T-SB-0043-20 Rev

Service Bulletin Details

Public Details for: T-SB-0043-20 Rev

Tsb: some 2016 ? 2020 model year tacoma vehicles equipped with a 2gr-fks engine and a manual transmission may exhibit a mil on condition with diagnostic trouble code (dtc) P211904 (ecm/pcm throttle actuator ?A? Control throttle body range/p


- 2020 - 2019 - 2018 - 2017 - 2016 -

Models from 2020
2020 TOYOTA TACOMA
Models from 2019
2019 TOYOTA TACOMA
Models from 2018
2018 TOYOTA TACOMA
Models from 2017
2017 TOYOTA TACOMA
Models from 2016
2016 TOYOTA TACOMA
T-SB-0043-20
Rev1
April 21, 2020
MIL ON With DTC P211904 - 2GR-FKS (6MT)
Service
Category
Vehicle Interior
Section
Meter/Gauge/Display
Market USA
Applicability
YEAR(S)
MODEL(S)
2016 - 2020
Tacoma
ADDITIONAL INFORMATION
REVISION NOTICE
February 12, 2021 Rev1:
 Applicability has been updated to include 2018 – 2020 model year Tacoma vehicles.
 The Warranty, Parts Information, and Calibration Information sections have been updated.
Any previous printed versions of this bulletin should be discarded.
Introduction
Some 2016 – 2020 model year Tacoma vehicles equipped with a 2GR-FKS engine and a manual
transmission may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P211904
(ECM/PCM Throttle Actuator “A” Control Throttle Body Range/Performance System Internal
Failure) with vehicle entering limp mode. The Engine Control Module (ECM) (SAE term:
Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this
condition. Follow the Repair Procedure in this bulletin to address this condition.
Warranty Information
OP
CODE
DESCRIPTION
TIME
MODEL
NAME
MODEL
YEAR
TRANSMISSION
OFP
T1
T2
800269
Engine ECM
Reprogramming
(Per FRM)
0.7
Tacoma
2016
–
2020
M/T
89661-#####*
8A
74
*Choose the correct OFP for the vehicle being repaired by searching for the parts in the EPC using the EPC VIN filter.
Warranty Claims MUST be submitted with the correct 10-digit OFP.
APPLICABLE WARRANTY
 This repair is covered under the Toyota Federal Emission Warranty. This warranty is in effect
for 96 months or 80,000 miles, whichever occurs first, from the vehicle’s in-service date.
 Warranty application is limited to occurrence of the specified condition described in
this bulletin.
© 2021 Toyota Motor Sales, USA
Page 1 of 6
T-SB-0043-20
Rev1
April 21, 2020
Page 2 of 6
MIL ON With DTC P211904 - 2GR-FKS (6MT)
Parts Information
PART NUMBER
MODEL
MODEL YEAR TRANSMISSION
PART NAME
PREVIOUS
89661-04K63
89661-04K62
89661-04K64
89661-04K61
89661-04K60
2016 – 2017
2018
Tacoma
M/T
89661-04K31
89661-04K32
89661-04K30
Computer, Engine Control (ECM)
2019
89661-04L11
89661-04L12
89661-04L10
2020
89661-04L60 89661-04L61
–
QTY
NEW
00451-00001-LBL
Authorized Modifications Labels
NOTE
 The ECM/PCM should NOT be replaced as part of the Repair Procedure.
 Authorized Modifications Labels may be ordered in packages of 25 from the Materials
Distribution Center (MDC) through Dealer Daily – Parts – Dealer Support Materials Orders.
© 2021 Toyota Motor Sales, USA
–
1
T-SB-0043-20
Rev1
April 21, 2020
Page 3 of 6
MIL ON With DTC P211904 - 2GR-FKS (6MT)
Required Tools & Equipment
REQUIRED EQUIPMENT
SUPPLIER
Techstream ADVI*
PART NUMBER
QTY
TSADVUNIT
Techstream 2.0
TS2UNIT
ADE
1
Techstream Lite
TSLITEPDLR01
Techstream Lite (Green Cable)
TSLP2DLR01
*Essential SST.
NOTE
 Only ONE of the Techstream units listed above is required.
 Software version 15.30.027 or later is required.
 Additional Techstream units may be ordered by calling Approved Dealer
Equipment (ADE) at 1-800-368-6787.
 Use Techstream or an approved J2534 interface to perform flash reprogramming updates.
Visit techinfo.toyota.com for more information regarding J2534 reprogramming.
SPECIAL SERVICE TOOLS (SST)
PART NUMBER
QTY
Battery Diagnostic Tool*
DCA-8000P T
1
*Essential SST.
NOTE
Additional SSTs may be ordered by calling 1-800-933-8335.
© 2021 Toyota Motor Sales, USA
T-SB-0043-20
Rev1
April 21, 2020
Page 4 of 6
MIL ON With DTC P211904 - 2GR-FKS (6MT)
Calibration Information
CALIBRATION ID
MODEL
MODEL YEAR
TRANSMISSION
NEW
8966304B1300
8966304B1200
8966304B1100
8966304B1000
8966304B1400
8966304A7100
8966304A7000
8966304A7200
2019
8966304B4100
8966304B4000
8966304B4200
2020
8966304B9000
8966304B9100
2016 – 2017
Tacoma
VDS
PREVIOUS
2018
M/T
CZ5AN
SZ5AN
Repair Procedure
1. Using Techstream, check for DTC P211904 (ECM/PCM Throttle Actuator “A” Control Throttle
Body Range/Performance System Internal Failure).
Is DTC P211904 present?

