AudiTechRef2019
Service Bulletin Details
Public Details for: AudiTechRef2019
Pre-delivery inspection technician reference document
- 2019 -
Models from 2019
2019 Pre-Delivery Inspection Technician Reference Document Effective 3-20-2019-US Version 1.6 Table of Contents Technician Reference Document Technician Reference Document Overview The Pre-Delivery Inspection Technician Reference Document is designed to be a resource used in hand with the Pre-Delivery Inspection Checklist (PDI). The PDI Checklist has been simplified to make the process more efficient, and in doing so, this document has been created to be used as a reference for checklist items that may have additional information. On the PDI Checklist, you find that certain items have been notated with an asterisk symbol (*), this lets you know that additional information can be found in this Technician Reference Document. Below you will find a list of each model, with the page numbers to their left. After navigating to the desired page, you will notice each model page is formatted similarly to the PDI Checklists. After each section title is the original checklist item, followed by any additional information specific to that model. Table of Contents 3-4 A3 Sedan & Cabriolet/S3/RS 3 5-6 A4/S4/A4 allroad 7-8 A5/S5/RS 5 9-11 A6 12-14 A7 15-16 A8 L 17-18 e-tron 19-20 Q3 21-22 Q5/SQ5 23-24 Q7 25-26 Q8 27-28 TT/TTS/TTRS Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 2 A3 Sedan & Cabriolet/S3/RS 3 Technician Reference Document Vehicle Preparation Trunk Inspection (continued) • Perform any open campaigns • Check battery clamps for proper torque Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation (Sedan only) Verify open/close/vent/deflector at edge and sunshade operation Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) Lighting and Windshield • Test front washers (and headlight washers on S3 and RS 3) Headlights must be on to test functionality of the headlight washers Trunk Inspection • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit • Verify temporary inflatable spare tire is present (A3 Sedan, S3, and A3 Cabriolet FWD only) See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet Effective 3-20-2019-US Version 1.6 Settings • Set time source setting to “GPS” (if equipped) and set auto daylight savings time to “on”* Change time zone appropriate to dealer location • Verify and set language and measurement units This can be changed in the Settings menu by going to Menu > Vehicle > Vehicle settings • Verify Speech Dialog System is operating (if equipped) Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level (if equipped) Via “Menu > Vehicle > Left Option > Driver Assistance > Parking Aid” • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning This can be changed in the Driver Assistance Settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual > Select OffMedia / Radio / SAT Model Year 2019 | Audi Pre-Delivery Reference Document | 3 A3 Sedan & Cabriolet/S3/RS 3 Technician Reference Document Media / Radio / SAT Driver Assistance • Verify HD Radio is turned “off” • Verify operation of Audi parking system (if equipped) This can be found in the Radio/Settings Menu Verify operation of Audi parking system sensors with rear view camera (if equipped) Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Right Option > Wi-Fi® options > Wi-Fi® “On”) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system • Enable Google Earth view for navigation (if equipped) Cabriolet Functionality • Test operation of power folding top Perform with engine running to conserve battery power Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature Enable Google Earth view in the Navigation > Map Settings and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol. On-Hoist Inspection • Inspect wheel bolts for proper torque Use torque wrench to verify • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 4 A4/S4/A4 allroad Technician Reference Document Vehicle Preparation Interior • Perform any open campaigns • Check operation of window, lock, and seat controls Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating • Check rear view mirror operation Check self-dimming function/lighting • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding Settings • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” Change time zone appropriate to the dealer location Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Verify and set language and measurement units This can be changed in the Settings menu by going to Menu > Vehicle > Vehicle settings • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Lighting and Windshield • Test front washers (and headlight washers if equipped) Headlights must be on to test functionality of the headlight washers Trunk Inspection • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit • Set spare tire pressure See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet Via “Menu > Vehicle > Left Option > Driver Assistance > Parking Aid” • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, Settings > Music volume while parking (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual > Select Off • Check battery clamps for proper torque Refer to Elsa Pro for specification Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 5 A4/S4/A4 allroad Technician Reference Document Media / Radio / SAT Driver Assistance • Verify HD Radio is turned “off” • Verify operation of parking system (if equipped) This can be found in the Radio/Settings Menu Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Right Option > Wi-Fi® options > Wi-Fi® “On”) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system • Enable Google Earth view for navigation (if equipped) Enable Google Earth view in the Navigation > Map Settings and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol. Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-up display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature On-Hoist Inspection • Inspect wheel bolts for proper torque Use torque wrench to verify • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 6 A5/S5/RS 5 Technician Reference Document Vehicle Preparation Interior • Perform any open campaigns • Check operation of window, lock, and seat controls Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding Settings • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) Lighting and Windshield • Test front washers (and headlight washers if equipped) Headlights must be on to test functionality of the headlight washers Trunk Inspection • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit • Set spare tire pressure See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification Effective 3-20-2019-US Version 1.6 Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Setup/Settings menu • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Via Menu > Vehicle > Driver Assistance > Parking Aid • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, Settings > Music volume while parking (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual->Select Off Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu Model Year 2019 | Audi Pre-Delivery Reference Document | 7 A5/S5/RS 5 Technician Reference Document Audi connect® (USA ONLY) (if equipped) Driver Assistance • Turn on the Wi-Fi® hotspot (if equipped) • Verify operation of parking system (if equipped) Ensure the wireless network is turned on (Telephone > Right Option > Wi-Fi® options > Wi-Fi® “On”) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system • Enable Google Earth view for navigation (if equipped) Enable Google Earth view in the Navigation > Map Settings and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol. On-Hoist Inspection Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Convertible Functionality (if equipped) • Test operation of power folding top Perform with engine running to conserve battery power • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify • Set and store tire pressures for either sold vehicle OR stock inventory vehicle Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 8 A6 Technician Reference Document Vehicle Preparation Trunk Inspection (continued) • Perform any open campaigns • Set spare tire pressure Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification • Place one PR Number Label in the Warranty and Maintenance Book inside front cover and one on the Rear Panel Sill Frame under the luggage compartment floor, if not already there For vehicles produced prior to September 12, 2018 Labels are located in the trunk on top of spare tire Rear Panel Sill Frame location: Top Arrow • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing (if equipped) For vehicles equipped with the power door closing feature, check all doors for proper closing Lighting and Windshield • Test front washers (and headlight washers if equipped) Headlights must be on to test functionality of the headlight washers Trunk Inspection • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 9 A6 Technician Reference Document Trunk Inspection (continued) Settings Warranty and Maintenance inside cover placement • Set Time source setting to “GPS” and set Auto daylight savings time to “on” Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Setup/Settings menu • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, Settings > Music volume while parking (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features This can be changed in the Driver Assistance Settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual > Select Off Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify operation of heated/ventilated and massaging seats (if equipped) Check both front and rear. Massaging feature is in the front seats only (if equipped) • Verify proper operation of climate control* Ensure proper heating and A/C cooling, open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” ) • Check Wi-Fi® hotspot visibility. No data available at PDI due to dealer demo mode (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX is the last four digits of the VIN. Via Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings > Access point (SSID) • Enable satellite map for navigation (if equipped) Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom right-hand corner of the Navigation map screen. On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 10 A6 Technician Reference Document On-Hoist Inspection (continued) • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up Display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 11 A7 Technician Reference Document Vehicle Preparation Trunk Inspection (continued) • Perform any open campaigns • Set spare tire pressure Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification • Place one PR Number Label in the Warranty and Maintenance Book inside front cover and one on the Rear Panel Sill Frame under the luggage compartment floor, if not already there For vehicles produced prior to September 12, 2018 Labels are located in the trunk on top of spare tire Rear Panel Sill Frame location: Top Arrow • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing (if equipped) For vehicles equipped with the power door closing feature, check all doors for proper closing Lighting and Windshield • Test front washers (and headlight washers if equipped) Headlights must be on to test functionality of the headlight washers Trunk Inspection • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 12 A7 Technician Reference Document Trunk Inspection (continued) Settings Warranty and Maintenance inside cover placement • Set Time source setting to “GPS” and set Auto daylight savings time to “on” Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Setup/Settings menu • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, Settings > Music volume while parking (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify operation of heated/ventilated and massaging seats (if equipped) Check both front and rear. Massaging feature is in the front seats only (if equipped) • Verify proper operation of climate control* Ensure proper heating and A/C cooling, open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation