TSB210101-051420

Service Bulletin Details

Public Details for: TSB210101-051420

This technical service bulletin describes the verification and resolution of insite electronic service tool error message when trying to enter injector bar/trim code. This is due to incorrect 10-digit bar/trim codes being used instead of th


- 9999 -

Models from 9999
9999 CUMMINS ISL9
9999 CUMMINS ISX12
9999 CUMMINS ISX15 
6/1/2021
INSITE™ Electronic Service Tool Error Message When Trying to Enter Injector Bar/Trim Code
Technical Service Bulletin
Technical Service Bulletin: TSB210101
Released Date: 14-May-2021
INSITE™ Electronic Service Tool Error Message When Trying to Enter Injector Bar/Trim Code
INSITE™ Electronic Service Tool Error Message When Trying to Enter
Injector Bar/Trim Code
Warranty Statement
The information in this document has no effect on present warranty coverage or repair practices, nor does it authorize TRP or
Campaign actions.
Contents
Product Affected
ISC8.3 CM2250
ISL9 CM2250
ISX12/ISX11.9 CM2250
ISX15 CM2250
ISX15 CM2250SN
QSC8.3 CM2250
QSL9 CM2250
QSL9 CM2250 L115
QSX11.9 CM2250 ECF
QSX15 CM2250 ECF
QSX15 CM2250 X115
Issue
https://quickserve.cummins.com/qs3/pubsys2/xml/en/tsb/2021/tsb210101.html
1/4
6/1/2021
INSITE™ Electronic Service Tool Error Message When Trying to Enter Injector Bar/Trim Code
Symptom:
INSITE™ electronic service tool error message when trying to enter injector bar/trim code
Root Cause:
Entering a 10-digit bar/trim code can result in error messages in INSITETM electronic service tool.
Injectors have a 10-character alpha/numeric bar/trim codes printed on them. INSITETM electronic service tool requires a 9character bar/trim code to be entered for each injector.
Verification
1.
2.
3.
4.
5.
Connect INSITE™ electronic service tool to engine control module (ECM).
Select "Advanced ECM Data".
Select "High Pressure Common Rail Injector Setup".
Read information listed in "High Pressure Common Rail Injector Setup" and "Instructions" headings.
Verify injector bar/trim codes for each injector.
Resolution
While entering the bar/trim codes, enter only the last 9 characters printed on the injector. Ignore all preceding characters. See
Figure 1 below.
For detailed steps on using the INSITE™ electronic service tool to enter the injector bar/trim codes, see corresponding Service
Manual. Reference Procedure 006-026 in Section 6.
https://quickserve.cummins.com/qs3/pubsys2/xml/en/tsb/2021/tsb210101.html
2/4
6/1/2021
INSITE™ Electronic Service Tool Error Message When Trying to Enter Injector Bar/Trim Code
Figure 1, Injector Showing Last 9 Digits of Bar/Trim Codes.
Document History
Date
Details
2021-5-10
Module Created
2021-5-14
Updated Figure 1.
Last Modified: 14-May-2021
https://quickserve.cummins.com/qs3/pubsys2/xml/en/tsb/2021/tsb210101.html
3/4
6/1/2021
INSITE™ Electronic Service Tool Error Message When Trying to Enter Injector Bar/Trim Code
https://quickserve.cummins.com/qs3/pubsys2/xml/en/tsb/2021/tsb210101.html
4/4

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.