YES — Continue to step 2.

NO — This bulletin does NOT apply. Continue diagnosis using the applicable
Repair Manual.
© 2021 Toyota Motor Sales, USA
T-SB-0043-20
Rev1
April 21, 2020
Page 5 of 6
MIL ON With DTC P211904 - 2GR-FKS (6MT)
Repair Procedure (continued)
2. Use Techstream to confirm if the ECM (PCM) calibration has been updated and check for the
Authorized Modifications Label affixed to the vehicle in the location shown below.
Is the calibration ID listed in Techstream and on the label the latest ECM (PCM) calibration?

YES — This bulletin does NOT apply. Continue diagnosis using the applicable
Repair Manual.

NO — Continue to step 3.
Figure 1. Location of Authorized Modifications Label on 2016 – 2020 Tacoma
TOYOTA MOTOR CORPORATION
AUTHORIZED MODIFICATIONS
THE FOLLOWING MODIFICATIONS HAVE BEEN MADE:
1
2
THESE MODIFICATIONS HAVE BEEN APPROVED
AS APPROPRIATE BY EPA AND CARB
3
DEALER CODE:
CHANGE AUTHORITY:
4
DATE:
5
1
Replacement ECM (PCM) Part Number
(e.g., 89661-04K64)
4
Date Completed
2
New Calibration ID (e.g., 8966304B1400)
5
This SB Number
3
Dealer Code
© 2021 Toyota Motor Sales, USA
T-SB-0043-20
Rev1
April 21, 2020
Page 6 of 6
MIL ON With DTC P211904 - 2GR-FKS (6MT)
Repair Procedure (continued)
3. Flash reprogram the ECM (PCM).
NOTE
 The battery diagnostic tool MUST be used in Power Supply Mode to maintain battery voltage at
13.5V while flash reprogramming the vehicle.
 For details on how to use the battery diagnostic tool, refer to the DCA-8000 Instruction Manual
located at TIS – Diagnostics – Tools & Equipment – Battery Diagnostics.
Follow the procedures outlined in T-SB-0134-16, Techstream ECU Flash Reprogramming
Procedure, and flash the ECM (PCM) with the NEW calibration file update.
4. Prepare and install the Authorized Modifications Label.
A. Using a permanent marker, enter the following information on the label:

ECM (PCM) part number [Refer to the Parts Information section for the NEW
PART NUMBER].

Calibration ID(s) [Refer to the Calibration Information section for the
NEW CALIBRATION ID].
Dealer Code.



Repair Date.
Change Authority [This bulletin number].
B. Install the Authorized Modifications Label onto the vehicle at the location shown in
Figure 1. The Authorized Modifications Label is available through the MDC,
P/N 00451-00001-LBL.
5. Test-drive the vehicle to confirm proper operation.
© 2021 Toyota Motor Sales, USA


© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.