This can be changed in the Driver Assistance Settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual > Select Off Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” ) • Check Wi-Fi® hotspot visibility. No data available at PDI due to dealer demo mode (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX is the last four digits of the VIN. Via Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings > Access point (SSID) • Enable satellite map for navigation (if equipped) Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom right-hand corner of the Navigation map screen. On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 13 A7 Technician Reference Document On-Hoist Inspection (continued) • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 14 A8 L Technician Reference Document Vehicle Preparation Trunk Inspection (continued) • Perform any open campaigns • Set spare tire pressure Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • Verify operation of heated/ventilated and massaging seats (if equipped) • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding Check both front and rear. Massaging feature is in the front seats only (if equipped) • Exit diagnosis; diagnostic log for delivery inspection is sent automatically Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing For vehicles equipped with the power door closing feature, check all doors for proper closing Lighting and Windshield • Test front washers (and headlight washers if equipped) Headlights must be on to test functionality of the headlight washers Trunk Inspection • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit • Verify proper operation of climate control Ensure proper heating and A/C cooling, open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on” Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Setup/Settings menu • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, Settings > Music volume while parking (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 15 A8 L Technician Reference Document Settings (continued) Driving Performance (continued) • Turn off Manual Speed Warning (if equipped) • Verify engine performance and acceleration This can be changed in the Driver Assistance Settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual > Select Off Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Audi connect® (USA ONLY) Driver Assistance • Turn on the Wi-Fi® hotspot (if equipped) • Verify operation of parking system Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” ) • Check Wi-Fi® hotspot visibility. No data available at PDI due to dealer demo mode (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX is the last four digits of the VIN. Via Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings > Access point (SSID) • Enable satellite map for navigation (if equipped) Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom right-hand corner of the Navigation map screen. Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 16 e-tron Technician Reference Document Vehicle Preparation Interior • Perform any open campaigns • Check operation of window, lock, and seat controls Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing For vehicles equipped with the power door closing feature, check all doors for proper closing Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify operation of heated/ventilated and massaging seats (front/rear) (if equipped) Check both front and rear. Massaging feature is in the front seats only (if equipped) • Verify proper operation of climate control Ensure proper heating and A/C cooling, open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on” Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Setup/Settings menu: Home > Settings > General > Measurement Units > Consumption (electric motor) to mi/kWh, and check to ensure all other units are set to US specs • Verify Speech Dialog System is operating Lighting and Windshield • Test front washers (and headlight washers if equipped) Headlights must be on to test functionality of the headlight washers Trunk Inspection • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit Effective 3-20-2019-US Version 1.6 Press the “Talk” button and verify several commands • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, Settings > Music volume while parking (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance Settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual > Select Off Model Year 2019 | Audi Pre-Delivery Reference Document | 17 e-tron Technician Reference Document Media / Radio / SAT Driver Assistance • Verify HD Radio is turned “off” • Verify operation of parking system This can be found in the Radio/Settings Menu Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” ) • Check Wi-Fi® hotspot visibility. No data available at PDI due to dealer demo mode (if equipped) Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Check Wi-Fi® hotspot functionality is enabled and verify the Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX is the last four digits of the VIN. Via Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings > Access point (SSID) • Enable satellite map for navigation (if equipped) Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom right-hand corner of the Navigation map screen. On-Hoist Inspection • Inspect wheel bolts for proper torque Use torque wrench to verify • Install wheel bolt covers and center caps as supplied Wheel bolt covers can be found in the PDI kit • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify electric motor performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 18 Q3 Technician Reference Document Vehicle Preparation Trunk Inspection (continued) • Perform any open campaigns • Install wheel bolt cover removal tool from PDI kit into trunk lid tool kit Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit to the right of the spare tire • Set spare tire pressure See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification Delivery Inspection total • Start program by selecting “Carry out check” Interior • Continue to follow