ITB16-008C

Service Bulletin Details

Public Details for: ITB16-008C

Mil on with P0603 stored for ecm back up circuit this bulletin has been amended. See amendment history on page 3. Please discard previous versions of this bulletin.


- 2019 - 2018 - 2017 - 2016 - 2015 -

Models from 2019
2019 INFINITI Q70
Models from 2018
2018 INFINITI Q70
Classification:
Reference:
Date:
EC16-005C
ITB16-008C
April 1, 2021
MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT
This bulletin has been amended. See AMENDMENT HISTORY on page 3.
Please discard previous versions of this bulletin.
APPLIED VEHICLES:
2015 Q50 (V37)
2015 Q60 (V36)
2015-2019 Q70 (Y51)
2015-2017 QX50 (J50)
2015 QX60 (L50)
2015-2017 QX70 (S51)
NOTE: This TSB only applies to vehicles equipped with multi-port injection (MPI).
IF YOU CONFIRM
The MIL is “ON” with DTC P0603 (ECM BACK UP/CIRCUIT).
ACTION
1. Confirm that the battery voltage is 11 volts, or more, with the ignition ON (engine OFF, not running).
2. Erase the DTC.
3. Perform DTC confirmation steps in the Service Procedure.
4. Confirm 1st trip DTC P0603 is not stored.
NOTE: P0603 is often the result of low battery voltage, discharged battery or battery terminal
disconnections.
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing.
You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to
successfully completing this repair.
Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained
individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe
that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti retailer to determine if this
applies to your vehicle.
1/3
SERVICE PROCEDURE
NOTE: This DTC may have been stored due to low battery voltage, discharged battery or battery terminal
disconnections.
1. Confirm the battery voltage is at least 11 volts, or more, with the ignition ON.

While checking the battery voltage, make sure the battery cables are clean and tight.

Resolve any low battery condition before proceeding. Repairs for a low battery condition are not
covered by this bulletin
2. Connect the C-III plus VI to the vehicle.
3. Open C-III plus on the CONSULT PC.
4. Turn the ignition “ON”, but Do Not Start engine.
5. Erase the DTC.
6. Turn the ignition OFF.
7. Turn the Ignition ON and wait for at least 1 second.
8. Turn the ignition OFF and wait for at least 10 seconds.
9. Repeat step 7 and step 8 ten times and then proceed to step 10.
10. Turn the ignition ON.

If P0603 is currently stored as a 1st trip DTC, refer to the ESM for further diagnostic information.

If P0603 is NOT currently stored as a 1st trip DTC, the Service Procedure is complete.
2/3
ITB16-008C
CLAIMS INFORMATION
Submit a Primary Operation (PO) type line claim using the following claims coding:
DESCRIPTION
OP CODE
SYM
DIA
FRT
DTC P0603 SYSTEM CHECK
EX2LAA
HD
32
0.4 hr
AMENDMENT HISTORY
PUBLISHED DATE
REFERENCE
DESCRIPTION
February 22, 2016
NTB16-018
Original bulletin published
January 4, 2017
NTB16-018A
APPLIED VEHICLES updated
March 26, 2018
NTB16-018B
APPLIED VEHICLES updated
April 1, 2021
NTB16-018C
APPLIED VEHICLES updated
3/3
ITB16-008C


© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.