181 Cooling System Performance P0410 Sec.Air Inj.Sys. Malfunction P0491 Secondary Air Injection System (Bank 1) insufficient flow P0133 O2 Sensor Circ.,Bank1-Sensor1 Slow Response P0135 O2 Sensor Heater Circ.,Bank1-Sensor1 Malfunction P0111* Intake Air Temperature Sensor 1 Bank 1 Circuit Range/Performance Page 1 of 6 plus attachment © 2021 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Transaction No: 2061990/1 Release date: 2/4/21 Technical Service Bulletin 01-21-03 - Various Engine/Motor Control Module -J623- Software Updates Note: DO NOT diagnose or replace components due to P2181, P0410, P0491, P0133, P0135 and P0111* faults before performing the update function as explained in this bulletin. Note: *If the vehicle has fault code P0111, additional steps are required below. Technical Background Current Engine/Motor Control Module -J623- software can lead to various fault codes within the vehicle. This technical bulletin requires an additional step if P0111 is stored in the ECM, details below. Production Solution Improved Engine/Motor Control Module -J623- software. Service Update-Programming Procedure: Critical Warning: : The Midtronics battery charger must be connected to the vehicle battery for the duration of the programming, to ensure the battery state of charge remains above 12.5 volts during the update process. If the battery drops below 12.5 volts, the programming could fail which may result in damage to the control module. Control modules damaged by inadequate voltage will not be covered under the warranty policy. The technician should verify the vehicle voltage prior to starting the update process, and should monitor the voltage for the duration of the update. WARNING: Radiator Fan(s) may cycle ON high speed during the Update Process! There is a risk that personal injury may result if contact is made with spinning fan blades. Keep hands and all objects away from Radiator Fan(s) during Update Process! Page 2 of 6 plus attachment © 2021 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin 01-21-03 - Various Engine/Motor Control Module -J623- Software Updates Transaction No: 2061990/1 Release date: 2/4/21 Note: Prior to launching the ODIS Service diagnostic applications and starting control module update process, confirm tester screen saver and power settings in accordance with Diagnostic Device Hardware & Windows® - VHW-20-02 Change Power Options After Windows®10 Upgrade. Failure to do so may result in the tester entering power save mode during data transfer, and subsequent control module failure. When using a VAS 6150/X or 6160/X tester in conjunction with a VAS 6154 wireless transmitter head for a flash procedure, connect a USB cable between the transmitter head and the tester. Failure to do so may lead to errors during the flash procedure. VAS tools must only be used with their power adapters plugged in. Under no circumstances should they be used on battery power alone during the programming procedure. Tip: To Update-Programming using Software Version Management (SVM), review and follow instructions in Technical Bulletin Instance 2014603 “Software Version Management”. The SVM process must be completed in its entirety so the database receives the update confirmation response. A warranty claim may not be reimbursed if there is no confirmation response to support the claim or action is carried out that is not explicitly stated in the Technical Bulletin. Update the Engine Control Module using the SVM Unit code as listed in the table below: Model Engine Old Software Part No. Old Software Version New Software Part No. New Software Version (or higher) SVM Unit Code Golf DGXA 04E 906 024 S 5804 04E 906 024 S 9970 456C SportWagen 6130 6547 6655 6814 6999 7297 7467 9908 04E 906 024 K 4204 04E 906 024 K Page 3 of 6 plus attachment © 2021 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin 01-21-03 - Various Engine/Motor Control Module -J623- Software Updates Transaction No: 2061990/1 Release date: 2/4/21 4393 4401 6129 6545 6652 6811 6998 7296 7466 9904 Tip: The procedure can be found in GFF under Functions/ Component Selection, Software Version Management, Adapting Software. Ensure attached ECM/TCM Tuning Form has been completed and signed by customer as required in SVM Technical Bulletin Instance 2014603. If P0111 was stored in the ECM, and after updating the ECM