21-BE-010H
Service Bulletin Details
Public Details for: 21-BE-010H
- 9999 -
Models from 9999
9999 HYUNDAI HYUNDAI |
GROUP NUMBER BODY ELECTRICAL Technical Service Bulletin SUBJECT: DATE 21-BE-010H MODEL(S) AUGUST, 2021 VARIOUS BLIND-SPOT COLLISION WARNING (BCW/BSD) MODULE TROUBLESHOOTING INFORMATION This TSB supersedes 19-BE-009H to include another DTC code, C164C/D. Description: This bulletin provides information for troubleshooting of the Blind-Spot Collision Warning (BCW/BSD) system whenever it exhibits Diagnostic Trouble Code (DTC) C120B/D, C160A, or C164C/D. C120D15 - Left Led Circuit Short To B C120B15 - Right Led Circuit Short To B Or Open C160A88 - BSD Local CAN bus off C164C87- Local CAN time-out Rear Right C164D87- Local CAN time-out Rear Left NOTICE When a vehicle exhibits Diagnostic Trouble Code (DTC) C120B/D, C160A, or C164C/D, check the wiring harness connections before attempting to replace the Blind-Spot Collision Warning (BCW/BSD) module(s). NOTICE The information provided in this bulletin is a general guidance to assist the technician. The information is not specific to any vehicle. Please refer to the Electrical Troubleshooting Manual (ETM) for the specific model to locate the general area described below. Applicable Vehicles: All Models and Model Year equipped with the Blind-Spot Warning system. Warranty Information: Normal Warranty Applies Circulate To: General Manager, Service Manager, Parts Manager, Warranty Manager, Service Advisors, Technicians, Body Shop Manager, Fleet Repair SUBJECT: BLIND-SPOT COLLISION WARNING (BCW/BSD) MODULE TROUBLESHOOTING INFORMATION Service Procedure: DTC C120D15/C120B15 C120D15 - Left LED Circuit Short To B. This DTC refers to an electrical connection concern between the left side mirror BCW/BSD LED light indicator, and the left side BCW/BSD module. Left BSD LED Light Indicator C120B15 - Right LED Circuit Short To B or Open. This DTC refers to an electrical connection concern between the right side mirror BCW/BSD LED light indicator, and the right side BCW/BSD module. Right BSD LED Light Indicator Check the Following in Relation to the DTC: 1. Check continuity (<1ohm) from BCW/BSD module to BCW/BSD light indicator. 2. Check mirror assembly and/or wire harness for open, shorted, frayed wires or poor connector fastening. DTC C120B15/C120D15 : Check the continuity or connection condition between BCW and outside mirrors 3. Check connector pins for tension, corrosion, or damage. Confirm the connector is fully seated (disconnect and reconnect the connector). 4. If steps 1-3 are confirmed normal, then proceed with replacing the BCW/BSD module(s) according to the DTC code. NOTICE If the harnesses between the BCW/BSD modules are found faulty, down level parts (BCW Sensor, DTC C160A88 Bracket, and Wire Extension) are available. Refer to the parts catalog for the latest part number. TSB #: 21-BE-010H Page 2 of 4 SUBJECT: SUBJECT: BLIND-SPOT COLLISION WARNING (BCW/BSD) MODULE TROUBLESHOOTING INFORMATION C160A88 - BSD Local CAN bus off This DTC generally refers to an electrical connection concern between the left side and the right side BCW/BSD modules. Check the Following: 1. Check continuity (<1ohm) of the High and Low CAN line between the two BCW/BSD modules. DTC C160A88: Check the continuity or connection condition of the high and low CAN line between the two BCWs. 2. Check wire harness for open, shorted, frayed wires or poor connector fastening. 3. Check connector pins for tension, corrosion, or damage. Confirm the connector is fully seated (disconnect and reconnect the connector). 4. If steps 1-3 are confirmed normal, then proceed with replacing the BCW/BSD module(s). NOTICE If the harnesses between the BCW/BSD modules are found faulty, down level parts (BCW Sensor, Bracket, and Wire Extension) are available. Refer to the parts catalog for the latest part number. DTC C164C87/C164C87 TSB #: 21-BE-010H Page 3 of 4 SUBJECT: SUBJECT: BLIND-SPOT COLLISION WARNING (BCW/BSD) MODULE TROUBLESHOOTING INFORMATION C164C/D87 - BSD Local CAN bus off This DTC generally refers to an electrical connection concern between the left side and the right side BCW/BSD modules. Check the Following: 1. Check continuity (<1ohm) of the High and Low CAN line between the two BCW/BSD modules. 2. Check wire harness for open, shorted, frayed wires or poor connector fastening. DTC C164D87, C164C87 : Check the continuity or connection condition of the high and low CAN line between the two BCWs. 3. Check connector pins for tension, corrosion, or damage. Confirm the connector is fully seated (disconnect and reconnect the connector). 4. If steps 1-3 are confirmed normal, then proceed with replacing the BCW/BSD module(s). NOTICE If the harnesses between the BCW/BSD modules are found faulty, down level parts (BCW Sensor, Bracket, and Wire Extension) are available. Refer to the parts catalog for the latest part number. TSB #: 21-BE-010H Page 4 of 4 SUBJECT: