NTB12087
Service Bulletin Details
Public Details for: NTB12087
If you confirm: the cruise control turns off without pressing the brake pedal or using the cruise control switches while driving with the cruise control set. Action: 1. Refer to step 6 in the service procedure to confirm this bull
Classificatio n: EC12-04 Reference: Date: NTB12-087 October 3, 2012 2009-2010 FRONTIER, XTERRA, AND PATHFINDER; CRUISE CONTROL INTERMITTENTLY TURNS OFF APPLIED VEHICLES: APPLIED ENGINE: 2009 – 2010 Frontier (D40) 2009 – 2010 Xterra (N50) 2009 – 2010 Pathfinder (R51) VQ40 ONLY IF YOU CONFIRM: The cruise control turns off without pressing the brake pedal or using the cruise control switches while driving with the cruise control set. ACTION: 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM. CLAIMS INFORMATION Submit a Primary Part (PP) type line claim using the following claims coding: DESCRIPTION PFP OP CODE SYM DIA FRT Reprogram ECM (1) DE97AA HD 32 (2) (1) Reference the Repair Order and use the current ECM P/N written down in step 2 of the Service Procedure as the PFP. (2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated FRT. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. 1/10 SERVICE PROCEDURE NOTE: • Most instructions for reprogramming with CONSULT-III plus (C-III plus) are displayed on the CONSULT PC screen. • If you are not familiar with the reprogramming procedure, click here. This will link you to the "CONSULT- III plus (C-III plus) ECM Reprogramming" general procedure. • Take the vehicle for a 10 minute drive in order to meet the following Idle Air Volume Learn (IAVL) conditions: ¾ Engine coolant temperature: 70 -100°C (158 - 212°F) ¾ Battery voltage: More than 12.9V (At idle) ¾ Transmission: Warmed up Figure A • After reprogramming is complete, you will be required to perform Throttle Valve Closed Position, Idle Air Volume Learn, Accelerator Closed Position, and DTC erase. CAUTION: • Connect a battery charger to the vehicle battery. If the vehicle battery voltage drops below 12.0V or above 15.5V during reprogramming, the ECM may be damaged. • Be sure to turn OFF all vehicle electrical loads. If a vehicle electrical load remains ON, the ECM may be damaged. • Be sure to connect the AC Adapter. If the CONSULT PC battery voltage drops during reprogramming, the process will be interrupted and the ECM may be damaged. • Turn off all external Bluetooth® devices (e.g., cell phones, printers, etc.) within range of the CONSULT PC and the VI. If Bluetooth® signal waves are within range of the CONSULT PC during reprogramming, reprogramming may be interrupted and the ECM may be damaged. 2/10 NTB12-087 1. Connect the CONSULT PC to the vehicle to begin the reprogramming procedure. 2 Open ASIST on the CONSULT PC and start C-III plus. 3. Wait for the plus VI to be recognized / connected. • Serial number will display when the plus VI is recognized / connected. 4. Select Re/programming, Configuration. VI is recognized Step 4 Figure 1 5. Follow the on-screen instructions and navigate the C-III plus to the screen shown in Figure 2 on the next page. 3/10 NTB12-087 6. When you get to the screen shown in Figure 2, confirm this bulletin applies as follows. A. Find the ECM Part Number and write it on the repair order. NOTE: This is the current ECM Part Number (P/N). 6A: Current ECM P/N Figure 2 B. Compare the P/N you wrote down to the numbers in the Current ECM Part Number column in Table A on page 5. • If there is a match, this bulletin applies. Continue with the reprogramming procedure. • If there is not a match, this bulletin does not apply. Close C-III plus and refer to ASIST for further diagnostic information. 