21TechRefGde526
Service Bulletin Details
Public Details for: 21TechRefGde526
All models except q3, r8, and tt: settings section: split verify and set language & measurements checklist items into 2 separate with instructions. Changed instructions for "set entertainment fad in parking aid", " set music volune while p
Models from 9999
9999 AUDI AUDI |
Models from 2021
2021 Pre-Delivery Inspection Technician Reference Document Effective 5-26-2021-US Version 1.3 Table of Contents Technician Reference Document Technician Reference Document Overview The Pre-Delivery Inspection Technician Reference Document is designed to be a resource used in hand with the Pre-Delivery Inspection Checklist (PDI). The PDI Checklist has been simplified to make the process more efficient, and in doing so, this document has been created to be used as a reference for checklist items that may have additional information. On the PDI Checklist, you find that certain items have been notated with an asterisk symbol (*), this lets you know that additional information can be found in this Technician Reference Document. Below you will find a list of each model, with the page numbers to their left. After navigating to the desired page, you will notice each model page is formatted similarly to the PDI Checklists. After each section title is the original checklist item, followed by any additional information specific to that model. Table of Contents 3-4 A4/S4/A4 allroad 5-6 A5/S5/RS 5 7-9 A6/S6/A6 allroad/RS 6 Avant 10-12 A7/A7 PHEV/S7/RS 7 13-14 A8 L/A8 PHEV/S8 15-16 e-tron 17-18 Q3 19-21 Q5/Q5 PHEV/Q5 Sportback/SQ5 22-23 Q7/SQ7 24-25 Q8/SQ8/RS Q8 26-27 R8 Coupe/Spyder 28-29 TT/TTS/TT RS Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 2 A4/S4/A4 allroad Technician Reference Document Vehicle Preparation Trunk Inspection (continued) • Perform any open campaigns • Set spare tire pressure Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) Lighting and Windshield • Test front washers (and headlight washers if equipped). Correct aim if necessary Headlights must be on to test functionality of the headlight washers See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating • Check rear view mirror operation Check self-dimming function/lighting • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” Change time zone appropriate to the dealer location • Verify and set language This can be changed in the Settings menu by going to Home > Settings > Language & Keyboard • Verify and set measurement units This can be changed in the Settings menu by going to Home > Settings > General > Measurement Units • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Trunk Inspection • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit Effective 5-26-2021-US Version 1.3 Via “Home > Vehicle > Parking Aid” • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, “Home > Vehicle > Parking Aid” (applies to vehicles with park assist or rear view camera) Model Year 2021 | Audi Pre-Delivery Reference Document | 3 A4/S4/A4 allroad Technician Reference Document Settings (continued) Driver Assistance • Set dealership location in navigation (if equipped) • Verify operation of parking system (if equipped) Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Home > Vehicle > Driver Assistance > Speed Warning > Manual Warning Threshold = “off” Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Home > Radio > Gear icon (top right corner) On-Hoist Inspection Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-up display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature • Inspect wheel bolts for proper torque Use torque wrench to verify • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Home > Vehicle > Settings & Service > Tire pressure monitoring Driving Performance • Verify engine Start-Stop System functionality Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Home > Settings > Connection Settings > Wi-Fi > Wi-Fi hotspot settings) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDI_MMI_XXXX”, where XXXX = the last four digits of the VIN are automatically preset in the system • Enable satellite map view for navigation (if equipped) Enable satellite map view in the Home > Navigation > Gear Icon (top right corner) > Map Settings > Satellite map, and verify the satellite imagery appears in the navigation map screen Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 4 A5/S5/RS 5 Technician Reference Document Vehicle Preparation Trunk Inspection (continued) • Perform any open campaigns • Set spare tire pressure Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” Change time zone appropriate to the dealer location • Verify and set language This can be changed in the Settings menu by going to Home > Settings > Language & Keyboard • Verify and set measurement units Lighting and Windshield • Test windshield washers. Correct aim if necessary Headlights must be on to test functionality of the headlight washers Trunk Inspection • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit Effective 5-26-2021-US Version 1.3 This can be changed in the Settings menu by going to Home > Settings > General > Measurement Units • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Via “Home > Vehicle > Parking Aid” • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, “Home > Vehicle > Parking Aid” (applies to vehicles with park assist or rear view camera) Model Year 2021 | Audi Pre-Delivery Reference Document | 5 A5/S5/RS 5 Technician Reference Document Settings (continued) Driver Assistance • Set dealership location in navigation (if equipped) • Verify operation of parking system (if equipped) Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Home > Vehicle > Driver Assistance > Speed Warning > Manual Warning Threshold = “off” Media / Radio / SAT Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) • Verify HD Radio is turned “off” This can be found in the Home > Radio > Gear icon (top right corner) On-Hoist Inspection Convertible Functionality (if equipped) • Test operation of power folding top Perform with engine running to conserve battery power • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Home > Vehicle > Settings & Service > Tire pressure monitoring Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Home > Settings > Connection Settings > Wi-Fi > Wi-Fi hotspot settings) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDI_MMI_XXXX”, where XXXX = the last four digits of the VIN are automatically preset in the system • Enable satellite map view for navigation (if equipped) Enable satellite map view in the Home > Navigation > Gear Icon (top right corner) > Map Settings > Satellite map, and verify the satellite imagery appears in the navigation map screen Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 6 A6/S6/A6 allroad/RS 6 Avant Technician Reference Document Vehicle Preparation Trunk Inspection • Perform any open campaigns • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit • Set spare tire pressure See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification • Place one PR Number Label in the Warranty and Maintenance Book inside front cover and one on the Rear Panel Sill Frame under the luggage compartment floor, if not already there For vehicles produced prior to September 12, 2018 Labels are located in the trunk on top of spare tire Rear Panel Sill Frame location: Top Arrow • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing (if equipped) For vehicles equipped with the power door closing feature, check all doors for proper closing Lighting and Windshield • Test front washers (and headlight washers if equipped). Correct aim if necessary Headlights must be on to test functionality of the headlight washers Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 7 A6/S6/A6 allroad/RS 6 Avant Technician Reference Document Trunk Inspection (continued) Settings Warranty and Maintenance inside cover placement • Set Time source setting to “GPS” and set Auto daylight savings time to “on” Change time zone appropriate to the dealer location • Verify and set language This can be changed in the Settings menu by going to Home > Settings > Language & Keyboard • Verify and set measurement units This can be changed in the Settings menu by going to Home > Settings > General > Measurement Units • Set “Entertain. Fad.” in Parking aid to an audible level Via “Home > Vehicle > Parking Aid” • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, “Home > Vehicle > Parking Aid” (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify operation of heated/ventilated and massaging seats (if equipped) Check both front and rear. Massaging feature is in the front seats only (if equipped) • Verify proper operation of climate control* Ensure proper heating and A/C cooling, open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Effective 5-26-2021-US Version 1.3 Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Home > Vehicle > Driver Assistance > Speed Warning > Manual Warning Threshold = “off” Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Home > Radio > Gear icon (top right corner) On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Home > Vehicle > Settings & Service > Tire pressure monitoring Model Year 2021 | Audi Pre-Delivery Reference Document | 8 A6/S6/A6 allroad/RS 6 Avant Technician Reference Document Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up Display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature Audi connect® (USA ONLY) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Home > Settings > Connection Settings > Wi-Fi > Wi-Fi hotspot settings) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDI_MMI_XXXX”, where XXXX = the last four digits of the VIN are automatically preset in the system • Enable satellite map view for navigation (if equipped) Enable satellite map view in the Home > Navigation > Gear Icon (top right corner) > Map Settings > Satellite map, and verify the satellite imagery appears in the navigation map screen Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 9 A7/A7 PHEV/S7/RS 7 Technician Reference Document Vehicle Preparation Trunk Inspection • Perform any open campaigns • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit • Set spare tire pressure See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification • Place one PR Number Label in the Warranty and Maintenance Book inside front cover and one on the Rear Panel Sill Frame under the luggage compartment floor, if not already there For vehicles produced prior to September 12, 2018 Labels are located in the trunk on top of spare tire Rear Panel Sill Frame location: Top Arrow • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing (if equipped) For vehicles equipped with the power door closing feature, check all doors for proper closing Lighting and Windshield • Test front washers (and headlight washers if equipped). Correct aim if necessary Headlights must be on to test functionality of the headlight washers Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 10 A7/A7 PHEV/S7/RS 7 Technician Reference Document Trunk Inspection (continued) Settings Warranty and Maintenance inside cover placement • Set Time source setting to “GPS” and set Auto daylight savings time to “on” Change time zone appropriate to the dealer location • Verify and set language This can be changed in the Settings menu by going to Home > Settings > Language & Keyboard • Verify and set measurement units This can be changed in the Settings menu by going to Home > Settings > General > Measurement Units • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Via “Home > Vehicle > Parking Aid” • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, “Home > Vehicle > Parking Aid” (applies to vehicles with park assist or rear view camera) Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify operation of heated/ventilated and massaging seats (if equipped) Check both front and rear. Massaging feature is in the front seats only (if equipped) • Verify proper operation of climate control* Ensure proper heating and A/C cooling, open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Effective 5-26-2021-US