2064350/1

Field campaign
Topic
Market area
Brand
Transaction No.
Campaign number
Note
Type
US code
Transmission control module update during PDI (SC 21/34)
United States E05 Bentley USA and rest America (6E05)
Bentley
2064350/1
EC16
Vehicle data
New Flying Spur - W12
Sales types
Type MY Brand Designation Engine code Gearbox code Final drive code
ZG2* 2022 E
*
*
*
Chassis numbers
Manufacturer
SCB
SCB
SCB
SCB
SCB
SCB
SCB
Filler
BB6
BB6
BB6
BB6
BB6
BB6
BB6
Type
ZG
ZG
ZG
ZG
ZG
ZG
ZG
Documents
Document name
master.xml
Filler
9
9
8
8
2
4
1
MY
N
N
N
N
N
N
N
Factory
C
C
C
C
C
C
C
From
091574
091624
091517
091548
091609
091529
091603
To
Prod from Prod to
091574
091624
091517
091548
091609
091529
091603
EC16
Transmission control module update during PDI (SC 21/34)
Notes
Transaction No.: 2064350/1
Repair instructions
Technical background
Software updates are available and should be applied to the following control unit:
•
Transmission (address 02)
Remedy
Carry out the instructions within the Work section to completion
Customer notification
All vehicles must be updated during PDI
Warranty accounting instructions
Warranty Type
Damage Service Number
Damage Code
Criterion ID
Labour Operation Code
Time
790
EC16
0066
01
01 51 00 00
Must not exceed 50 TU (as per ODIS log)
Genuine parts
Not applicable
Parts supply
Not applicable.
Parts despatch control
Not applicable.
Repair instructions
Notes
Technical background
Software updates are available and should be applied to the following control unit:
•
Transmission (address 02)
Check
If the vehicle is not already listed as repaired in the “Repair History” (Elsa Pro) check for the presence of the green paint completion mark as
shown within the Identification section
Genuine parts
Not applicable
Work
Software update - Transmission control unit (Address 02)
•
The closed-circuit voltage of the vehicle must be at least 12.5 V during the update. Connect a suitable battery charger
to the vehicle. For further information refer to the Repair manual.
•
During the update switch off all unnecessary consumers (ventilation, seat heater, interior illumination etc)
•
Because of the highest transmission stability you MUST use the diagnosis interface VAS 6154 (WiFi diagnostic tool)
ONLY in USB operation or the cable-connected VAS 5055 for the reprogramming (updating) of control units. If these
units are not available, the diagnosis interface VAS 5054 (A) can also be used in USB mode
•
Do Not under any circumstances use a Bluetooth connection to conduct the reprogramming (updating) of control units
1) Select and run Guided fault finding
•
Within the Special functions tab select SVM – Problem related Hardware/Software update then select Perform test (Figure 1)
Figure 1
2) On the next screen enter SVM code 37102GB01 (Figure 2)
Figure 2
3) On the following screen, confirm the SVM code is correct
•
All control modules will now be interrogated
•
The software update will then be suggested
•
The software of 02 – Transmission Control Module (Figure 3) will be updated
NOTE: A progress bar will be displayed
Figure 3
4) Carry out all on screen prompts until completion
After the programming is complete, gear selection will not be possible. To wake up the system a bus silence is required, carry out
the following steps in the order stated below:
•
Switch off the ignition
•
Remove the diagnostic interface from the OBD port
•
Switch off and remove the battery charger from the vehicle
•
Close the bonnet and all doors, then lock the vehicle
•
Wait 5 minutes to allow the vehicle to go into bus silence
•
When 5 minutes has elapsed, unlock the vehicle and open the driver’s door
•
Switch on the ignition
•
Confirm that the gear selection is now possible
5) Clear the vehicle of any DTC’s generated as a result of performing steps 1 through to 4
6) Apply a green paint completion mark as shown in the Identification section
Identification
Green paint completion mark on the 12 volt battery retaining bracket
Repair instructions Notes