NTB20-028A

Classification:
Reference:
EC20-013A
Date:
NTB20-028A
March 26, 2021
2020 KICKS; ENGINE STOPS RUNNING
WHEN COMING TO A STOP
This bulletin has been amended. See AMENDMENT HISTORY on the last page.
Please discard previous versions of this bulletin.
APPLIED VEHICLES:
2020 Kicks (P15)
IF YOU CONFIRM
A customer concern that the engine stopped running when coming to a stop and the MIL
was not ON,
And
The vehicle is easily restarted,
And
No DTCs are stored.
ACTION
1.
Confirm the current ECM part number.
If applicable:
2.
Adjust the base idle to 0 RPM with CONSULT-III plus (C-III plus).
3.
Reprogram the ECM.
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it
contains information that is essential to successfully completing this repair.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/3
SERVICE PROCEDURE
1.
Using C-III plus, confirm the current ECM part number and write it on the repair order.

If it matches one of the part numbers in Table A below, proceed to step 2 to
reprogram the ECM.

If it does not match one of the part numbers in Table A, ECM reprogramming is
not needed. Refer to the Electronic Service Manual (ESM) for further diagnostic
information.
Table A
MODEL
2020 Kicks
CURRENT ECM PART NUMBER: 237105RW2D, 5RW3D, 5RW4D, 5RW5D
Perform the following before starting the reprogramming procedure to prevent
damage to the control unit:

Connect the AC Adapter to the CONSULT PC.

Connect the CONSULT PC to the internet via Wi-Fi or a network cable.

Ensure ASIST on the CONSULT PC has been synchronized (updated) to the current
date and all C-III plus software updates (if any) have been installed.

Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.) within
range of the CONSULT PC and the VI. If Bluetooth® signal waves are within range
of the CONSULT PC during reprogramming, the reprogramming may be interrupted.

Turn OFF all vehicle electrical loads.

Connect a battery maintainer or smart charger, set to reflash mode or a similar
setting, to ensure the battery voltage stays between 12.0 V and 15.5 V.
HINT:

If you are not familiar with the reprogramming procedure, click here. This will link you
to the "CONSULT-III plus (C-III plus) ECM Reprogramming" general procedure.

Take the vehicle for a 10 minute drive in order to meet the following Idle Air Volume
Learning conditions:
o Engine coolant temperature: 70 - 100 °C (158 - 212 °F)
o Battery voltage: More than 12.9 V (At idle)
o Transmission: Warmed up

When reprogramming is complete, you will be required to perform Throttle Valve
Closed Position, Idle Air Volume Learning, Accelerator Closed Position and DTC
Erase.
o If IAVL does not complete, check the idle speed adjustment with C-III plus Work
Support and confirm that the idle is set to 0 RPM. Once the idle speed is set to
0 rpm, IAVL can be completed.
2/3
NTB20-028A
2.
Adjust the base idle to 0 rpms with C-III plus.
3.
Reprogram the ECM.
4.
After completing Erase ALL DTCs, print a copy of the C-III plus screen showing the
before and after part numbers of the control unit and attach it to the repair order.
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
(1)
(2)
DESCRIPTION
PFP
OP CODE
SYM
DIA
FRT
Reprogram ECM
(1)
DE97AA
ZE
32
(2)
Reference the electronic parts catalog and use the ECM as the Primary Failed Part
(PFP).
Reference the current Nissan Warranty Flat Rate Manual and use the indicated Flat
Rate Time (FRT).
AMENDMENT HISTORY
PUBLISHED DATE REFERENCE
DESCRIPTION
March 31, 2020
NTB20-028
Original bulletin published
March 26, 2021
NTB20-028A
Tabe A on page 2 revised
3/3
NTB20-028A