Version 1.3 • Set dealership location in navigation Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Home > Vehicle > Driver Assistance > Speed Warning > Manual Warning Threshold = “off” Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Home > Radio > Gear icon (top right corner) On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Home > Vehicle > Settings & Service > Tire pressure monitoring Model Year 2021 | Audi Pre-Delivery Reference Document | 11 A7/A7 PHEV/S7/RS 7 Technician Reference Document Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Home > Settings > Connection Settings > Wi-Fi > Wi-Fi hotspot settings) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDI_MMI_XXXX”, where XXXX = the last four digits of the VIN are automatically preset in the system • Enable satellite map view for navigation (if equipped) Enable satellite map view in the Home > Navigation > Gear Icon (top right corner) > Map Settings > Satellite map, and verify the satellite imagery appears in the navigation map screen Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 12 A8 L/A8 PHEV/S8 Technician Reference Document Vehicle Preparation Trunk Inspection • Perform any open campaigns • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit • Set spare tire pressure See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • Inspect mirrors for proper operation • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Check rear view mirror operation • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Verify operation of heated/ventilated and massaging seats (if equipped) • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing For vehicles equipped with the power door closing feature, check all doors for proper closing Lighting and Windshield • Test front washers (and headlight washers if equipped). Correct aim if necessary Headlights must be on to test functionality of the headlight washers Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) Check self-dimming function/lighting (if equipped) Check both front and rear. Massaging feature is in the front seats only (if equipped) • Verify proper operation of climate control Ensure proper heating and A/C cooling, open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on” Change time zone appropriate to the dealer location • Verify and set language This can be changed in the Settings menu by going to Home > Settings > Language & Keyboard • Verify and set measurement units This can be changed in the Settings menu by going to Home > Settings > General > Measurement Units Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 13 A8 L/A8 PHEV/S8 Technician Reference Document Settings (continued) Driving Performance (continued) • Verify Speech Dialog System is operating • Test drive vehicle applying brakes several times Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Via “Home > Vehicle > Parking Aid” • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, “Home > Vehicle > Parking Aid” (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Home > Vehicle > Driver Assistance > Speed Warning > Manual Warning Threshold = “off” Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Home > Radio > Gear icon (top right corner) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Home > Vehicle > Settings & Service > Tire pressure monitoring Driving Performance Audi connect® (USA ONLY) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Home > Settings > Connection Settings > Wi-Fi > Wi-Fi hotspot settings) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDI_MMI_XXXX”, where XXXX = the last four digits of the VIN are automatically preset in the system • Enable satellite map view for navigation (if equipped) Enable satellite map view in the Home > Navigation > Gear Icon (top right corner) > Map Settings > Satellite map, and verify the satellite imagery appears in the navigation map screen • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 14 e-tron Technician Reference Document Vehicle Preparation Trunk Inspection • Perform any open campaigns • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit • Select “Diagnosis” mode and start diagnosis Interior • Perform vehicle identification • Check operation of window, lock, and seat controls • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing For vehicles equipped with the power door closing feature, check all doors for proper closing Lighting and Windshield • Test front washers (and headlight washers if equipped). Correct aim if necessary Headlights must be on to test functionality of the headlight washers Effective 5-26-2021-US Version 1.3 Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify operation of heated/ventilated and massaging seats (front/rear) (if equipped) Check both front and rear. Massaging feature is in the front seats only (if equipped) • Verify proper operation of climate control Ensure proper heating and A/C cooling, open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on” Change time zone appropriate to the dealer location • Verify and set language This can be changed in the Settings menu by going to Home > Settings > Language & Keyboard • Verify and set measurement units This can be changed in the Settings menu by going to Home > Settings > General > Measurement Units • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Via “Home > Vehicle > Parking Aid” Model Year 2021 | Audi Pre-Delivery Reference Document | 15 e-tron Technician Reference Document Settings (continued) Driving Performance (continued) • Set “Music volume while parking” to medium • Calibrate rear view mirror Accessed via MMI rear view camera display, “Home > Vehicle > Parking Aid” (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Home > Vehicle > Driver Assistance > Speed Warning > Manual Warning Threshold = “off” • Disable climate control via door unlock Main screen => Vehicle => Climate control => select small temperature gauge symbol in upper right section => settings (“wheel” upper right) => unselect (disable) “Start A/C after unlocking”. Check and adjust, if needed. Button