ITB14045

Service Bulletin Details

Public Details for: ITB14045

If you confirm one or both steering wheel switch chrome finishers on an applied vehicle has come off. Action follow the procedure in this bulletin to install the new steering wheel switch chrome finisher(s) listed in the parts informat


- 2014 -

Models from 2014
2014 INFINITI Q50
Classification:
Reference:
Date:
ST14-010
ITB14-045
October 9, 2014
2014 Q50; STEERING WHEEL SWITCH CHROME FINISHER(S) COMES OFF
APPLIED VEHICLES:
2014 Q50 (V37)
2014 Q50 Hybrid (V37)
IF YOU CONFIRM
One or both steering wheel switch chrome finishers on an Applied Vehicle has come off.
ACTION
Follow the procedure in this bulletin to install the new steering wheel switch chrome finisher(s) listed in the
Parts Information section.
NOTE: Do not replace the steering wheel assembly for this incident, if it should occur.
Steering
Wheel Switch
Chrome
Finisher
Figure 1 - LH Chrome Finisher
Figure 2 - RH Chrome Finisher
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You
MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully
completing this repair.
Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained
individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe
that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti dealer to determine if this
applies to your vehicle.
1/4
SERVICE PROCEDURE
NOTE: Installation of the LH side chrome finisher is shown in this procedure. Installation of the RH side chrome
finisher is identical.
1. Use a dry cloth to remove any adhesive residue
that may be on the switch.
Figure 3
2. Confirm the proper orientation of the new chrome finisher by placing it on the switch and snapping it into
place.
NOTE: The finisher will not fit properly if it is upside down.
Correct orientation
Incorrect orientation
Finisher snaps into place and
there are no gaps
Finisher does not snap
into place
Figure 4
X

Figure 5
2/4
ITB14-045
3. Remove the new chrome finisher and carefully apply a small amount of adhesive to the two areas of the
switch shown Figure 6.

Use the adhesive listed in the Parts Information section.

Use a pick tool or similar tool with a fine point to apply the adhesive.
Carefully apply
a small amount of
adhesive here…
… and here
Figure 6
Figure 7
3/4
ITB14-045
Press down and
snap finisher
into place
4. Align the new chrome finisher over the switch
and press down until it snaps into place.
5. Inspect the area around the chrome finisher
and make sure no adhesive is visable.
Figure 8
PARTS INFORMATION
DESCRIPTION
PART NUMBER
QUANTITY
25550-4GA1E
1 (if needed)
See Figure 2 on page 1 for reference.
The LH and RH parts are not identical.
25550-4GA2E
1 (if needed)
LOCKTITE® 495 Instant Adhesive (or equivalent)
Local source
Shop supply
STRG SW RING - LH
See Figure 1 on page 1 for reference.
The LH and RH parts are not identical.
STRG SW RING - RH
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
PFP
OP CODE
SYM
DIA
FRT
REPLACE STEERING SWITCH CHROME COVER
(ONE OR BOTH SIDES)
(1)
RX4RA1
ZE
32
0.2
(1) Refer to the electronic parts catalog (FAST) and use the Steering Wheel assembly part number (48430xxxxx) as the Primary Failed Part (PFP).
4/4
ITB14-045


© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.