instructions on screen and complete the process • Check operation of window, lock, and seat controls • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk manually and remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Lighting and Windshield • Test front washers (and headlight washers if equipped) Headlights must be on to test functionality of the headlight washers Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” (if equipped with navigation) Change time zone appropriate to the dealer location Trunk Inspection • Verify power tailgate is operational and set default opening height Adjust the trunk lid opening height to 77.7 inches (197 cm) from the ground to the close button in the rear lid. Press and hold the close button in the rear lid for at least four seconds to program the opening height • Set “Entertain. Fad.” in Parking aid to an audible level (if equipped) Via “ Menu > Vehicle > Left Option > Drive Assistance > Parking Aid” • Verify and set language and measurement units This can be changed in the Setup/Settings menu • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 19 Q3 Technician Reference Document Settings (continued) Driving Performance (continued) • Set dealership location in navigation (if equipped) • Verify engine performance and acceleration Set dealership location for following back to dealership during road test Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Right Option > Wi-Fi® options > Wi-Fi® “On”) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system • Enable satellite map for navigation (if equipped) Enable Google Earth view in the Navigation > Map Settings and verify the white Google logo appears in the bottom right-hand corner of the MMI screen next to the LTE symbol. On-Hoist Inspection Driver Assistance • Verify operation of parking system plus with rear cross traffic assist (if equipped) Verify operation of Audi parking system sensors with rear view camera Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify • Set and store tire pressures for either sold vehicle OR stock inventory vehicle. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 20 Q5/SQ5 Technician Reference Document Vehicle Preparation Lighting and Windshield • Perform any open campaigns • Test front washers (and headlight washers if equipped) Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk manually and remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing (if equipped) For vehicles equipped with the power door closing feature, check all doors for proper closing • Prepare the base bars for customer delivery (install bars only upon customer request) Install the rubber strips to the top of the base carrier bars (do not install the carrier bars on the vehicle unless customer has requested). Repackage the bars into the box if they are not being installed on the vehicle. Retrieve the paper with the torque wrench key code from the base carrier bar box. Insert the paper with the key code into the owner’s literature wallet. Record torque wrench key code in the VDF to ensure it’s documented in the event the paper with the code is misplaced Effective 3-20-2019-US Version 1.6 Headlights must be on to test functionality of the headlight washers Trunk Inspection • Verify power tailgate is operational and set default opening height Adjust the trunk lid opening height to 77.7 inches (197 cm) from the ground to the close button in the rear lid. Press and hold the close button in the rear lid for at least four seconds to program the opening height • Install wheel bolt cover removal tool from PDI kit into trunk lid toolkit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit to the right of the spare tire • Set spare tire pressure See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Model Year 2019 | Audi Pre-Delivery Reference Document | 21 Q5/SQ5 Technician Reference Document Settings On-Hoist Inspection (continued) • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” • Set and store tire pressures for either sold vehicle OR stock inventory vehicle (See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet) If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Setup/Settings menu • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Via “ Menu > Vehicle > Left Option > Drive Assistance > Parking Aid” • Set “Music volume while parking” to 6 lines Accessed via MMI rear view camera display, Settings > Music volume while parking (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual->Select Off Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Right Option > Wi-Fi® options > Wi-Fi® “On”) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system • Enable Google Earth view for navigation (if equipped) Enable Google Earth view in the Navigation > Map Settings and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol. Driver Assistance • Verify operation of parking system (if equipped) Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 22 Q7 Technician Reference Document Vehicle Preparation Trunk Inspection (continued) • Perform any open campaigns • Install wheel bolt cover removal tool from PDI kit into trunk lid toolkit Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit to the right of the spare tire • Check battery clamps for proper torque Refer to Elsa Pro for specification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) and child safety features • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • Check rear view mirror operation • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Verify operation of heated/ventilated and massaging seats (if equipped) • Exit diagnosis; diagnostic log for delivery inspection is sent automatically Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk manually and remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing (if equipped) For vehicles equipped with the power door closing feature, check all doors for proper closing Lighting and Windshield • Test front washers (and headlight washers if equipped) Headlights must be on to test functionality of the headlight washers Trunk Inspection • Verify power tailgate