NTB16-029
Service Bulletin Details
Public Details for: NTB16-029
2013-2015 pathfinder; mil on with dtc P0116
Models from 2015
2015 NISSAN PATHFINDER |
Models from 2014
2014 NISSAN PATHFINDER |
Models from 2013
2013 NISSAN PATHFINDER |
Classification: Reference: EC16-007 Date: NTB16-029 March 23, 2016 2013-2015 PATHFINDER; MIL ON WITH DTC P0116 APPLIED VEHICLES: 2013-2015 Pathfinder (R52) NOTE: This bulletin does not apply to Pathfinder Hybrid vehicles IF YOU CONFIRM The MIL is ON with P0116 Engine Coolant Temperature (ECT SENSOR) stored, and There are no drivability issues. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. 1/9 SERVICE PROCEDURE NOTE: Most instructions for reprogramming with CONSULT-III plus (C-III plus) are displayed on the CONSULT PC screen. If you are not familiar with the reprogramming procedure, click here. This will link you to the "CONSULT- III plus (C-III plus) ECM Reprogramming" general procedure. Take the vehicle for a 10 minute drive in order to meet the following Idle Air Volume Learn (IAVL) conditions: Engine coolant temperature: 70 -100°C (158 - 212°F) Battery voltage: More than 12.9V (At idle) Transmission: Warmed up Figure A After reprogramming is complete, you will be required to perform Throttle Valve Closed Position, Idle Air Volume Learn, Accelerator Closed Position, and DTC erase. The above conditions are required for the IAVL to complete CAUTION: Connect the GR8 to the 12V battery and select ECM Power Supply Mode. If the vehicle battery voltage drops below 12.0V or above 15.5V during reprogramming, the ECM may be damaged. Be sure to turn OFF all vehicle electrical loads. If a vehicle electrical load remains ON, the ECM may be damaged. Be sure to connect the AC Adapter. If the CONSULT PC battery voltage drops during reprogramming, the process will be interrupted and the ECM may be damaged. Turn off all external Bluetooth® devices (e.g., cell phones, printers, etc.) within range of the CONSULT PC and the VI. If Bluetooth® signal waves are within range of the CONSULT PC during reprogramming, reprogramming may be interrupted and the ECM may be damaged. 2/9 NTB16-029 1. Connect the CONSULT PC to the vehicle to begin the reprogramming procedure. 2 Start C-III plus. 3. Wait for the plus VI to be recognized. The serial number will display when the plus VI is recognized. 4. Select Re/programming, Configuration. VI is recognized Step 4 Figure 1 5. Follow the on-screen instructions and navigate the C-III plus to the screen shown in Figure 2 on the next page. 3/9 NTB16-029 6. When you get to the screen shown in Figure 2, confirm this bulletin applies as follows. A. Find the ECM Part Number and write it on the repair order. NOTE: This is the current ECM Part Number (P/N). 6A: Current ECM P/N Figure 2 B. Compare the P/N you wrote down to the numbers in the Current ECM Part Number column in Table A below. If there is a match, this bulletin applies. Continue with the reprogramming procedure. If there is not a match, this bulletin does not apply. Close C-III plus and refer to ASIST for further diagnostic information. Table A MODEL 2013 Pathfinder CURRENT ECM PART NUMBER: 237103KA1A, 3KA1B, 3KA1C 3KA2A, 3KA2B, 3KA2C 2014 Pathfinder 9PA0A, 9PA0B, 9PA0C 9PA1A, 9PA1B, 9PA1C 2015 Pathfinder 9PB0A, 9PB0B, 9PB0C 9PB1A, 9PB1B, 9PB1C 4/9 NTB16-029 7. Follow the on-screen instructions to navigate C-III plus and reprogram the ECM. NOTE: In some cases, more than one new P/N for reprogramming is available. If more than one new P/N is available, the screen in Figure 3 displays. Select and use the reprogramming option that does not have the message “Caution! Use ONLY with NTBXX-XXX”. If you get this screen and it is blank (no reprogramming listed), it means there is no reprogramming available for this vehicle. Close C-III plus and refer back to ASIST for further diagnosis. Figure 3 5/9 NTB16-029 8. When the screen in Figure 4 displays, reprogramming is complete. NOTE: If the screen in Figure 4 does not display (indicating that reprogramming did not complete), refer to the information on page 7. 9. Disconnect the battery charger from the vehicle. 10. Select Next. Step 10 Figure 4 NOTE: In the next steps, starting on page 8, you will perform Throttle Valve Closed Position, Idle Air Volume Learn, Accelerator Closed Position, and DTC erase. These operations are required before C-III plus will provide the final reprogramming confirmation report. 6/9 NTB16-029 ECM recovery: Do not disconnect plus VI or shut down Consult III plus if reprogramming does not complete. If reprogramming does not complete and the “!?” icon displays as shown in Figure 5: Check battery voltage (12.0–15.5 V). Ignition is ON, engine OFF. External Bluetooth® devices are OFF. All electrical loads are OFF. Select retry and follow the on screen instructions. “Retry” may not go through on first attempt and can be selected more than once. Figure 5 If reprogramming does not complete and the “X” icon displays as shown in Figure 6: Check battery voltage (12.0 – 15.5 V). CONSULT A/C adapter is plugged in. Ignition is ON, engine OFF. Transmission is in Park. All C-III plus / VI cables are securely connected. All C-III plus updates are installed. Select Home, and restart the reprogram procedure from the beginning. Figure 6 7/9 NTB16-029 11. Follow the on-screen instructions to perform the following: Throttle Valve Closed Position. Idle Air Volume Learn (IAVL). NOTE: Listed below are common conditions required for IAVL to complete. If IAVL does not complete within a few minutes, a condition may be out of range. Refer to the appropriate Electronic Service Manual (ESM) for specific conditions required for the vehicle you are working on. o Engine coolant temperature: 70 -100° C (158 - 212°F) o Battery voltage: More than 12.9V (At idle) o Selector lever: P or N o Electric load switch: OFF (Air conditioner, headlamp, rear window defogger) o Steering wheel: Neutral (Straight-ahead position) o Vehicle speed: Stopped o Transmission: Warmed up Accelerator Pedal Close Position Learning Erase DTCs Continue to the next page. 8/9 NTB16-029 12. When the entire reprogramming process is complete, the screen in Figure 7 will display. 13. Verify the before and after part numbers are different. 14. Print a copy of this screen (Figure 7) and attach it to the repair order for warranty documentation. 15. Select Confirm. Step 13 Step 14 Step 15 Figure 7 16. Close C-III plus. 17. Turn the ignition OFF. 18. Disconnect the plus VI from the vehicle. CLAIMS INFORMATION Submit a Primary Part (PP) line claim using the following claims coding: DESCRIPTION OP CODE PFP SYM DIAG FRT Reprogram Engine Control DE97AA (1) ZE 32 (2) Module - ECM (1) Refer to the electronic parts catalog (FAST) and use the ECM assembly part number as the Primary Failed Part (PFP). (2) Reference the Nissan Online Warranty Flat Rate Manual and use the indicated flat rate time. 9/9 NTB16-029