software, install a hood silencer onto the vehicle according to ELSA instructions. Page 4 of 6 plus attachment © 2021 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin 01-21-03 - Various Engine/Motor Control Module -J623- Software Updates Transaction No: 2061990/1 Release date: 2/4/21 Warranty To determine if this procedure is covered under Warranty, always refer to the Warranty Policies and Procedures Manual 1) Model(s) Year(s) Eng. Code(s) Golf SportWagen 2019 1.4L Trans. Code(s) VIN Range From VIN Range To All All All All All All (DGXA) Golf 2019 1.4L (DGXA) SAGA Coding Claim Type: Use applicable Claim Type 1) Service Number: Damage Code 2470 0039 HST Damage Location (Depends on Service No.) - - Golf, Golf SportWagen Parts Manufacturer 3ME 2) Labor Operation 3) : Charge Battery 27068950 = see ELSA for latest time units. Labor Operation 3) : Update Programming ECM Control Module 24705599 = 50 TU Labor Operation 3) : Install Hood Silencer (only required for P0111 fault code) 70041999 = 10 TU Causal Part: 27068950 Diagnostic Time 4) GFF Time expenditure 01500000 = Actual GFF print out NO Road Test 01210004 = 10 TU YES Technical Diagnosis 01320000 = 00 TU max. NO Claim Comment: Input “As per Technical Bulletin 2061990” in comment section of Warranty Claim. Page 5 of 6 plus attachment © 2021 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin 01-21-03 - Various Engine/Motor Control Module -J623- Software Updates Transaction No: 2061990/1 Release date: 2/4/21 1) Vehicle may be outside any Warranty in which case this Technical Bulletin is informational only. 2) Code per warranty vendor code policy. 3) Labor Time Units (TUs) are subject to change with ELSA updates. 4) Documentation required per Warranty Policies and Procedures Manual. Required Parts and Tools Note: * Part only required if P0111 was stored in the ECM. Part No: Part Description Quantity 5GM-863-831* Hood Silencer 1 Part numbers are accurate at time of publication. Always refer to ETKA for the latest part information. Tool Description Tool No: Midtronics Battery Tester/Charger GRX3000VAS or MTRMSP0702 battery maintainer/charger VAS Diagnostic Tool VAS 6150/X & VAS 6160/X and ODIS Service with current online updates Additional Information All part and service references provided in this Technical Bulletin are subject to change and/or removal. Always check with your Parts Dept. and Repair Manuals for the latest information. Page 6 of 6 plus attachment © 2021 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. OWNER INFORMATION ABOUT CONTROL MODULE TUNING* ACKNOWLEDGEMENT AND AUTHORIZATION FOR REPROGRAMMING (REFLASHING) OF CONTROL MODULE(S) *) “TUNING” is described as the addition of or modification of any component which causes a Volkswagen vehicle to perform outside the normal parameters and specifications approved by Volkswagen Group of America / Volkswagen Group Canada. Date: Dealer Number: Vehicle Identification Number: Repair Order Number: Dealer stamp I , owner or driver of the above identified Volkswagen, confirm: - “Tuning” as described above (especially power increasing modifications) has NOT been performed on my vehicle. - “Tuning” as described above has been performed on my vehicle and the following components were modified or installed: TUNING was performed by (Please provide Company name and telephone number, if you wish us to contact them): I understand that if my Control Module is determined to have been tuned, any damage caused by the tuning of the Control Module (including adverse emissions consequences) will not be covered by VWGoA / VGC warranties. I am permitting an authorized Volkswagen Dealer to reflash (update) my Control Module, and by doing so, I understand that this process will automatically overwrite (destroy) and permanently delete any tuning program that was previously installed on the Control Module of my Volkswagen vehicle. By signing below, I fully acknowledge and understand that the tuning program will not be restored and VWGoA / VGC, will not be liable in any way for the loss of tuning data. Signature of Customer E 2021 Volkswagen Group of America Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and intellectual property rights of VGoA / VGCA Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or other by any means, .electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.