NTB21-030

Classification:
Reference:
BR21-002
Date:
NTB21-030
April 15, 2021
VOLUNTARY SERVICE CAMPAIGN
ABS/VDC REPROGRAMMING
CAMPAIGN ID #:
APPLIED VEHICLES:
P1A01
2021 Rogue (T33)
Check Service COMM or Dealer Business Systems (DBS)
National Service History to confirm campaign eligibility.
INTRODUCTION
Nissan is conducting this voluntary service campaign on certain specific model year 2021
Rogue models, to inspect, and if applicable, reprogram the ABS/VDC control unit. This
service will be performed at no charge to the customer for parts or labor.
IDENTIFICATION NUMBER
Nissan has assigned identification number P1A01 to this campaign. This number must
appear on all communication and documentation of any nature dealing with this campaign.
DEALER RESPONSIBILITY
Dealers are to repair vehicles falling within range of this campaign that enter the service
department. This includes vehicles purchased from private parties, vehicles presented by
transient (tourists) owners, and vehicles in a dealer’s inventory.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/24
SERVICE PROCEDURE
IMPORTANT: Before starting, make sure:

ASIST on the C-III plus has been synchronized (updated) to the current date.

All C-III plus software updates (if any) have been installed.

Connect a battery maintainer or smart charger set to reflash mode or a
similar setting. If the vehicle battery voltage drops below 12.0V or rises
above 15.5V during reprogramming, the ABS/VDC control unit may be
damaged.

Be sure to turn off all vehicle electrical loads.
If a vehicle electrical load remains on, the ABS/VDC control
unit may be damaged.

Be sure to connect the AC Adapter.
If the C-III plus battery voltage drops during reprogramming, the
process will be interrupted and the ABS/VDC control unit may be
damaged.

Turn off all external Bluetooth® devices (e.g., cell phones, printers, etc.)
within range of the C-III plus and the VI. If Bluetooth® signal waves are
within range of the C-III plus or VI during reprogramming,
reprogramming may be interrupted and the ABS/VDC control unit may
be damaged.
1.
Connect a battery maintainer/smart charger to the vehicle.
2.
Turn on the ignition by pressing the ignition button 1 time WITHOUT depressing the
brake pedal.
3.
Verify all electrical loads are turned off.
4.
Connect the VI to the vehicle.
5.
Start C-III plus.
2/24
NTB21-030
6.
Wait for the VI to be recognized.

7.
The serial number will display when the VI is recognized.
Select Re/programming, Configuration.
The VI is
recognized
Figure 1
3/24
NTB21-030
8.
Check the box to confirm the precaution instructions have been read, and then select
Next.
NOTE: Use the arrows (if needed) to view and read all the precautions.
Figure 2
9.
Select Automatic Selection(VIN).
Figure 3
4/24
NTB21-030
10.
Allow the C-III plus to perform automatic VIN selection.
Figure 4
11.
Confirm the VIN or Chassis # is correct, and then select Confirm.
XXXXXXXXXXXXXXX
Figure 5
5/24
NTB21-030
12.
Allow the System call to be performed.
Figure 6
13.
Confirm the VIN is correct for the vehicle, and then select Confirm.
XXXXXXXXXXXXXXXXXX
Figure 7
6/24
NTB21-030
14.
Select ABS.
Figure 8
15.
Select Reprogramming.
Figure 9
7/24
NTB21-030
16.
Confirm the current Part Number and write it on the repair order.


If it matches one of the part numbers in Table A, continue to step 17 on page 9.
If it does not match one of the part numbers in Table A, reprogramming is not
needed. Close C-III plus and skip to CLAIMS INFORMATION on the last page.
XXXXXXXXXXXXXXX
XXXXX
XXXXXXXXXXXXXXX
Figure 10
Table A
MODEL
YEAR
CURRENT PART NUMBER: 47855-
Rogue
2021
6RR7A, 6RR7B,
6RR8A, 6RR8B, 6RR8E, 6RR8F
6RR9E, 6RR9F
6RW3A, 6RW3B
6RW4A, 6RW4B
6RW8C, 6RW8D
6RW9C, 6RW9D
8/24
NTB21-030
17.
Select Save.
XXXXXXXXXXXXXXX
XXXXX
XXXXXXXXXXXXXXX
Figure 11
18.
Check the box to confirm the precaution instructions have been read, and then select
Next.
NOTE: Use the arrows (if needed) to view and read all the precautions.
Figure 12
9/24
NTB21-030
19.
Read the Current Part Number and Part Number After Repro/programming. They
should be different (Figure 13).
XXXXX
XXXXX
XXXXXXXXXXXX
XXXXXXXXXXXX
Figure 13
20.
Select Next.
XXXXX
XXXXX
XXXXXXXXXXXX
XXXXXXXXXXXX
Figure 14
10/24
NTB21-030
21.
Confirm the battery charger is on and the battery voltage is between 12V-15.5V, and
then select Next.
Verify battery
voltage is between
12V-15.5V
Figure 15
22.
Confirm all Judgment items are OK, and then select Start.
Figure 16
11/24
NTB21-030
23.
Select USA/CANADA Dealers from the drop down menu, and then select OK.
Figure 17
24.
If the Script Error message in Figure 18 is shown, Select Yes.
Figure 18
12/24
NTB21-030
25.
Login using your NNAnet credentials and select Submit.
Figure 19
26.
Allow Transfer Data to complete.
Figure 20
13/24
NTB21-030
27.
If the screen in Figure 21 displays, reprogramming is complete. Select Next and skip
to step 28 on page 16. If the screen in Figure 21 does not display (indicating that
reprogramming did not complete), refer to the information on the next page.
Figure 21
14/24
NTB21-030
Recovery:
Do not disconnect the VI or shut down C-III plus if reprogramming does not
complete.
If reprogramming does not complete and the “!?” icon displays as shown in
Figure 22:

Check battery voltage
(12.0 V – 15.5 V).

Ignition is ON, engine is OFF.

External Bluetooth® devices
are OFF.

All electrical loads are OFF.

Select retry and follow the on
screen instructions.

“Retry” may not go through on
first attempt and can be
selected more than once.
XXXXXX
XXXXXX
XXXX
XXXXXXXXX
XXX
Figure 22
If reprogramming does not complete and the “X” icon displays as shown in
Figure 23:

Check battery voltage
(12.0 V – 15.5 V).

CONSULT A/C adapter is
plugged in.

Ignition is ON, engine is OFF.

Transmission is in Park.

All C-III plus / VI cables are
securely connected.

All C-III plus updates are
installed.

Select Home, and restart the
reprogram procedure from the
beginning.
XXXXXX
XXXXXX
XXXX
XXXXXXXXX
XXX
Figure 23
15/24
NTB21-030
28.
Press the ignition button 1 time to turn off the ignition.

29.
If the ignition does not turn off when the ignition button is pressed and released,
press and hold the ignition button to turn the ignition off.
Press the ignition button 1 time to turn the ignition back on.

C-III plus should automatically proceed to Erase All DTCs.
Figure 24
16/24
NTB21-030
30.
Select Print and attach the reprogramming result to the repair order.
47855XXXXX
47855XXXXX
XXXXXXXXXXXX
Figure 25
31.
Select Confirm.
47855XXXXX
47855XXXXX
XXXXXXXXXXXX
Figure 26
17/24
NTB21-030
32.
Select Home.
Figure 27
33.
Press the ignition button one time to turn off the ignition. If the ignition does not turn off
when the ignition button is pressed and released, press and hold the ignition button to
turn the ignition off.
a) Remove the key from the vehicle.
b) Close all the doors.
c) Lock the doors using the key.
d) Allow the vehicle to sit for 2 minutes without opening any doors.
e) Unlock the vehicle.
f) Open the driver door.
g) Enter the vehicle.
h) Turn on the ignition by pressing the ignition button 1 time WITHOUT depressing the
brake pedal.
18/24
NTB21-030
Erase DTCs
34.
Select Diagnosis (All Systems).
Figure 28
35.
Select Automatic Selection(VIN).
Figure 29
19/24
NTB21-030
36.
Allow the C-III plus to perform automatic VIN selection.
Figure 30
37.
Confirm the VIN or Chassis # is correct, and then select Confirm.
XXXXXXXXXXXXXXX
Figure 31
20/24
NTB21-030
38.
Allow the System call to be performed.
Figure 32
39.
Confirm the VIN is correct for the vehicle, and then select Confirm.
XXXXXXXXXXXXXXXXXX
Figure 33
21/24
NTB21-030
40.
Select ERASE.
Figure 34
41.
Select Execute.
Figure 35
22/24
NTB21-030
42.
Select Close.
Figure 36
43.
Close the C-III plus application.
44.
Press the ignition button one time to turn off the ignition. If the ignition does not turn off
when the ignition button is pressed and released, press and hold the ignition button to
turn the ignition off.
45.
Disconnect the VI and remove it from the vehicle.
46.
Turn off and disconnect the battery maintainer/smart charger.
47.
Close the hood.
23/24
NTB21-030
CLAIMS INFORMATION
Submit a “CM” line claim using the following claims coding:
CAMPAIGN (“CM”) ID
P1A01
DESCRIPTION
OP CODE
FRT
Reprogram ABS Actuator
P1A010
0.6 hrs.
Reprogram Not Needed
P1A011
0.3 hrs.
AMENDMENT HISTORY
PUBLISHED DATE REFERENCE
April 15, 2021
NTB21-030
DESCRIPTION
Original bulletin published
24/24
NTB21-030