A0121042062862_1
Service Bulletin Details
Public Details for: A0121042062862_1
- 2021 -
Models from 2021
2021 AUDI A4 |
2021 AUDI A5 |
2021 AUDI A5 CABRIOLET |
01 MIL on, DTC P227900, P001600 and/or P001700 is stored in the ECM 01 21 04 2062862/1 April 13, 2021. Model(s) Year VIN Range Vehicle-Specific Equipment A4, A5 Cabriolet, and A5 Sportback 2021 All 2.0 TFSI Condition Customer statement: MIL on. Workshop findings: The customer concern can be reproduced. The following DTC is stored in the engine control module (ECM), J623 (address word 0001): DTC P227900 (Leakage air in intake system) with symptom code 43055. Additional DTCs that can be stored in the engine control module (ECM), J623 (address word 0001): DTC P001600 (bank 1, camshaft pos./crankshaft position sensor incorrect assignment) with symptom codes 43056 and/or 43058. And/or DTC P001700 (bank 1, camshaft pos./crankshaft position sensor 2 incorrect assignment) with symptom code 43057 and/or 43059. Note: DTC P227900 is recorded first when reviewing the time line. P001600 and P001700 are entered shortly after P227900. No other relevant DTCs must be present and must be diagnosed separately. This TSB only applies for the combination of possible DTCs listed above. Technical Background Under investigation. Page 1 of 3 © 2021 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Production Solution Not applicable. Service Please replace the intake manifold pressure sender according to ELSA repair instructions. Note: After replacing the intake manifold pressure sender, it is very important to reset the air pressure-based camshaft angle adaptation/correction as otherwise the problem will not be solved. This can be done in self-diagnosis mode >> basic setting >> air pressure-based camshaft angle adaptation/camshaft angle correction. Warranty Claim Type: 110 up to 48 Months/50,000 Miles. G10 for CPO Covered Vehicles – Verify Owner. If the vehicle is outside any warranty, this Technical Service Bulletin is informational only. Service Number: 2471 Damage Code: 0040 Labor Operations: Remove and install intake manifold pressure sender. 2471 1915 See SRT with associated operations Diagnostic Time: GFF – Checking and clearing 0150 0000 Time stated on the diagnostic protocol (Max 30 TU Road test prior to the service procedure 0121 0002 10 TU Road test after the service procedure 0121 0004 10 TU Claim Comment: As per TSB #2062862/1 All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to review or audit by Audi Warranty. Page 2 of 3 © 2021 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Required Parts and Tools Always check with your Parts Department and/or ETKA for the latest information and parts bulletins. Part Number Part Description Quantity See ETKA Fasteners, Bolts, Nuts, and Screws as needed per the Repair Manual See ETKA/ELSA 06L906051K Pressure Sensor 01 Tool Number Tool Description VAS 6160/VAS 6150 VAS tester with the current version of ODIS (Windows 10) Additional Information All parts and service references provided in this TSB (2062862) are subject to change and/or removal. ©2021 Audi of America, Inc. All rights reserved. The information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. Page 3 of 3 © 2021 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.