22TechRefGde221

2022
Pre-Delivery Inspection
Technician Reference Document
Effective 2-26-2021-US
Version 1.0
Table of Contents
Technician Reference Document
Technician Reference Document Overview
The Pre-Delivery Inspection Technician Reference Document is designed to be a resource used in hand with
the Pre-Delivery Inspection Checklist (PDI). The PDI Checklist has been simplified to make the process more
efficient, and in doing so, this document has been created to be used as a reference for checklist items that
may have additional information. On the PDI Checklist, you find that certain items have been notated with an
asterisk symbol (*), this lets you know that additional information can be found in this Technician Reference
Document.
Below you will find a list of each model, with the page numbers to their left. After navigating to the desired
page, you will notice each model page is formatted similarly to the PDI Checklists. After each section title is the
original checklist item, followed by any additional information specific to that model.
Table of Contents
3-4
e-tron
Effective 2-26-2021-US
Version 1.0
Model Year 2022 | Audi Pre-Delivery Reference Document | 2
e-tron/Sportback/GT
Technician Reference Document
Vehicle Preparation
Trunk Inspection
•      Perform any open campaigns
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Follow instructions listed in campaign documentation
•      Perform diagnostic work
Connect vehicle diagnostic tester
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Select “Diagnosis” mode and start diagnosis
Interior
•      Perform vehicle identification
•      Check operation of window, lock, and seat controls
•      Untick “Working with Guided Fault Finding”
•      Switch to “Special functions” tab and select following
program:
Delivery Inspection total
•      Start program by selecting “Carry out check”
•      Continue to follow instructions on screen and complete
the process
•      Switch to the “Control units” tab, press the “Guided Fault
Finding” button and launch Guided Fault Finding as far
as the test plan
•      The static event memory entries must be evaluated and,
if necessary, processed using Guided Fault Finding
•      Exit diagnosis; diagnostic log for delivery inspection is
sent automatically
•      Install front license plate carrier (if necessary)
•      Retain any removed trim required for carrier installation
and give to the customer. If no front license plate carrier
is necessary ensure the carrier remains in the trunk for
the customer
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
•      Check all doors for proper power closing
For vehicles equipped with the power door closing feature,
check all doors for proper closing
Lighting and Windshield
•      Test front washers (and headlight washers if equipped).
Correct aim if necessary
Headlights must be on to test functionality of the headlight
washers
Effective 2-26-2021-US
Version 1.0
Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Verify operation of heated/ventilated and massaging seats
(front/rear) (if equipped)
Check both front and rear. Massaging feature is in the front
seats only (if equipped)
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling, open all panel vents
for all zones
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation (if
equipped)
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on”
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Setup/Settings menu:
Home > Settings > General > Measurement Units >
Consumption (electric motor) to mi/kWh, and check to ensure all other units are set to US specs
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands
•      Set “Music volume while parking” to medium
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
Model Year 2022 | Audi Pre-Delivery Reference Document | 3
e-tron/Sportback/GT
Technician Reference Document
Settings (continued)
Driver Assistance
•      Set dealership location in navigation (if equipped)
•      Verify operation of parking system
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning (if equipped)
This can be changed in the Driver Assistance Settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual > Select Off
•      Disable climate control via door unlock
Main screen => Vehicle => Climate control => select small
temperature gauge symbol in upper right section => settings
(“wheel” upper right) => unselect (disable) “Start A/C after
unlocking”. Check and adjust, if needed. Button position
“off”, in left position
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
•      Verify all vehicle Head-up display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
Audi connect® (USA ONLY) (if equipped)
•      Turn on the Wi-Fi® hotspot (if equipped)
Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” )
•      Check Wi-Fi® hotspot visibility. No data available at PDI
due to dealer demo mode
Check Wi-Fi® hotspot functionality is enabled and verify the
Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX
is the last four digits of the VIN. Via Telephone > Options >
Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings
> Access point (SSID)
•      Enable satellite map view for navigation
Enable satellite map view in the Navigation > Gear icon >
Map Settings, and verify the satellite imagery appears in the
navigation map screen
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure
Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door
jamb, and store tire pressure values in Car/System menu
Driving Performance
•      Verify electric motor performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Effective 2-26-2021-US
Version 1.0
Model Year 2022 | Audi Pre-Delivery Reference Document | 4