is operational and set to maximum opening height (if equipped) Press and hold the close button in the rear lid for at least four seconds to program the opening height. Verify operation of handsfree release (if equipped) Effective 3-20-2019-US Version 1.6 Check self-dimming function/lighting (if equipped) Check both front and rear. Massaging feature is in the front seats only (if equipped) • Verify operation of manual folding 2nd row and power folding 3rd row seats Controls for the power folding 3rd row are located in the trunk • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Verify and set language and measurement units This can be changed in the Setup/Settings menu • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Via “ Menu > Vehicle > Left Option > Drive Assistance > Parking Aid” Model Year 2019 | Audi Pre-Delivery Reference Document | 23 Q7 Technician Reference Document Settings (continued) Driving Performance • Set “Music volume while parking” to medium • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi Accessed via MMI rear view camera display, Settings > Music volume while parking (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual >Select Off Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Right Option > Wi-Fi® options > Wi-Fi® “On”) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system • Enable Google Earth view for navigation (if equipped) Enable Google Earth view in the Navigation > Map Settings and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify • Set and store tire pressures for either sold vehicle OR stock inventory vehicle (See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet) If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 24 Q8 Technician Reference Document Vehicle Preparation Trunk Inspection (continued) • Perform any open campaigns • Install wheel bolt cover removal tool from PDI kit into trunk lid toolkit Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk manually and remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing (if equipped) For vehicles equipped with the power door closing feature, check all doors for proper closing Lighting and Windshield • Test front washers (and headlight washers if equipped) Headlights must be on to test functionality of the headlight washers Trunk Inspection • Verify power tailgate is operational and set to maximum opening height (if equipped) Press and hold the close button in the rear lid for at least four seconds to program the opening height. Verify operation of handsfree release (if equipped) Effective 3-20-2019-US Version 1.6 Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit to the right of the spare tire • Check battery clamps for proper torque Refer to Elsa Pro for specification • Set spare tire pressure See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) and child safety features • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify operation of heated/ventilated and massaging seats (if equipped) Check both front and rear. Massaging feature is in the front seats only (if equipped) • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Setup/Settings menu • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands Model Year 2019 | Audi Pre-Delivery Reference Document | 25 Q8 Technician Reference Document Settings (continued) Driving Performance • Set “Music volume while parking” to medium • Verify engine Start-Stop System functionality Accessed via MMI rear view camera display, Settings > Music volume while parking (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual >Select Off Media / Radio / SAT Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” ) • Check Wi-Fi® hotspot visibility. No data available at PDI due to dealer demo mode (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX is the last four digits of the VIN. Via Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings > Access point (SSID) • Enable satellite map for navigation (if equipped) Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom right-hand corner of the Navigation map screen. Driver Assistance • Verify operation of parking system Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify • Set and store tire pressures for either sold vehicle OR stock inventory vehicle (See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet) If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 26 TT Coupe & Roadster/TTS/TT RS Technician Reference Document Vehicle Preparation Interior (continued) • Perform any open campaigns • Inspect mirrors for proper operation Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) Trunk Inspection • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit • Set spare tire pressure (NA for TT RS) See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet under Pre-Delivery Inspection • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Inspect folding, adjustments, right side tilt in reverse, heating • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Settings menu by going to Menu > Vehicle > Vehicle settings • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Via “Menu > Vehicle > Left Option > Driver Assistance > Parking Aid” • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual->Select Off Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu On-Hoist Inspection • Inspect wheel bolts for proper torque Use torque wrench to verify • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 27 TT Coupe & Roadster/TTS/TT RS Technician Reference Document On-Hoist Inspection (continued) • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2019 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/vibration/pulsation Driver Assistance • Verify operation of Audi parking system plus (if equipped) Verify operation of Audi parking system sensors with rear view camera (if equipped) Roadster Functionality (if equipped) • Test operation of power folding top Perform with engine running to conserve battery power Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature Effective 3-20-2019-US Version 1.6 Model Year 2019 | Audi Pre-Delivery Reference Document | 28