position “off”, in left position Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Home > Radio > Gear icon (top right corner) On-Hoist Inspection • Inspect wheel bolts for proper torque Use torque wrench to verify • Install wheel bolt covers and center caps as supplied Wheel bolt covers can be found in the PDI kit Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Home > Settings > Connection Settings > Wi-Fi > Wi-Fi hotspot settings) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDI_MMI_XXXX”, where XXXX = the last four digits of the VIN are automatically preset in the system • Enable satellite map view for navigation (if equipped) Enable satellite map view in the Home > Navigation > Gear Icon (top right corner) > Map Settings > Satellite map, and verify the satellite imagery appears in the navigation map screen • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Home > Vehicle > Settings & Service > Tire pressure monitoring Driving Performance • Verify electric motor performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 16 Q3 Technician Reference Document Vehicle Preparation Trunk Inspection • Perform any open campaigns • Verify power tailgate is operational and set default opening height Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk manually and remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) Lighting and Windshield • Test front washers (and headlight washers if equipped). Correct aim if necessary Headlights must be on to test functionality of the headlight washers Adjust the trunk lid opening height to 77.7 inches (197 cm) from the ground to the close button in the rear lid. Press and hold the close button in the rear lid for at least four seconds to program the opening height • Install wheel bolt cover removal tool from PDI kit into trunk lid tool kit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit to the right of the spare tire • Set spare tire pressure See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” (if equipped with navigation) Change time zone appropriate to the dealer location Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 17 Q3 Technician Reference Document Settings (continued) Driving Performance • Set “Entertain. Fad.” in Parking aid to an audible level (if equipped) • Verify engine Start-Stop System functionality Via “ Menu > Vehicle > Left Option > Drive Assistance > Parking Aid” • Verify and set language and measurement units This can be changed in the Setup/Settings menu • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Right Option > Wi-Fi® options > Wi-Fi® “On”) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system plus with rear cross traffic assist (if equipped) Verify operation of Audi parking system sensors with rear view camera Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature • Enable satellite map view for navigation (if equipped) Enable satellite map view in the Navigation > Gear Icon > Map Settings, and verify the satellite imagery appears in the navigation map screen On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 18 Q5/Q5 PHEV/Q5 Sportback/SQ5 Technician Reference Document Vehicle Preparation Exterior (continued) • Perform any open campaigns • Prepare the base bars for customer delivery (install bars only upon customer request) Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process Install the rubber strips to the top of the base carrier bars (do not install the carrier bars on the vehicle unless customer has requested). Repackage the bars into the box if they are not being installed on the vehicle. Retrieve the paper with the torque wrench key code from the base carrier bar box. Insert the paper with the key code into the owner’s literature wallet. Record torque wrench key code in the VDF to ensure it’s documented in the event the paper with the code is misplaced Lighting and Windshield • Test front washers (and headlight washers if equipped). Correct aim if necessary Headlights must be on to test functionality of the headlight washers • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan Trunk Inspection • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Verify power tailgate is operational and set default opening height • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk manually and remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing (if equipped) For vehicles equipped with the power door closing feature, check all doors for proper closing Adjust the trunk lid opening height to 77.7 inches (197 cm) from the ground to the close button in the rear lid. Press and hold the close button in the rear lid for at least four seconds to program the opening height • Install wheel bolt cover removal tool from PDI kit into trunk lid toolkit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit to the right of the spare tire • Set spare tire pressure See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 19 Q5/Q5 PHEV/Q5 Sportback/SQ5 Technician Reference Document Interior (continued) On-Hoist Inspection • Verify proper operation of climate control • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit When installing, ensure proper alignment to the valve stem (indentation in the wheel) lines up with the tab on the center cap to ensure correct mounting Ensure proper heating and A/C cooling and open all panel vents • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” Change time zone appropriate to the dealer location • Verify and set language This can be changed in the Settings menu by going to Home > Settings > Language & Keyboard • Verify and set measurement units This can be changed in the Settings menu by going to Home > Settings > General > Measurement Units • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Via “Home > Vehicle > Parking Aid” • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, “Home > Vehicle > Parking Aid” (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning This can be changed in the Driver Assistance settings by going to Home > Vehicle > Driver Assistance > Speed Warning > Manual Warning Threshold = “off” Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Home > Radio > Gear icon (top right corner) • Inspect wheel bolts for proper torque Use torque wrench to verify • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Home > Vehicle > Settings & Service > Tire pressure monitoring Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 20 Q5/Q5 PHEV/Q5 Sportback/SQ5 Technician Reference Document Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Home > Settings > Connection Settings > Wi-Fi > Wi-Fi hotspot settings) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDI_MMI_XXXX”, where XXXX = the last four digits of the VIN are automatically preset in the system • Enable satellite map view for navigation (if equipped) Enable satellite map view in the Home > Navigation > Gear Icon (top right corner) > Map Settings > Satellite map, and verify the satellite imagery appears in the navigation map screen Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 21 Q7/SQ7 Technician Reference Document Vehicle Preparation Trunk Inspection • Perform any open campaigns • Verify power tailgate is operational and set to maximum opening height (if equipped) Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk manually and remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing (if equipped) For vehicles equipped with the power door closing feature, check all doors for proper closing Lighting and Windshield • Test front washers (and headlight washers if equipped). Correct aim if necessary Headlights must be on to test functionality of the headlight washers Press and hold the close button in the rear lid for at least four seconds to program the opening height. Verify operation of handsfree release (if equipped) • Install wheel bolt cover removal tool from PDI kit into trunk lid toolkit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit to the right of the spare tire • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) and child safety features • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify operation of heated/ventilated and massaging seats (if equipped) Check both front and rear. Massaging feature is in the front seats only (if equipped) • Verify operation of manual folding 2nd row and power folding 3rd row seats Controls for the power folding 3rd row are located in the trunk • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” Change time zone appropriate to the dealer location Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 22 Q7/SQ7 Technician Reference Document Settings (continued) Driving Performance • Verify and set language • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi This can be changed in the Settings menu by going to Home > Settings > Language & Keyboard • Verify and set measurement units This can be changed in the Settings menu by going to Home > Settings > General > Measurement Units • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Via “Home > Vehicle > Parking Aid” • Set “Music volume while parking” to medium • Accessed via MMI rear view camera display, “Home > Vehicle > Parking Aid” (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Home > Vehicle > Driver Assistance > Speed Warning > Manual Warning Threshold = “off” Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Home > Radio > Gear icon (top right corner) • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Home > Vehicle > Settings & Service > Tire pressure monitoring Effective 5-26-2021-US Version 1.3 Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Home > Settings > Connection Settings > Wi-Fi > Wi-Fi hotspot settings) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDI_MMI_XXXX”, where XXXX = the last four digits of the VIN are automatically preset in the system • Enable satellite map view for navigation (if equipped) Enable satellite map view in the Home > Navigation > Gear Icon (top right corner) > Map Settings > Satellite map, and verify the satellite imagery appears in the navigation map screen Model Year 2021 | Audi Pre-Delivery Reference Document | 23 Q8/SQ8/RS Q8 Technician Reference Document Vehicle Preparation Trunk Inspection • Perform any open campaigns • Verify power tailgate is operational and set to maximum opening height (if equipped) Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk manually and remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing (if equipped) For vehicles equipped with the power door closing feature, check all doors for proper closing Lighting and Windshield • Test front washers (and headlight washers if equipped). Correct aim if necessary Headlights must be on to test functionality of the headlight washers Effective 5-26-2021-US Version 1.3 Press and hold the close button in the rear lid for at least four seconds to program the opening height. Verify operation of handsfree release (if equipped) • Install wheel bolt cover removal tool from PDI kit into trunk lid toolkit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit to the right of the spare tire • Check battery clamps for proper torque Refer to Elsa Pro for specification • Set spare tire pressure See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) and child safety features • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify operation of heated/ventilated and massaging seats (if equipped) Check both front and rear. Massaging feature is in the front seats only (if equipped) • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” Change time zone appropriate to the dealer location Model Year 2021 | Audi Pre-Delivery Reference Document | 24 Q8/SQ8/RS Q8 Technician Reference Document Settings (continued) Driving Performance • Verify and set language • Verify engine Start-Stop System functionality This can be changed in the Settings menu by going to Home > Settings > Language & Keyboard • Verify and set measurement units This can be changed in the Settings menu by going to Home > Settings > General > Measurement Units • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Via “Home > Vehicle > Parking Aid” • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, “Home > Vehicle > Parking Aid” (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Home > Vehicle > Driver Assistance > Speed Warning > Manual Warning Threshold = “off Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Home > Radio > Gear icon (top right corner) On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Home > Vehicle > Settings & Service > Tire pressure monitoring Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Home > Settings > Connection Settings > Wi-Fi > Wi-Fi hotspot settings) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDI_MMI_XXXX”, where XXXX = the last four digits of the VIN are automatically preset in the system • Enable satellite map view for navigation (if equipped) Enable satellite map view in the Home > Navigation > Gear Icon (top right corner) > Map Settings > Satellite map, and verify the satellite imagery appears in the navigation map screen Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 25 R8 Coupe & Spyder Technician Reference Document Vehicle Preparation Luggage Compartment • Set adaption channel to enable CD Ripping using Guided Functions • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Set adaptation channel (via Special functions > Service work > 5F-Activating/deactivating storage of music). Also referred to as CD Ripping. Perform 3 button reset of the MMI to complete the activation. Refer to the owner’s manual for model-specific button sequence • Perform any open campaigns Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key Lighting and Windshield • Test front washers. Correct aim if necessary Headlights must be on to test functionality of the headlight washers Effective 5-26-2021-US Version 1.3 Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating • Check rear view mirror operation Check self-dimming function/lighting • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Settings menu by going to Menu > Vehicle > Vehicle settings • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Via “Menu > Vehicle > Left Option > Driver Assistance > Parking Aid” • Set dealership location in navigation Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning This can be changed in the Driver Assistance settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual->Select Off Model Year 2021 | Audi Pre-Delivery Reference Document | 26 R8 Coupe & Spyder Technician Reference Document Media / Radio / SAT Driver Assistance • Verify HD Radio is turned “off” • Verify operation of Audi parking system plus This can be found in the Radio/Settings Menu Verify operation of Audi parking system sensors with rear view camera Audi connect® (USA ONLY) • Turn on the Wi-Fi® hotspot Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” ) • Check Wi-Fi® hotspot visibility. No data available at PDI due to dealer demo mode Check Wi-Fi® hotspot functionality is enabled and verify the Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX is the last four digits of the VIN. Via Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings > Access point (SSID) Convertible Functionality (if equipped) • Test operation of power folding top Perform with engine running to conserve battery power Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature • Enable satellite map view for navigation Enable satellite map view in the Navigation > Gear icon > Map Settings, and verify the satellite imagery appears in the navigation map screen On-Hoist Inspection • Inspect wheel bolts for proper torque Use torque wrench to verify • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 27 TT Coupe & Roadster/TTS/TT RS Technician Reference Document Vehicle Preparation Trunk Inspection • Set adaption channel to enable CD Ripping using Guided Functions (if equipped with NAV) • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Set adaptation channel (via Special functions > Service work > 5F-Activating/deactivating storage of music). Also referred to as CD Ripping. Perform 3 button reset of the MMI to complete the activation. Refer to the owner’s manual for model-specific button sequence • Perform any open campaigns Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit • Set spare tire pressure (NA for TT RS) See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet under Pre-Delivery Inspection • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating • Start program by selecting “Carry out check” • Check rear view mirror operation • Continue to follow instructions on screen and complete the process • Verify proper operation of climate control • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) Check self-dimming function/lighting (if equipped) Ensure proper heating and A/C cooling and open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Settings menu by going to Menu > Vehicle > Vehicle settings • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Via “Menu > Vehicle > Left Option > Driver Assistance > Parking Aid” • Set dealership location in navigation (if equipped) Lighting and Windshield • Test front washers. Correct aim if necessary Set dealership location for following back to dealership during road test Headlights must be on to test functionality of the headlight washers Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 28 TT Coupe & Roadster/TTS/TT RS Technician Reference Document Settings (continued) • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual->Select Off Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu On-Hoist Inspection • Inspect wheel bolts for proper torque Use torque wrench to verify • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/vibration/pulsation Driver Assistance • Verify operation of Audi parking system plus (if equipped) Verify operation of Audi parking system sensors with rear view camera (if equipped) Roadster Functionality (if equipped) • Test operation of power folding top Perform with engine running to conserve battery power Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature Effective 5-26-2021-US Version 1.3 Model Year 2021 | Audi Pre-Delivery Reference Document | 29