4/10 NTB12-087 Table A Model Year 2009 2010 Model Current ECM Part Number: 23710- ZL08A, ZL08B, ZL08C, ZL08D Pathfinder (R51) ZL12A, ZL13A ZL34A, ZL35A ZL00A, ZL00C ZL01A, ZL01B, ZL01C, ZL01D ZL02A, ZL02C ZL03A, ZL03B, ZL03C, ZL03D ZL04A, ZL04C Frontier (D40) ZL05A, ZL05B, ZL05C, ZL05D VQ35 ZL06A, ZL06C ZL07A, ZL07B, ZL07C, ZL07D ZL30A, ZL31A, ZL32A, ZL33A ZL60A, ZL61A, ZL62A, ZL63A, ZL64A, ZL65A ZL66A, ZL67A ZL00A, ZL00C ZL02A, ZL02C Xterra (N50) ZL04A, ZL04C ZL06A, ZL06C ZL30A, ZL31A, ZL32A, ZL33A ZL92A, ZL93A, ZL94A, ZL95A Pathfinder (R51) ZL92B, ZL93B, ZL94B, ZL95B ZZ70A, ZZ73A, ZZ75A, ZZ76A, ZZ79A ZZ70B, ZZ73B, ZZ75B, ZZ76B Frontier (D40) ZZ81A, ZZ82A, ZZ83A, ZZ84A, ZZ85A, ZZ87A VQ35 ZZ88A, ZZ89A ZZ82B, ZZ85B, ZZ88B ZL44A, ZL45A, ZL47A ZZ70A, ZZ73A, ZZ76A, ZZ79A, ZZ82A, ZZ85A, ZZ88A Xterra (N50) ZZ70B, ZZ73B, ZZ76B, ZZ82B, ZZ85B, ZZ88B ZL45A 5/10 NTB12-087 7. Follow the on-screen instructions to navigate C-III plus and reprogram the ECM. NOTE: • In some cases, more than one new P/N for reprogramming is available. ¾ In this case, the screen in Figure 3 displays. • Select and use the reprogramming option that does not have the message “Caution! Use ONLY with NTBXX-XXX”. • If you get this screen and it is blank (no reprogramming listed), it means there is no reprogramming available for this vehicle. Close C-III plus and refer back to ASIST for further diagnosis. xxxxx-xxxxx xxxxx-xxxxx xxxxxxxxxxxxxxxxxxxxxx xxxxx-xxxxx xxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxx Figure 3 6/10 NTB12-087 8. When the screen in Figure 4 displays, reprogramming is complete. 9. Disconnect the battery charger from the vehicle. 10. Select Next. Step 10 Figure 4 CAUTION: If reprogramming does not complete and the !? displays as shown in Figure 5 on page 8: • Check battery voltage (12.0 – 15.5V). • Ignition is ON, engine is OFF. • External Bluetooth® devices are OFF • All electrical loads are OFF. • • Select retry and follow the on screen instructions. Retry may not go through on first attempt and can be selected more than once. 7/10 NTB12-087 Figure 5 OR: If reprogramming does not complete and the X displays as shown in Figure 6: Do not disconnect VI or shut down Consult III plus if reprogramming does not complete. • Check battery voltage (12.0 – 15.5V). • CONSULT A/C adapter is plugged in. • Ignition is ON, engine is OFF. • Transmission in Park • • All C-III plus / VI cables are securely connected. All C-III plus updates are installed. • Select Home, and restart the reprogram procedure from the beginning. Figure 6 8/10 NTB12-087 NOTE: • In the next steps, you will perform Throttle Valve Closed Position, Idle Air Volume Learn, Accelerator Closed Position, and DTC erase. • These operations are required before C-III plus will provide the final reprogramming confirmation report. 11. Follow the on-screen instructions to perform the following: • Throttle Valve Closed Position • Idle Air Volume Learn (IAVL) NOTE: o Listed below are common conditions required for IAVL to complete. o If IAVL does not complete within a few minutes, a condition may be out of range. o Refer to the appropriate Electronic Service Manual (ESM) for specific conditions required for the vehicle you are working on. ¾ ¾ ¾ ¾ ¾ ¾ ¾ Engine coolant temperature: 70 -100° C (158 - 212°F) Battery voltage: More than 12.9V (At idle) Selector lever: P or N Electric load switch: OFF (Air conditioner, headlamp, rear window defogger) Steering wheel: Neutral (Straight-ahead position) Vehicle speed: Stopped Transmission: Warmed up • Accelerator Pedal Close Position Learning • Erase DTCs Continue to the next page. 9/10 NTB12-087 12. When the entire reprogramming process is complete, the screen in Figure 7 will display. 13. Verify the before and after part numbers are different. 14. Print a copy of this screen (Figure 7) and attach it to the repair order for warranty documentation. 15. Select Confirm. Step 13 Step 14 Step 15 Figure 7 16. Close C-III plus. 17. Turn the ignition OFF. 18. Disconnect the plus VI from the vehicle. 19. Test drive the vehicle and make sure it operates correctly and the MIL is OFF. • If the MIL comes ON, go back to ASIST for further diagnostic information. • Diagnosis and repairs beyond ECM reprogramming are not covered by this bulletin. 10/10 NTB12-087